manuals/manuals_Support_Center_manuals_PM0450_04

FIGURE 2 - FORCE FUSION

WITH

ELECTRONICS BOX

AND FUN ZONE

FIGURE 3 - FORCE FUSION

WITHOUT

ELECTRONICS BOX

ELECTRONICS

MOUNTED
DIRECTLY

TO GAME

FIGURE 1 - ION FUSION

Foreseesons 17” Monitor Replacement

CONTENTS:

PM0450-04

MEGATOUCH FORESEESONS MONITOR REPLACEMENT

Fusion and Fun Zone Games

Use the diagrams below to determine your type of game, then follow the appropriate
instructions to remove and install the monitor.

QTY

PART

NUMBER

DESCRIPTION

FUSION MONITOR REPLACEMENT PARTS

EC9384-05

LCD MONITOR

1 MW1379-01

LEFT

BRACKET

1 MW1380-01

RIGHT

BRACKET

4 HW4401

MOUNTING

SCREWS

COUNTERTOP MONITOR REPLACEMENT PARTS

3 HW8811

TIE

WRAP

2 HW8825

TIE

WRAP

2 HW8859-01

SELF-ADHESIVE

CABLE

TIE

WRAP

2 HW6054-01

NYLON

SPACER

2 HW9252-03

VELCRO

PARTS COMMON TO BOTH CABINETS

1 SB0016-01

TOUCHSCREEN

TAPE

KIT

5’ HW8087

FOAM

TAPE

Follow the instructions to remove and install the monitor in your game. For eVo , Elite Edge,
and eVo Wallette games, see page 9.

ELECTRONICS

BOX

ELECTRONICS

BOX

2 MEGATOUCH FORESEESONS MONITOR REPLACEMENT PM0450-04

Fusion with Electronics Box

and Fun Zone Games

Monitor Removal

Turn off and unplug the game.

Unlock and open the bezel.

Force games:

Remove the 6 thumb-

nuts fastening the bezel to the game
(see Figure 4) and remove the bezel.

Ion games:

Disconnect the dongle

wire from the top of the electronics
box and the fast-on connectors from
the coin mech (see Figure 5). Remove
the 6 thumbnuts fastening the bezel to
the game (see Figure 4). Lift up on the
bezel and disconnect the joystick
harness (black, 10-pin connector)
located between the bezel and the
wooden frame. Remove the bezel.

Force games:

Carefully

remove the

screws fastening the touchscreen
controller (see Figure 4) to the game
and

disconnect the cable from the back

of the controller; also disconnect the
ground screw.

Ion games:

Disconnect the touch-

screen controller cable from the
touchscreen controller (see Figure 5).

If you will be reusing the existing
touchscreen, note the orientation of
the screen (i.e. the positioning of the
ribbon cable and which side is the
front) before removing it from the LCD
monitor. Then, use dental floss to
carefully cut the foam tape holding the
touchscreen to the monitor until you are
able to completely remove the screen.
You will need to place the touchscreen
on a stable surface until it is installed
on the new monitor. Then remove any
residual foam tape from the reverse

side of the screen with denatured
alcohol.

Disconnect the VGA monitor
connector, as well as the monitor
power connector and the monitor
control board connector. (For Force
games, see Figure 4; Ion games, see
Figure 5.)

Remove the 4 screws fastening the
monitor to the game (see Figure 6) and
remove it. Be sure to keep track of the
plastic standoffs under the monitor.

Monitor Installation

Line up the monitor’s mounting brack-
ets over the corresponding holes on
the wooden frame and fasten with the
4 screws. If necessary, rotate the
cable clips that are alongside the moni-
tor (they may be in the way of the
brackets). See Figure 6.

Connect the VGA monitor connector
and ground screw, the monitor con-
trol board connector, and the monitor
power connector to the new monitor.
(See Figure 4 for Force games, Figure
5 for Ion games.)

Clean the glass on the new LCD moni-
tor with the supplied alcohol wipe,
then cut pieces of the supplied 1/2”
foam tape long enough to cover each
edge of the monitor without overlap-
ping. After the tape is in place on the
monitor, peel off the backing. Care-
fully place the supplied or existing
touchscreen over the monitor in the
same manner that it was attached to
the old monitor, making sure the
screen is properly and evenly aligned
over the glass.

Force games:

Carefully

connect the

touchscreen cable in the back of the

PM0450-04

MEGATOUCH FORESEESONS MONITOR REPLACEMENT

FIGURE 4 - FORCE FUSION WITH ELECTRONICS BOX - UNDERSIDE OF BEZEL

MONITOR
POWER
CONNECTOR

TOUCHSCREEN
CONTROLLER

TOUCHSCREEN
CONTROLLER
CABLE

VGA

MONITOR

CONNECTOR

THUMBNUTS

SECURING

BEZEL

(6 PLACES)

GROUND

SCREW

MONITOR

CONTROL

BOARD

CONNECTOR

controller (making sure that the cable’s
pins are correctly aligned) and secure
the controller with the existing hard-
ware (Figure 4).

Ion games:

Carefully

connect the

touchscreen cable to the touchscreen
controller (Figure 5), making sure that
the cable’s pins are correctly aligned.
Clean the front of the touchscreen
with the supplied alcohol wipe once it
is in place.

Ion games:

Place the bezel on the

game and reconnect the 10-pin joy-
stick harness between the bezel and
wooden frame, then fasten the bezel
to the frame with the 6 thumbnuts. Re

connect the dongle wire and the coin
mech wires (green wire = COM, white
wire = OPEN). See Figure 5.

Force games:

Secure the bezel to

the game with the 6 thumbnuts.

If there is a gap between the bezel
and the monitor, place foam tape
around the inside edge of the plastic
bezel.

Plug in and turn on the game.

When the game is finished booting,
press the CALIBRATE button.

Close and lock the bezel, then cali-
brate the touchscreen.

4 MEGATOUCH FORESEESONS MONITOR REPLACEMENT PM0450-04

FIGURE 5 - ION FUSION - UNDERSIDE OF BEZEL

MONITOR
POWER
CONNECTOR

TOUCHSCREEN
CONTROLLER

TOUCHSCREEN
CONTROLLER
CABLE

VGA

MONITOR

CONNECTOR

GROUND

SCREW

MONITOR

CONTROL

BOARD

CONNECTOR

DONGLE CABLE
(DISCONNECT END OF CABLE
AT TOP OF ELECTRONICS BOX)

JOYSTICK

CABLE

COIN MECH

SCREWS

FASTENING

MONITOR TO

GAME

(4 PLACES)

FIGURE 6 - MONITOR (WITH BEZEL REMOVED)

PM0450-04

MEGATOUCH FORESEESONS MONITOR REPLACEMENT

Fusion without Electronics

Box

(Force Games Only)

Monitor Removal

Turn off the game and unplug it from
its power source.

Unlock and open the bezel.

Disconnect the VGA monitor connector
and ground screw, the monitor control
board connector, and the monitor
power connector; also remove the
cables from the 2 clamps attached to
the monitor. See Figure 8.

Remove the screws fastening the
touchscreen controller (see Figure 4)
to the game and

carefully

disconnect

the cable from the back of the
controller. Disconnect the ground
screw, and release the cables from
the cable clamps. See Figures 9 and
10.

Remove the 10 screws securing the
plastic bezel to the wooden frame (see
Figure 8) and carefully remove the
bezel from the game. Be careful not
to damage the bezel with the coin cup
during removal.

NOTE: Keep track of all hardware
removed in the monitor replacement
process.

Place the bezel assembly upside down
on a flat surface and remove the 10
screws fastening the LCD monitor to
the bezel (remember which 2 screws
also fasten cable clamps), then remove
the monitor from the bezel and
unscrew the supporting brackets from
the monitor. See Figure 11.

NOTE: Do not scratch the glass when
setting the monitor aside.

If you will be reusing the existing
touchscreen, note the orientation of the
screen (i.e. the positioning of the ribbon
cable and which side is the front)
before removing it from the LCD monitor.
Then, use dental floss to carefully cut
the foam tape holding the screen to the
monitor. You will need to place the
touchscreen on a stable surface until it
is installed on the new monitor. Then
remove any residual foam tape from
the screen with denatured alcohol and
clean the glass with the supplied
alcohol wipe.

Monitor Installation

NOTE: Be sure the monitor glass is not
scratched during installation.

Clean the glass on the new LCD moni-
tor with the supplied alcohol wipe, then
cut pieces of the supplied 1/2” foam
tape long enough to cover each edge
of the monitor without overlapping. Af-
ter the tape is in place on the monitor,
peel off the backing.

Carefully place the supplied or exisitng
touchscreen over the monitor in the
same manner the touchscreen was at-
tached to the old monitor, making sure
the screen is properly and evenly
aligned over the glass. Clean the front
of the touchscreen with the supplied
alcohol wipe once it is in place.

Position the new LCD monitor on the
wooden frame as it will be mounted,
and mark the positions of the 4
mounting screws and 2 cable clamps
(see Figures 7 and 8). Place the
monitor aside and drill holes in the
wooden frame for the screws and
clamps. Reposition the monitor on the
wooden frame and fasten with 4
screws, and replace the 2 cable
clamps in the appropriate screw holes.

6 MEGATOUCH FORESEESONS MONITOR REPLACEMENT PM0450-04

Carefully replace the plastic bezel
assembly in the game, making sure the
coin cup protrudes into the lower
cutout and no wires are pinched, then
secure it to the wooden frame with
the 10 screws (see Figure 8).

If there is a gap between the bezel
and the monitor, place foam tape
around the inside edge of the plastic
bezel.

Carefully

reconnect the touchscreen

controller cable in the back of the
controller and secure the controller in
the game with the existing hardware.
Reattach the ground screw. Replace
the cables in the clamps as before.
See Figures 9 and 10.

Connect the VGA monitor connector
and ground screw (do not over-
tighten), the monitor control board
connector, and the monitor power
connector (see Figure 8) to the new
monitor and replace the cables in the 2
clamps attached to the monitor.

Plug in and turn on the game.

When the game is finished booting,
press the CALIBRATE button.

10. Close and lock the bezel, then calibrate

the touchscreen.

PM0450-04

MEGATOUCH FORESEESONS MONITOR REPLACEMENT

FIGURE 8 - FORCE FUSION WITHOUT ELECTRONICS BOX - UNDERSIDE OF BEZEL

MONITOR
POWER

CONNECTOR

VGA

MONITOR

CONNECTOR

MONITOR

CONTROL

BOARD

CONNECTOR

GROUND

SCREW

SCREWS
SECURING
BEZEL TO

WOODEN
FRAME
(10 PLACES)

CABLE

CLAMPS

(2 PLACES)

FIGURE 9 - FORCE FUSION WITHOUT ELECTRONICS BOX -

TOUCHSCREEN CONTROLLER MOUNTED ON BEZEL

TOUCHSCREEN

CONTROLLER

CONNECTED

TO LCD PANEL

SCREWS

FASTENING

CONTROLLER

TO GAME

(2 PLACES)

MOLEX

CONNECTOR

GROUND

SCREW

FIGURE 10 - FORCE FUSION WITHOUT ELECTRONICS BOX - CLOSEUP OF CPU SECTION

FIGURE 11 - FORCE FUSION WITHOUT ELECTRONICS BOX - UNDERSIDE OF MONITOR

SCREWS
FASTENING
LCD MONITOR
TO BEZEL
(10 PLACES)

CABLE

CLAMPS

FIGURE 12 - FORCE FUSION WITHOUT ELECTRONICS BOX -

PLASTIC MOUNTING PIECES ON BEZEL

DRILLED

HOLES

(5 PER SIDE)

8 MEGATOUCH FORESEESONS MONITOR REPLACEMENT PM0450-04

17” Ion eVo, Elite Edge and
eVo Wallette Games

Monitor Removal

Turn off and unplug the game.

Unlock and open the CPU section.

Very

carefully

cut the tie wraps se-

curing the touchscreen controller cable
to the touchscreen controller. Then,
disconnect the cable from the
touchscreen controller. See Figure 13.

Release the touchscreen controller
ribbon cable from the cable clamp.

Cut the tie wrap securing the
touchscreen controller cables and
speaker wires on the back of the moni-
tor (see Figure 13).

Cut the tie wrap securing the orange
and gray wires and ground wire from
the touchscreen controller and the
OSD cable. See Figure 13.

Remove the touchscreen controller
cable, the orange and gray wires (from
the touchscreen controller) and the
OSD board cable from the cable twist
lock. See Figure 13.

Carefully remove the 2 screws se-
curing the touchscreen controller to
the LCD mounting bracket. Carefully
remove the controller and the nylon
spacers underneath (if applicable).
Set the controller aside.

Disconnect the 2-pin LCD connector,
the OSD connector and the VGA con-
nector from the back of the monitor.
See Figure 13.

PM0450-04

MEGATOUCH FORESEESONS MONITOR REPLACEMENT

FIGURE 13 – FORESEESONS MONITOR IN 17” ION COUNTERTOP GAME

SCREWS

SECURING

LCD BRACKET

TO GAME

(6 PLACES)

OSD BOARD

TOUCHSCREEN
CONTROLLER
CABLE

INVERTER

2-PIN LCD

CONNECTOR

OSD BOARD

CONNECTOR

VGA

CONNECTOR

SCREWS

SECURING THE

MONITOR SIDE

OF HINGE

(3 PER SIDE)

VGA AND

TOUCHSCREEN

CONTROLLER

GROUND WIRES

SECURE STRAIN
RELIEF CORD HERE

CABLE TIE WRAP
SECURING T/S
CONTROLLER
CABLES AND
SPEAKER WIRES

TIE WRAP SECURING
ORANGE AND GRAY
WIRES AND GROUND
WIRE FROM T/S
CONTROLLER AND
OSD CABLE

CABLE TWIST LOCK
SECURING T/S
CONTROLLER CABLE,
ORANGE AND GRAY
WIRES FROM T/S
CONTROLLER, AND
OSD CABLE

TOUCHSCREEN

CONTOLLER

RIBBON CABLE

ROUTED

THROUGH LCD

MOUNTING

BRACKET

CABLE TIE

WRAP

SECURING

VGA CABLE

10. Remove the screw and washer se-

curing the VGA and touchscreen con-
troller ground wires to the back of the
monitor. See Figure 13.

11. Remove the OSD board and inverter

from the Velcro attached to the back
side of the monitor and set them aside.
See Figure 13.

12. Place something in front of the game

to brace the bezel once the strain re-
lief cord is undone, then remove the
screw and washer securing the
strain relief cord. See Figure 13.

13. Remove the remaining 5 screws fas-

tening the LCD mounting bracket to the
game. See Figure 13.

14. Route the touchscreen controller cable

through the hole in the LCD mounting
bracket and set the LCD mounting
bracket aside.

15. Loosen the 6 screws on the monitor

side of the hinges (3 screws per hinge)
in order to raise the hinges and allow
enough room to remove the monitor.
Be careful to keep the hinge spacers
in place beneath the hinges.

16. Carefully remove the monitor from the

bezel.

17. If you will be reusing the existing

touchscreen, note the orientation of
the screen (i.e. the positioning of the
ribbon cable and which side is the
front) before removing it from the LCD
monitor. Then, use dental floss to care-
fully cut the foam tape holding the
touchscreen to the monitor until you are
able to completely remove the screen.
You will need to place the touchscreen
on a stable surface until it is installed
on the new monitor. Then remove any

residual foam tape from the reverse
side of the screen with denatured al-
cohol.

Monitor Installation

18. Clean the glass on the new monitor

with the supplied alcohol wipe, then
cut pieces of the supplied 1/2" foam
tape long enough to cover each edge
of the monitor without overlapping.
After the tape is in place on the moni-
tor, peel off the backing.

19. Carefully place the supplied or exist-

ing touchscreen over the monitor in
the same manner it was attached to
the old monitor, making sure the
screen is properly and evenly aligned
over the glass. Clean the front of the
touchscreen with the supplied alco-
hol wipe once it is in place.

20. Carefully place the new monitor into

the bezel so that the monitor connec-
tions are nearest to the hinges. Make
sure the monitor is properly centered.

21. Route the touchscreen controller cable

through the hole in the LCD mounting
bracket. See Figure 13.

22. Fasten the strain relief cord under the

LCD mounting bracket screw desig-
nated in Figure 13. Replace the re-
maining 5 screws securing the mount-
ing bracket to the bezel. See Figure
13.

23. Tighten the 3 screws per hinge that

were loosened during removal of your
old monitor. See Figure 13. Make sure
the spacers beneath the hinges are
aligned correctly as you tighten the
screws.

24. Carefully attach the cable to the

touchscreen controller, making sure

10 MEGATOUCH FORESEESONS MONITOR REPLACEMENT PM0450-04

PM0450-04

MEGATOUCH FORESEESONS MONITOR REPLACEMENT

that the cable’s pins are correctly
aligned. Secure the cable in place us-
ing the 2 provided black tie wraps.

25. Install the 2 existing nylon spacers on

the standoffs where the touchscreen
controller will be mounted (see Figure
13). If your touchscreen controller did
not have nylon spacers, install the 2
provided spacers. Then, secure the
touchscreen controller to the stand-
offs on the LCD mounting bracket us-
ing the existing screws.

26. Secure the ribbon cable from the

touchscreen controller in the cable
clamp on the LCD mounting bracket.
See Figure 13.

27. Add the “loop” side of the provided

Velcro (the mating side of the Velcro
attached to the OSD board and in-
verter) to the back of the monitor in
the same locations as the old monitor.
Replace the OSD board and inverter
on the Velcro.

28. Connect the 2-pin LCD connector to

the back of the monitor. See Figure
13.

29. Connect the OSD connector to the

monitor. See Figure 13.

30. Connect the VGA monitor connector

to the monitor. See Figure 13.

31. Replace the screw and washer se-

curing the VGA and touchscreen con-
troller ground wires to the back of the
monitor. See Figure 13.

32. Replace the touchscreen controller

cable, the orange and gray wires (from
the touchscreen controller) and the
OSD board cable in the cable twist
lock as shown in Figure 13.

33. Adhere the provided cable tie wraps

to the back of the monitor in the same
locations as the old monitor.

34. Thread the provided tie wrap through

the adhesive cable tie wraps just in-
stalled and secure the touchscreen
controller wires and OSD cable wires
in the cable tie wrap shown in Figure
13. Secure VGA cable in the other
cable tie wrap in the same fashion.

35. Dress the remaining wires using the

supplied tie wrap.

36. Close and lock the CPU section.

37. Plug in and turn on the game.

__________________________________________________________________

_______________________________________________________________

________________________________________________________________

___________________________________________________________________

_______________________________________________________________

________________________________________________________________

__________________________________________________________________

_________________________________________________________________

______________________________________________________________

________________________________________________________________

___________________________________________________________________

__________________________________________________________________

_________________________________________________________________

_____________________________________________________________________

___________________________________________________________________

__________________________________________________________________

___________________________________________________________________

__________________________________________________________________

________________________________________________________________

_________________________________________________________________