Merit Industries, Inc.
2525 State Rd.
Bensalem, PA 19020-8529
(215) 639-4700 (800) 445-9353
http:\\meritind.com
9000/1001
Megatouch XL™ Technical Service Manual Contents
Section 1 - Cabinet Information
General Information- All Cabinet Styles (Pink)
Dimensions/Shipping weights
General Information - Countertop (Blue)
Parts illustrations
Parts list
General Information - 19” Upright (Gold)
Parts illustrations
Parts list
General Information - 19” Cabaret (White)
Parts illustrations
Parts list
Section 2 - Troubleshooting Information
Touchscreens (Pink)
Troubleshooting
Advanced touchscreen calibration
Removal and Installation of Touchscreen
Glass
Microtouch touchscreen information
Access/Removal of Major Assemblies (Blue)
CD-ROM player
Monitor
Circuit Boards
Troubleshooting Guide (Gold)
Troubleshooter™ Instructions (White)
CMOS Setup (Green)
Mars 2000 Bill Acceptor (Yellow)
DIP switch settings
Coin-in menu instructions
Section 3 - Power Supply
GlobTek ST-230WF (Pink)
Parts list
Schematics
Sparkle Power International (Blue)
Schematics
Section 4 - Circuit Boards
DeAmertek CPU (Pink)
NO INFO AVAILABLE
Telco CPU (Blue)
Schematics
CRT-500 I/O Board (Gold)
Parts list
Schematics
Communications Board (White)
Parts list
Schematic
Section 5 - Monitors
Ducksan (Pink)
Schematics
Telco (Blue)
Parts list
Schematic
Tatung (Gold)
Schematics
Monitor Adjustmerts (White)
Degaussing
Color adjustment
Section 6 - Technical Service Bulletins
Field Bulletin 9
(XL CD-ROM ribbon cable/Updated
software)
Field Bulletin 10
(XL NVRAM not clearing with new
software)
Tech Notes 7
(Over-torquing I/O board screws)
General Information- All Cabinet Styles
Dimensions/shipping weights
General Information - Countertop
Parts Illustrations
Parts List
General Information - 19” Upright
Parts Illustrations
Parts List
General Information - 19” Cabaret
Parts Illustrations
Parts List
Cabinet Information Section
General Information
The Megatouch XL video games are available in several different cabinet styles:
Countertop*
Dimensions: H - 15-1/4”; W - 20”; D - 18-1/4”
Shipping weight: approx 95 lbs.
Bill acceptor option*
19” Upright
Dimensions: H - 54-1/4”; W - 24”;D - 26-1/2”
Shipping weight: approx 250 lbs.
Bill acceptor option
19” Cabaret
Dimensions: H - 61”;W - 22-1/2”;D - 24”
Shipping weight: approx. 250 lbs.
Bill acceptor option
*An optional coin mech/bill acceptor (Mars 2000) combination unit is available for all countertop
models.
Countertop
Dimensions: H - 15-1/4”; W - 20”; D - 18-1/4”
CPU Board Information
DeAmertek
Telco
Touchscreen Type
Microtouch
ELO
13” COUNTERTOP
MEGATOUCH XL PARTS LISTS
Megatouch XL CTOP
Part List
CALLOUT #
PART #
DESCRIPTION
SA0100-01
ASSY, MEGATOUCH XL, CTOP
1
MW0009-01
CHASSIS, CTOP, XL
2
MW0015-01
BRACKET, LOCK, CTOP XL
3
HW8741
LOCK, CIRC, BNT, DIFF, 1/2”
4
SA4084-02
SPEAKER ASSY, 4”, W/6-PIN CONN
5
HW8993-02
LAZY SUSAN, 12” DIA, 15 DEG. STOPS
6
HW8018-01
ANTI-SKID PAD, 11.5”DIA, RA65 RBR
7
MW0038-01
CORD CLAMP, XL
8
HW9001
TUBING, PLASTIC
9
SA0108-01
HARNESS, MAIN, CTOP, XL
10
SA0111-01
HARNESS, DISPLAY, AC, CTOP, XL
11
SA5129-01
GASKET/BEZEL ASSY
11a
HW8087
TAPE, NEOP, .18W X .38THK, PSA
11b
HW8953
BEZEL, 13’ T/S
SA0102-01
HARNESS, COIN BOX, MGATCH XL, CTOP
12
CN7508
METRIMATE PLUG, 12 PIN
13
CN7501
METRIMATE PIN, FEMALE 20-24 AWG
14
EC9154
COUNTER, 12V FROG EYE MTG
15
SW3005
PB SWITCH, MOMENTARY (SETUP/CALIBRATE)
16
MW0012-01
BRACKET, CONN/COUNTER, CTOP XL
SA0104-01
DISPLAY/MOTHERBOARD ASSY, XL
17
MW0010-01
FRAME, DISPLAY, CTOP, XL
18
EC9840
TOUCHSCREEN CONTROLLER, SMT3
19
HW8171-01
PCB GUIDE, 8”, SNAP-ON, DEEP CHANNEL
20
EC0003-01
CD-ROM PLAYER, IDE, 4X
21
SA0103-01
TOUCHSCREEN/VGA DSPLY ASSY, 13”
21a
EC9377
MONITOR, VGA, 13” (W/ CHASSIS BOARD & FRAME)
21b
EC9824
TOUCHSCREEN OVERLAY, 13’
21c
HW8078
TAPE, POLYESTER, 1”, W/ADH
21d
HW8067
TAPE, FOAM, .5W X .03 THK, DBL
22
SA0112-01
ASSY, MOTHER BOARD & I/O, XL
22a
SA10025-01
PCA, CRT-402, DE-AMER, RISER BOARD
22b
SA10023-01
PCA, I/O BOARD, XL VID, CTOP
22c
SA0101-01
ASSY, MOTHERBOARD
23
SA0118-01
CABLE, POWER EXTENSION, CD-ROM
SA0105-01
COVER ASSY, CTOP, XL
24
WD0001-01
SIDE PANEL, RIGHT, CTOP XL
25
WD0001-02
SIDE PANEL, LEFT, CTOP XL
26
MW0013-01
TOP, CTOP, XL
27
MW0016-01
DOOR, CTOP, XL
28
MW0014-01
PLATE, LATCH, CTOP, XL
29
HW8734-01
LOCK, W/O CAM, 564, 5/8”L (REAR DOOR)
30
MW0024-01
CAM, LOCK (REAR DOOR)
31
MW0023-01
BOLT, LOCK, CTOP, XL
32
HW8911-01
PIN, SPRING, STL, .094OD X .50L
33
MW5164-01
HINGE, REAR DOOR CTTS
34
EC9410
FAN, TUBAXIAL, 3”, 110V
35
SA0117-01
CABLE, POWER EXTENSION, FAN
SA0106-01
PWR ENTRY ASSY, CTOP, XL, 120V
36
EC7528
POWER SUPPLY, SW, PS/2-PC
37
MW0011-01
BARCKET, PWR SUPPLY, CTOP, XL
38
SW4024
ROCKER SW, DPST, 250V, PANEL MTG
39
TA10028-01
PCA, RS-485 COMMUNICATIONS BD, XL SYS
SA0119-01
DOOR ASSY, CD-ROM ACCESS, XL, CTOP
40
MW0039-01
DOOR, CD-ROM ACCESS, XL, CTOP
41
HW8727
LOCK, FLAT, STR, DIFF, 1-1/8 CAPKY (CD DOOR/COIN BOX)
42
MW0037-01
CAM, LOCK, .75 X 2.0
DECALS AND SIGNS
GL3100-01
DECAL, SIDE PANEL, XL, CTOP
GL3101-01
DECAL, FRONT, XL, CTOP
SA7297-06
SIGN HOLDER, MEGATOUCH XL (HOLDER & SIGN ASSEMBLY)
HW9461-03
SIGN HOLDER, PETG, 4 X 12, CTOP
PM8928-09
SIGN, MEGATOUCH XL, CTOP
COIN MECHS/BILL ACCEPTORS
25¢ USA
HW8249
FR/PLATE, SINGLE, M, .25, ROLL DOWN
$1 CANADIAN
HW8295
FR/PLATE, SINGLE, M, $1 CANADIAN
COIN BOX ASSY
SA5161-01
HARNESS, COIN BOX, MECHANICAL, CTOP, XL
MW0017-01
COIN BOX, CTOP, XL
MW5153-01
DOOR, COIN BOX, CTOP
COIN BOX/JCM B/A ASSY, $1-20, XL
EC9797
JCM B/A DBV-45 $1-20, W/ STACKER
SA0109-01
HARNESS, JCM B/A, CTOP, XL
19” Upright
Dimensions: H - 54-1/4”; W - 24”;D - 26-1/2”
CPU Board Information
DeAmertek
Telco
Touchscreen Type
Microtouch
ELO
19” UPRIGHT (FRONT ACCESS)
19” UPRIGHT (FRONT ACCESS)
19” UPRIGHT (REAR ACCESS)
19” UPRIGHT (REAR ACCESS)
19” Upright Parts List
CALLOUT #
PART #
DESCRIPTION
1
EC2001
POWER CORD, 120V
2
HW8711
ANCHOR PLATE FOR CAM LOCK
3
HW8716
LOCK, FLAT, STR, #564, 1-7/16” (REAR DOOR)
4
HW8960
LEG LEVELER, 2”, 3/8-16THD
5
MW5001-01
STAY LID, URTS, 19”
6
MW5003-01
BRACKET, CRT ADJUST, LEFT
7
MW5003-02
BRACKET, CRT ADJUST, RIGHT
8
MW5006-01
COVER, PERFORATED, SPEAKER, 4”
9
SB0010-01
COM, POWER CABLE
10
SA4084
SPEAKER ASSY, 4”
11
WD2017-01
CABINET, 19” URTS, XL/260, FA, BLK
12
SA0063-01
HARNESS, POWER, DUAL FANS, URTS
13
SA5117-05
FAN ASSY, 3”, 12V DC, 2 PIN, W/GUARD
14
HW8756
CAM, BENT, 1/8” OFFSET
15
SA0058-01
HARNESS, POWER SWITCH, URTB/URTS/CAB, XL
16
SW4024
ROCKER SWITCH, DPST, 250V, PNL MTG
17
TA10028-01
PCA, RS-485 COMM, XL SYS
18
EC2187-01
RIBBON CABLE, 9 COND, 31”L
19
HW6366
MOUNTING POST, KNURLED
20
EC9840
TOUCHSCREEN CONTROLLER BOARD, SMT-3
21
MW0057-01
COVER, FAN PROTECTOR
22
SA3209-01
BRACKET ASSY, METER/TEST SWITCH
23
MW0044-01
DOOR LOCK LATE, UR
24
SA3234-01 (-02)
SHELF, PC POWER, URTS, XL (-02 “CE” APPROVED ASSY)
24a
WD2018-01
SHELF, 19” VIDEO, UNIVERSAL
24b
MW0063-01
PLATE, MTG, PC/PWR, XL
24c
EC0007-01
TERMINAL BLOCK, 4 POSITION
24d
EC7528
POWER SUPPLY, SWT, PS-2/PC
24e
SA0077-01
HARNESS, MAIN, XL
24f
EC0003-01
CD-ROM PLAYER, IDE, 4X
24g
EC2191-06
RIBBON CABLE, 2X20 PIN, IDE, 7”L
24h
SA0067-01
HARNESS, VOLUME POT, URTS/CAB, 260
25
SA0112-01
ASSY, MOTHERBOARD & I/O, XL
25a
SA10025-01
PCA, CRT-402, DE-AMER, RISER BOARD
25b
SA10023-01
PCA, I/O BOARD, XL VID, CTOP
25c
SA0101-01
ASSY, MOTHERBOARD
26
SA3202-05
SHELF ASSY, TS/CRT (VGA)
26a
SA3210-03
TS/CRT (VGA) ASSY, COLOR, 19”
26b
EC9378
MONITOR, VGA, 19”
26c
EC9823
T/S OVERLAY, 19”
26d
HW8078
TAPE, POLYESTER, 1”, W/ADHESIVE
26e
HW8067
TAPE, FOAM, .5W, .03THK,DBL
26f
WD2013-01
SHELF, CRT MTG, 19” URTS
26g
MW5008-01
BRACKET, CRT LEFT, 19” URTS
26h
MW5008-02
BRACKET, CRT RIGHT, 19” URTS
27
SA3230-01
BEZEL ASSY, 19” URTS
27a
MW5014-01
BEZEL/HINGE ASSY, 19” URTS
27b
HW8951-02
BEZEL, MONITOR, 19” URTS
28
HW8713
LOCK, FLAT, STR, 564, 1-7/16 KYRM
19” Cabaret
Dimensions: H - 61”; W - 22-1/2”; D - 24”
CPU Board Information
DeAmertek
Telco
Touchscreen Type
Microtouch
ELO
19” CABARET
19” CABARET
19” Cabaret Parts List
CALLOUT #
PART #
DESCRIPTiON
1
EC2001
POWER CORD, 120V
2
MW1672-01
CONTROL PANEL, 19” CABARET
3
MW1671-01
BRKT, GLASS, UPPER, 19” CABARET
4
MW1670-01
SPEAKER, MTG BRKT, 19” CAB
5
HW8951-01
BEZEL, MONITOR, 19” CABARET
6
WD5060-01
WOOD CABINET, URTS, 19” CABARET
7
SA4084
SPEAKER ASSY, 4”
8
SA3209-01
BRACKET ASSY, METER/TEST SWITCH
9
HW8960
LEG LEVELER, 2”, 3/8-16THD
10
GL2411-03
PLEXI, CLEAR, 19” CABARET, SIGN
11
MW1674-01-0A
MONITOR, SUPPORT LEFT, 19” CABARET
12
MW1674-02-0A
MONITOR, SUPPORT RIGHT, 19” CABARET
13
HW8979
SLIDE LATCH
14
SA0058-01
HARN, PWR SWITCH, URTB/URTS/CAB, XL
14a
SW4024
ROCKER SWITCH, DPST, 250V, PNL MTG
15
SB6058-01
FLUOR LAMP ASSY, 120V/60HZ, 15W
15a*
LB2100
LAMP, FLUOR, 15W, F15T8CW
16
MW0028-01
PLATE, POWER ENTRY
17
HW6366
MOUNTING POST, KNURLED
18
TA10028-01
PCA, RS-485 COMM, XL SYS
19
EC2187-01
RIBBON CABLE, 9 COND, 31”L
20
EC9840
TOUCHSCREEN CONTROLLER BOARD, SMT-3
21
SA0014-01
HARN, E/M/CREJ, 19” CABARET
22
SA3266-03-0B
CRT ASSY, 19” CABARET, XL
22a*
EC9378
MONITOR, VGA, 19”
22b*
EC9823
T/S OVERLAY, 19”
22c*
HW8078
TAPE, POLYESTER, 1”, W/ADHESIVE
22d*
HW8067
TAPE, FOAM, .5W, .03THK,DBL
22e
WD5061-01-0A
SHELF, MONITOR, 19” CABARET
23*
SA3234-01 (-02)
SHELF, PC POWER, URTS, XL (-02 “CE” APPROVED ASSY)
23a
WD2018-01
SHELF, 19” VIDEO, UNIVERSAL
23b
MW0063-01
PLATE, MTG, PC/PWR, XL
23c
EC0007-01
TERMINAL BLOCK, 4 POSITION
23d
EC7528
POWER SUPPLY, SWT, PS-2/PC
23e
SA0077-01
HARNESS, MAIN, XL
23f
EC0003-01
CD-ROM PLAYER, IDE, 4X
23g
EC2191-06
RIBBON CABLE, 2X20 PIN, IDE, 7”L
23h
SA0067-01
HARNESS, VOLUME POT, URTS/CAB, 260
24*
SA0112-01
ASSY, MOTHERBOARD & I/O, XL
24a
SA10025-01
PCA, CRT-402, DE-AMER, RISER BOARD
24b
SA10023-01
PCA, I/O BOARD, XL VID, CTOP
24c
SA0101-01
ASSY, MOTHERBOARD
*This part is not called out in the drawing. It is either part of an assembly that is shown, or it is an
assembly in which all of the parts are shown separately.
Touchscreens
Troubleshooting your Touchscreen
Advanced Touchscreen Calibration
Removal/Installation of Touchscreen Glass
Microtouch Touchscreen Information
Access/Removal of Major Assemblies
CD-ROM Player
Monitor
Circuit Boards
Troubleshooting Guide
Troubleshoooter™ Software Instructions
CMOS Setup
Mars 2000 Bill Acceptor
DIP Switch Settings
Coin-In Menu Instructions
Troubleshooting Your Touchscreen
Problem 1
The touchscreen appears to lose calibration if you touch the screen while
touching the metal on the cabinet (this particular problem is most likely to affect
upright and cabaret games, not countertops).
Solution Make sure the controller and/or the cabinet is properly grounded. NOTE: For the
19" upright, you may have to remove the paint from the hinge that the ground
braid is attached to in order to get a better connection.
Problem 2
The touchscreen won't calibrate correctly. This is a vague problem that requires
more information to determine the cause. To investigate further, go to the TEST
SCREEN mode and slowly pull your finger down the screen in a vertical line.
A)
If the crosshair moves in a wavy line (sine wave) then there is a bad EEPROM in
the Microtouch touchscreen cable connector.
Solution Replace the touchscreen glass. NOTE: TO PRESERVE THE VALIDITY OF
YOUR WARRANTY, CONTACT MERIT TECHNICAL SERVICE (at 1-800-445-
9353) BEFORE ATTEMPTING ANY SERVICING.
B)
If the cursor generally follows your finger, except for one particular area on the
screen, the EEPROM is not correcting for flaws in the touchscreen glass.
Solution Repair or replace the touchscreen glass (or you can try switching touchscreen
controllers, if you have another one. This can cause the EEROM to reinitialize
itself, leaving you with both controllers working).
C)
If the crosshair moves continually towards one of the corners (the same corner
each time), every time you run your finger down the screen, the touchscreen
glass has a broken wire.
Solution Return the glass to Merit Technical Service to have it fixed.
D)
If the controller works for a while, but stops working (the TTL LED does not
respond to a touch), the controller may not be properly grounded.
Solution Install the TTL Ground/Static kit (#SA1089-01) and the CRT-266 Electro-Static
Discharge Board kit (SA1088-01). On the upright model, you may want to check
the gray and green wires from the touchscreen controller cable. They should be
attached to the ground on the power supply.
Problem 3
If the glass is totally unresponsive, check the LED on the touchscreen controller
(board).
1.
If the LED isn't flashing, touch the screen while keeping an eye on the LED. If the
LED reacts to your touch (i.e. gets brighter), the problem is with the CRT-260
board.
a) The U41, UART chip has been minorly affected by a static hit.
Solution Turn the game off, then power up. If that fixes the problem, call Merit Customer
Service for software that can prevent this problem from happening again.
b) The UART chip or the U39 Maxim chip (on the upright model) has been burnt
out by a static hit.
Solution Call Merit Technical Service at 1-800-445-9353. NOTE: Make sure to install, if
you haven’t already, the SA1089-01 Ground/Static kit to help prevent this from
happening again.
If the LED is flashing, refer to the following chart for interpretation of the error and contact
Merit Customer Service.
Flashes per 10 Second
Inerval
Error Detected
1
RAM Error
2
ROM Error
3
A/D Error
4
EEROM Error
5
Analog Error
Advanced Touchscreen Calibration
The following directions will help you calibrate your touchscreen more accurately.
1.
Enter calibrate mode. When the first dot appears, intentionally touch the screen about 1”
away from the dot, diagonally, towards the center of the screen (repeat this procedure
for the second calibration dot; see Figures 1a and 1b). You are now in TEST SCREEN
mode. As you test the screen, you should notice that the crosshair is considerably out of
calibration. By completing this step, you have shown that the machine is accepting
calibration input.
Figure 1a
Figure 1b
2.
Go back to calibrate mode, but this time touch exactly on the center of the calibration
dots, to more accurately calibrate the screen (see Figures 2a and 2b). You are now
back in TEST SCREEN mode. Touch the approximate location where the first dot
appeared. If the crosshair is not centered on your finger, note the direction and
approximate distance which it is off center. Repeat this procedure at the approximate
location of the second calibration dot (see Figures 2c and 2d). (If the crosshair is
centered on your finger, the screen is calibrated accurately.)
Figure 2a
Figure 2b
Figure 2d
Figure 2c
3.
To compensate if the screen is not calibrated accurately, return to the calibration
screen. Recalibrate the way you normally would, but don’t touch exactly on the center of
the dots. This time, touch slightly away from the dot, in the SAME direction and
approximate distance which the dot was off center (see Figures 3a and 3b). For
example, if the crosshair comes up slightly below where you touched, when you
recalibrate, touch slightly below the calibration dot, if the crosshair appears slightly
above and to the right of where you touched, when you recalibrate, touch slightly above
and to the right of the dot. This should compensate for the individuality of the
touchscreen glass and the way it was mounted on the CRT.
It may take several attempts to get the screen calibrated exactly.
Figure 3a
Figure 3b
Removal and Installation of Microtouch Touchscreen Glass Overlay
Removing the Touchscreen Overlay
1. Remove the monitor assembly as explained in the Cabinet Information Section - Removal of
Major Parts.
2. Remove the first layer of black tape around the edge of the glass.
3. Spray alcohol over the second layer of tape to loosen the adhesive.
4. Carefully cut the second layer of tape by running a razor blade along the gap between the
monitor and the touchscreen overlay.
5. While continuing to spray the tape with alcohol, remove the remaining tape by CAREFULLY
running the blade under the tape and gently peeling it up from the glass. Do this until all tape and
adhesive have been removed from the glass.
Installing the Touchscreen Overlay*
Countertop model:
1. Place the touchscreen glass over the monitor glass, so that the touchscreen cable is to your right
(when facing the monitor).
2. Apply one piece of the black, double-sided tape to each edge of the glass, to hold it to the
monitor.
3. Apply the black cloth tape around the entire perimeter of the monitor, securing the touchscreen
glass to the monitor and covering the double-sided tape.
4. Place the monitor assembly back into the cabinet and secure it in position.
5. Run the cable through a hole on the side of the monitor chassis and into the CPU section.
6. Attach the touchscreen connector to the back of the SMT-3 controller.
Upright and Cabaret models:
1. Place the touchscreen glass over the monitor glass, so that the touchscreen cable is to your right
(when facing the monitor). Upright models only*: Install the supplied foam tape around the edges
of the monitor, where it meets the bezel.
2. Place the monitor assembly back into the cabinet and secure it in position.
3. Run the cable through the rear of the cabinet and into CPU section.
4. Attach the touchscreen connector to the back of the SMT-3 controller.
* When installing a new touchscreen overlay on a 19” upright model, make certain that the metal of the
monitor bezel door does not contact the glass. The bezel should fit snugly against the foam tape,
WITHOUT CRUSHING THE TAPE. You must also recalibrate the touchscreen after closing the monitor
door.
Removal/Access of Monitor and CD Player - Countertop
1. Turn off the game and unplug it from its power source.
2. Remove the lid (for lid removal instructions see the decal located inside the rear door).
3. Remove the touchscreen controller and disconnect the touchscreen controller cable from the
back of the controller. Also, disconnect the Molex connector connecting the orange and gray
wires from the touchscreen controller cable to the main harness, and the green wire with ring
lug, that is attached to the metalwork, next to the controller. See Figure 1 for touchscreen
controller location.
4. Disconnect the monitor signal cable from the motherboard. See Figure 1.
5. Remove the four nuts securing the monitor chassis to the main chassis; two nuts are located
on each side of the monitor board. NOTE: BE CAREFUL TO AVOID THE FLYBACK
TRANSFORMER AND HIGH VOLTAGE WIRE RUNNING TO THE MONITOR. See Figure 2
for locations.
6. Disconnect the monitor power connection (black and white wires running from monitor board to
right angle connector plugged into power supply).
7. Pick up the monitor assembly and remove it from the cabinet.
8. The CD player is located underneath the monitor assembly.
FIGURE 1 - COUNTERTOP - CD PLAYER REMOVAL
FIGURE 2 - COUNTERTOP - MONITOR REMOVAL
Removal/Access of Monitor and CD Player - Uprights/Cabarets
Monitor Removal
1. Power down the game and unplug the line cord from the power source.
2. Open the rear door to gain access to the monitor section.
3. Disconnect the touchscreen cable and all harnesses. (The touchscreen cable will be attached
to the TTL board (located on the CPU board) or the SMT module, depending on which
controller is used on your game. If your game uses an SMT controller you will have to remove
the screws securing it to the cabinet in order to disconnect the touchscreen cable.)
4. Remove both bolts securing the rear of the monitor shelf to the cabinet. See Figure 1.
5. Open the monitor bezel door.
6. Remove both bolts securing the front of the monitor shelf to the cabinet (located on the
underside of the shelf). See Figure 2.
7. Remove the ground strap attached to the monitor door.
8. Pull the monitor up and out through the monitor bezel door.
FIGURE 1 - UR/CAB - MONITOR REMOVAL
FIGURE 2 - UR/CAB - MONITOR
REMOVAL
