manuals/manuals_Support_Center_manuals_PM0450_03

Megatouch FORCE Fusion Monitor Replacement

CONTENTS:

FIGURE 1 - FUSION WITH

ELECTRONICS BOX

Use the diagrams below to determine your type of game, then follow the appropriate

instructions to remove and install the monitor.

FIGURE 2 - FUSION WITHOUT

ELECTRONICS BOX

QTY

PART NUMBER

DESCRIPTION

SA0469-03

LCD MONITOR W/ SIDE BRACKETS,
TOUCHSCREEN

SA0469-04

LCD MONITOR W/ SIDE BRACKETS ONLY

SB0016-01

TOUCHSCREEN TAPE KIT

SA0469-09

LCD MONITOR W/ TOUCHSCREEN

EC9384-02

LCD MONITOR ONLY

SB0016-01

TOUCHSCREEN TAPE KIT

ELECTRONICS

MOUNTED
DIRECTLY

TO GAME

ELECTRONICS

BOX

PM0450-03

MEGATOUCH FORCE FUSION MONITOR REPLACEMENT

Fusion with Electronics Box

Removing the Monitor

Turn off and unplug the game.

Unlock and open the bezel.

Remove the 6 thumbnuts fastening the

bezel to the game (see Figure 3) and

remove the bezel.

If you will not be reusing the existing

touchscreen, remove the cable clamps

securing the touchscreen cable and the

touchscreen power harness, then

remove the screws fastening the

touchscreen controller (see Figure 3)

to the game and disconnect the cable

from the back of the controller. Locate

and disconnect the Molex connector

(orange and gray wires) running from

the touchscreen controller cable to the

main power harness, and also

disconnect the ground screw. See

Figure 3.

If you will be reusing the existing

touchscreen, disconnect the touch-

screen controller cable from the LCD

panel (see Figure 3). Then use dental

floss to carefully cut the foam tape

holding the touchscreen to the monitor

until you are able to completely remove

the screen. You will need to place the

touchscreen on a stable surface until

it is installed on the new monitor. Then

remove any residual foam tape from

the reverse side of the screen with

denatured alcohol.

Disconnect the VGA monitor connector

and ground screw, as well as the

monitor power connector. Standard

monitors only: Also disconnect the

monitor control board connector. See

Figure 3.

Remove the 4 screws fastening the

monitor to the game (see Figure 4) and

remove it. Be sure to keep track of the

plastic standoffs under the monitor.

Installing the Monitor

With the plastic standoffs in place, in-

stall the new monitor in the game and

fasten it with the 4 screws (see Fig-

ure 4).

Connect the VGA monitor connector

and ground screw, the monitor con-

trol board connector, and the monitor

power connector to the new monitor.

See Figure 3.

If your replacement monitor already

has a touchscreen, connect the

touchscreen cable in the back of the

controller and secure the controller with

the existing hardware. Also connect

the Molex connector (orange and gray

wires) to the main power harness (af-

ter routing the wires through the cable

clamps) and attach the ground screw.

See Figure 3.

If you are using the original touch-

screen, clean the glass on the new

LCD monitor with the supplied alcohol

wipe, then cut pieces of the supplied

1/2” foam tape long enough to cover

each edge of the monitor without over-

lapping. After the tape is in place on

the monitor, peel off the backing. Care-

fully place the touchscreen over the

monitor in the same manner it was at-

tached to the old monitor, making sure

the screen is properly and evenly

aligned over the glass, then connect

the cable to the LCD panel (see Figure

3). Clean the front of the touchscreen

with the supplied alcohol wipe once it

is in place.

2 MEGATOUCH FORCE FUSION MONITOR REPLACEMENT PM0450-03

FIGURE 3 - FUSION WITH ELECTRONICS BOX - UNDERSIDE OF BEZEL

PM0450-03

MEGATOUCH FORCE FUSION MONITOR REPLACEMENT

Reinstall the bezel on the game and

fasten it with the 6 thumbnuts.

Plug in and turn on the game.

MONITOR
POWER
CONNECTOR

TOUCHSCREEN
CONTROLLER
CABLE
CONNECTED TO
LCD PANEL

TOUCHSCREEN
CONTROLLER

VGA

MONITOR

CONNECTOR

THUMBNUTS

SECURING

BEZEL

(6 PLACES)

GROUND

SCREW

MONITOR

CONTROL

BOARD

CONNECTOR

When the game is finished booting,

press the CALIBRATE button.

Close and lock the bezel, then cali-

brate the touchscreen.

4 MEGATOUCH FORCE FUSION MONITOR REPLACEMENT PM0450-03

SCREWS

FASTENING

MONITOR
TO GAME

(4 PLACES)

FIGURE 4 - FUSION WITH ELECTRONICS BOX - MONITOR (WITH BEZEL REMOVED)

Fusion without
Electronics Box

Removing the Monitor

Turn off the game and unplug it from

its power source.

Unlock and open the bezel.

Disconnect the VGA monitor connector

and ground screw, the monitor control

board connector, and the monitor

power connector and also remove the

cables from the 2 clamps attached to

the monitor. See Figure 5.

If you will not be reusing the existing

touchscreen, remove the screws

fastening the touchscreen controller to

the game and disconnect the cable

from the back of the controller. Then

locate and disconnect the Molex

connector (orange and gray wires)

running from the touchscreen controller

cable to the main power harness. After

disconnecting the ground screw, pull

the cables out of the clamps. See

Figures 6 and 7.

If you will be reusing the existing

touchscreen, disconnect the touch-

screen controller cable from the LCD

panel (see Figure 6).

Remove the 10 screws securing the

plastic bezel to the wooden frame (see

Figure 5) and carefully remove the

bezel from the game. Be careful not

to damage the bezel with the coin cup

during removal.

NOTE: Keep track of all hardware
removed in the monitor replacement
process.

Place the bezel assembly upside-

down on a flat surface and remove

the 10 screws fastening the LCD

monitor to the bezel (remember which

2 screws also fasten cable clamps),

then remove the monitor from the

bezel. See Figure 8.

NOTE: Be sure the glass is not
scratched when setting the monitor
aside.

PM0450-03

MEGATOUCH FORCE FUSION MONITOR REPLACEMENT

If you will not be reusing the existing

touchscreen, skip to the next step. If

you will be reusing the touchscreen,

note the orientation of the screen (i.e.,

the positioning of the ribbon cable and

which side is the front) before

removing it from the LCD monitor. Then

use dental floss to carefully cut the

foam tape holding the screen to the

monitor. Once the touchscreen is

completely free from the monitor,

remove any residual foam tape from

the screen with denatured alcohol and

clean the glass with the supplied

alcohol wipe.

Installing the Monitor

NOTE: Be sure the monitor glass is not
scratched during installation.

If your replacement monitor already

has a touchscreen, skip to step 3. If

you will be using the original touch-

screen, clean the glass on the new

LCD monitor with the supplied alcohol

wipe, then cut pieces of the supplied

1/2” foam tape long enough to cover

each edge of the monitor without over-

lapping. After the tape is in place on

the monitor, peel off the backing.

Carefully place the touchscreen over

the monitor in the same manner it was

attached to the old monitor, making sure

the screen is properly and evenly

aligned over the glass. Clean the front

of the touchscreen with the supplied

alcohol wipe once it is in place.

Place the new LCD monitor in the bezel

(make sure it is not upside-down), lining

up the screw holes on the face of the

mounting frame with the larger, drilled

holes on the plastic mounting pieces

(see Figure 9), and fasten it with the

10 screws. Also replace the cable

clamps in the appropriate screw holes.

See Figure 8.

Carefully replace the plastic bezel

assembly in the game, making sure the

coin cup protrudes into the lower

cutout and no wires are pinched, then

secure it to the wooden frame with

the 10 screws (see Figure 5).

If the monitor has a new touchscreen,

connect the touchscreen controller

cable in the back of the controller and

secure the controller in the game with

the existing hardware. Then connect

the Molex connector (orange and gray

wires) to the main power harness and

attach the ground screw. Replace the

cables in the clamps as before. See

Figure 7.

If the monitor has the original touch-

screen, reconnect the touchscreen

controller cable to the LCD panel (see

Figure 6).

Connect the VGA monitor connector

and ground screw (do not over-

tighten), the monitor control board

connector, and the monitor power

connector (see Figure 5) to the new

monitor and replace the cables in the

2 clamps attached to the monitor.

Plug in and turn on the game.

When the game is finished booting,

press the CALIBRATE button.

Close and lock the bezel, then cali-

brate the touchscreen.