manuals/manuals_Support_Center_manuals_PM0331_05

Table of Contents

FORCE GAMES

Force eVo, eVo Wallette & Elite Edge

Touchscreen Removal ................ p. 1
Touchscreen Installation ............ p. 1-2

Force Radion & Fun Zone Jr.

Touchscreen Removal ................ p. 2-4
Touchscreen Installation ............ p. 4

Force Classic

Touchscreen Removal ................ p. 5
Touchscreen Installation ............ p. 5-6

Force Elite

Touchscreen Removal ................ p. 7
Touchscreen Installation ............ p. 8

Force Vibe

Touchscreen Removal ................ p. 9-10
Touchscreen Installation ............ p. 10

Force Fusion (with electronics box)
& Fun Zone

Touchscreen Removal ................ p. 11
Touchscreen Installation ............ p. 12

Force Fusion
(without electronics box)

Touchscreen Removal ................ p. 13-14
Touchscreen Installation ............ p. 15

Force Upright (Non-Fusion)

Touchscreen Removal ................ p. 16
Touchscreen Installation ............ p. 17

Megatouch Combo Jukebox

Touchscreen Removal ................ p. 17-18
Touchscreen Installation ............ p. 19

Mr VIPS

Touchscreen Removal ................ p. 20-23
Touchscreen Installation ............ p. 24-25

ION GAMES

Ion eVo, eVo Wallette, Megatouch
Entertainer & Elite Edge

Touchscreen Removal .................. p. 26-27
Touchscreen Installation .............. p. 28

Ion Aurora

Touchscreen Removal .................. p. 29-33
Touchscreen Installation .............. p. 34-35

Ion Fusion

Touchscreen Removal .................. p. 36
Touchscreen Installation .............. p. 37

FIGURE 1 - FORCE EVO/EVO WALLETTE - MONITOR REMOVAL

SCREWS

FASTENING

LCD

MOUNTING

BRACKET

TO GAME

(6 PLACES)

STRAIN

RELIEF

CORD

1 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

FORCE EVO, EVO WALLETTE
AND ELITE EDGE GAMES

Touchscreen Removal

Turn off and unplug the game.

Unlock and open the CPU section and
place something under the front bezel
to brace it when the strain relief cord is
disconnected.

Remove the two screws securing the
touchscreen controller to the game,
then disconnect the cable from the back
of the controller. Also disconnect the
Molex connector (orange and gray
wires) running from the touchscreen
controller cable to the main power har-
ness.

Megatouch Touchscreen Replacement

CONTENTS:

Remove the (6) screws fastening the
LCD mounting bracket to the game (one
screw also fastens the strain relief
cord) and remove the bracket. See
Figure 1.

Disconnect all connections to the LCD
monitor until you’re able to slide the
monitor out of the game.

Remove any remaining adhesive resi-
due with denatured alcohol, then clean
the monitor glass with the supplied al-
cohol wipe.

QTY PART

NUMBER

DESCRIPTION

HW8087

3/8”W X 3/16”T FOAM TAPE

HW8067-02

3/8”W X 1/8”T FOAM TAPE

HW8067

1/2”W X 1/32”T FOAM TAPE

HW8086

1/2”W X 1/16”T FOAM TAPE (SINGLE SIDED)

1 HW8078 1”W

POLYESTER

TAPE

1 HW8061-01

ALCOHOL

WIPE

Touchscreen Installation

Clean the reverse side of the replace-
ment touchscreen with the supplied al-
cohol wipe.

Cut pieces of the supplied 1/2” double-
sided foam tape long enough to cover
each edge of the screen without over-
lapping. After the tape is in place on
the screen, peel off the backing.

10. Replace the new touchscreen over the

monitor in the same manner as the old
screen, making sure the screen is prop-
erly and evenly aligned over the moni-
tor glass. Then clean the front of the
screen with the supplied alcohol wipe.

11. Slide the LCD monitor assembly back

into the game and reconnect all cables
to the monitor.

12. Replace the LCD mounting bracket in

the game and fasten it with the 6
screws removed earlier. Also refas-
ten the strain relief cord.

13. Connect the new touchscreen control-

ler cable in the back of the controller
and secure the controller in the game
with the existing hardware. Also
connect the Molex connector (orange
and gray wires) to the main power
harness.

14. Plug in and turn on the game.

15. Once the game has booted up, press

the “Calib” button on the OSD board
and perform a touchscreen calibration.
Then, ensure that the screen is prop-
erly aligned, and make any necessary
adjustments with the monitor controls
on the OSD board.

16. Close and lock the CPU section.

FORCE RADION/
FUN ZONE JR. GAMES

Touchscreen Removal

Turn off and unplug the game.

Unlock and open both side doors and
the rear door.

Remove the cash box.

Remove the screw securing the strain
relief cord to the rear door, then re-
move the monitor board from the velcro
on the rear door.

Remove the screws holding the rear
bezel to the game. Five screws are
located along the top edge of the game
and 2 are at the bottom rear of each
side of the game. See Figure 2.

Lift the rear bezel from the game.

Remove the 4 screws holding the front
bezel to the game. Two screws are
located at the bottom on each side of
the game (see Figure 2) and 2 are on
the top surface (see Figure 3).

Lift the front bezel from the game.

Remove the two nuts and washers
securing the touchscreen controller
(see Figure 3) to the game and remove
the controller from the mounting
screws. Then disconnect the cable
from the back of the controller and dis-
connect the Molex connector (orange
and gray wires) running from the
touchscreen controller cable to the main
power harness.

10. Remove the black poly tape from around

the edges of the old touchscreen. Re-
member how the tape was placed in
order to tape the new touchscreen.

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 2

3 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

FIGURE 3 - FORCE RADION/FUN ZONE JR. - MONITOR ASSEMBLY

FIGURE 2 - FORCE RADION/FUN ZONE JR. - FRONT AND REAR BEZELS

REPLACEMENT

TOUCHSCREEN

PICTURE

TUBE

SCREWS SECURING
FRONT BEZEL
(2 PLACES)

TOUCHSCREEN
CONTROLLER

SCREW
SECURING
REAR BEZEL
(BOTH SIDES)

SCREW
SECURING
FRONT BEZEL
(BOTH SIDES)

SCREWS SECURING REAR
BEZEL (5 PLACES)

11. Use dental floss to carefully cut the

foam tape holding the touchscreen to
the picture tube until you are able to
completely remove the touchscreen.

12. Remove any remaining adhesive resi-

due with denatured alcohol, then wipe
the surface of the picture tube with the
supplied alcohol wipe.

Touchscreen Installation

13. Clean the reverse side of the replace-

ment touchscreen with the supplied al-
cohol wipe.

14. Peel the backing from the 8 pieces of

foam tape already adhered to the re-
verse side of the touchscreen. Then
cut 8 pieces of equal size from the sup-
plied roll of 3/8” double-sided foam tape
(the thinner of the two supplied 3/8”
rolls) and place them (backing side fac-
ing out) on the tape already on the
touchscreen before peeling off the
backing. The double-thickness of the
foam tape will allow enough distance
between the touchscreen and the pic-
ture tube once the new screen is in
place.

15. Replace the new touchscreen over the

picture tube (with the cable on the left
if you are facing the game), making sure
the screen is properly and evenly
aligned over the picture tube. Then
clean the front of the screen with the
supplied alcohol wipe.

16. Connect the new touchscreen control-

ler cable in the back of the controller
and secure the controller on the mount-
ing screws in the game with the exist-
ing hardware. Also connect the Molex
connector (orange and gray wires) to
the main power harness.

17. Remembering the manner in which the

tape was placed around the touch-
screen you removed, place and cut a
length of the supplied black poly tape
evenly over an entire edge of the touch-
screen and repeat until all 4 edges are
covered.

18. Place and cut a longer length of black

poly tape around all 4 edges of the
screen.

NOTE: Use the additional 3/8” foam
tape (the thicker of the two supplied
3/8” rolls) if you need to replace the
gasket on the inside of the front bezel.
Be sure to remove all of the existing
foam tape and adhesive first.

19. Replace the front bezel and the 4

screws (2 at the bottom, 2 at the top)
holding the bezel to the game. See Fig-
ures 2 and 3.

20. Replace the rear bezel and the 7

screws (5 along the top edge, 2 at the
bottom rear) holding the bezel to the
game. See Figure 2.

21. Replace the screw securing the strain

relief cord to the rear door, then re-
place the monitor board.

22. Replace the cash box.

24. Plug in and turn on the game.

25. When the game is finished booting, cali-

brate the touchscreen. Then, ensure
that the screen is properly aligned, and
make any necessary adjustments with
the monitor control board.

26. Close and lock the rear door, then re-

place and lock both side doors.

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 4

FORCE CLASSIC GAMES

Touchscreen Removal

Turn off and unplug the game.

Unlock and remove the coin box or coin
box/bill acceptor assembly.

Unlock and open the rear door. To re-
move the lid, first disconnect the fan
power connector, then the clear drain-
age tubing (from lid end) and ground
strap. Also remove the monitor control
board attached with velcro to the in-
side of the game. Then press up on
the spring-loaded levers (located on
each side of the lid), push the levers
forward, and lift and remove the lid.
Remove the front bezel. See Figures 4
and 5.

Remove the 2 nuts and washers se-
curing the touchscreen controller to the
game, and remove the controller from
the mounting screws. Then discon-
nect the touchscreen controller cable

from the back of the controller and dis-
connect the Molex connector (orange
and gray wires) running from the
touchscreen controller cable to the main
power harness.

Remove the black poly tape from around
the edges of the old touchscreen. Re-
member how the tape was placed in
order to tape the new touchscreen.

Use dental floss to carefully cut the
foam tape holding the touchscreen to
the picture tube until you are able to
completely remove the touchscreen.

Remove any remaining adhesive resi-
due with denatured alcohol, then wipe
the surface of the picture tube with the
supplied alcohol wipe.

Touchscreen Installation

Clean the reverse side of the replace-
ment touchscreen with the supplied
alcohol wipe.

GROUND

STRAP

FAN POWER

CONNECTOR

CLEAR DRAINAGE
TUBING

SPRING-LOADED

LEVER

FIGURE 4 - FORCE CLASSIC - HOOD ASSEMBLY

5 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

FIGURE 5 - FORCE CLASSIC - MONITOR ASSEMBLY

FRONT

BEZEL

If there is no tape already on the screen,
cut pieces of the supplied 1/2” double-
sided foam tape long enough to cover
each edge of the screen without over-
lapping. After the tape is in place on
the screen, peel off the backing.

10. Replace the new touchscreen over the

picture tube (with the cable on the right
if you are facing the game), making sure
the screen is properly and evenly
aligned over the picture tube. Then
clean the front of the screen with the
supplied alcohol wipe.

11. Remembering the manner in which the

tape was placed around the touch-
screen you removed, place and cut a
length of the supplied black poly tape
evenly over an entire edge of the touch-
screen and repeat until all 4 edges are
covered.

12. Place and cut a longer length of black

poly tape around all 4 edges of the
screen.

13. Route the new touchscreen controller

cable under the picture tube and away
from the flyback transformer. Then re-
connect the cable in the back of the

controller and secure the controller on
the mounting screws in the game with
the existing hardware. Also connect
the Molex connector (orange and gray
wires) to the main power harness.

NOTE: Use the supplied roll of 3/8”
foam tape (the thicker of the two 3/8”
rolls) if you need to replace the gasket
on the inside of the front bezel. Be sure
to remove all of the existing foam tape
and adhesive first.

14. After replacing the front bezel, install

the hood on the chassis, connecting
the fan power connector, monitor con-
trol board, ground strap, and plastic
drain tube. See Figure 4 for locations.
Pull the hood towards you until the
spring-loaded levers lock into place.

15. Close and lock the hood.

16. Plug in and turn on the game.

17. When the game is finished booting, cali-

brate the touchscreen. Then, ensure
that the screen is properly aligned, and
make any necessary adjustments with
the monitor control board.

18. Replace and lock the coin box or coin

box/bill acceptor assembly.

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 6

FIGURE 6 - FORCE ELITE - SIDE PANEL LATCH ACCESS

SIDE PANEL

LATCHES

LATCH DETAIL

FORCE ELITE GAMES

Touchscreen Removal

Turn off and unplug the game.

Unlock and open the rear door.

Disconnect the monitor power connec-
tion (black and yellow wires) running
to the power supply.

Disconnect the monitor signal cable
from the motherboard and remove it
from the cable clamps.

Inside the game, access the latches
for each side panel and remove both
panels (see Figure 6).

Remove the 2 nuts and washers se-
curing the touchscreen controller to the
game and remove the controller from
the mounting screws. Then discon-
nect the cable from the back of the
controller and disconnect the Molex
connector (orange and gray wires)
running from the touchscreen control-
ler cable to the main power harness.

Remove the 3 screws at the top of each
side piece fastening the top cover to
the game (see Figure 7) and remove
the top cover.

Loosen the 5/16” nuts securing the 2
LCD clips (one on each side piece).
See Figure 7.

Lift the bezel and monitor assembly from
the game.

10. Remove the 3 screws on top of the

front bezel (see Figure 7) and sepa-
rate the bezel from the monitor.

11. Use dental floss to carefully cut the

foam tape holding the touchscreen to
the monitor until you are able to com-
pletely remove the touchscreen.

12. Remove any remaining adhesive resi-

due with denatured alcohol, then clean
the monitor glass with the supplied al-
cohol wipe.

7 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

FIGURE 7 - FORCE ELITE - FRONT BEZEL REMOVAL

NUTS FASTENING
LCD CLIPS
(BOTH SIDES)

SCREWS SECURING
TOP COVER
(BOTH SIDES)

SCREWS SECURING

BEZEL (3 PLACES)

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 8

Touchscreen Installation

13. Clean the reverse side of the replace-

ment touchscreen with the supplied al-
cohol wipe.

14. Cut pieces of the supplied 1/2” double-

sided foam tape long enough to cover
each edge of the screen without over-
lapping. After the tape is in place on
the screen, peel off the backing.

15. Replace the new touchscreen over the

monitor (with the cable on the left if
you are facing the game), making sure
the screen is properly and evenly
aligned over the monitor glass. Then
clean the front of the screen with the
supplied alcohol wipe.

16. Reattach the front bezel to the monitor

with the 3 screws removed earlier. See
Figure 7.

17. Replace the monitor assembly, aligning

it with the support brackets inside the
game and making sure the LCD clips fit
properly into the slots at the top of each
side.

18. Tighten the nuts securing the 2 LCD

clips. See Figure 7.

19. Replace the top cover.

20. Replace the 3 screws at the top of each

side piece. The shorter screw will go
in the screw hole closest to the rear of
the game. See Figure 7.

21. Connect the new touchscreen control-

22. Replace both side panels.

23. Reconnect the monitor power connec-

tor to the power supply.

24. Route the monitor signal connector

through the cable clamps and recon-
nect it to the motherboard.

25. Plug in and turn on the game.

26. When the game is finished booting, cali-

brate the touchscreen. Then, ensure
that the screen is properly aligned, and
make any necessary adjustments with
the monitor control board.

27. Close and lock the rear door.

FORCE VIBE GAMES

Touchscreen Removal

Turn off and unplug the game.

Unlock and open the CPU section.

Games with bill acceptors only:

Remove the clamp fastening the bill ac-
ceptor sensor cable to the VGA moni-
tor cable. Then disconnect the 12-pin
power connector from the side of the
bill acceptor and remove the 4 screws
and washers securing the bill accep-
tor to the CPU. You will then be able to
remove the bill acceptor.

Disconnect the VGA monitor cable con-
nector and the screw fastening the
cable to the monitor mounting plate, and
also disconnect the ground screw.
Then disconnect the monitor power
connector. See Figure 8.

Remove the 2 thumbnuts securing the
touchscreen controller to the game and
remove the controller from the mount-
ing screws. Then disconnect the cable

from the back of the controller and dis-
connect the Molex connector (orange
and gray wires) running from the
touchscreen controller cable to the main
power harness. Also disconnect the
ground screw. See Figure 8.

Using Figure 8, remove the 10 screws
fastening the monitor to the bezel (2
screws also fasten strain relief cords
on either side of the CPU) and carefully
pull the monitor assembly away from
the bezel until you’re able to access
the touchscreen.

NOTE: Keep track of all hardware
removed in the touchscreen
replacement process.

Note the orientation of the touchscreen
cable before removing the screen.
Then use dental floss to carefully cut
the foam tape holding the touchscreen
to the monitor until you are able to com-
pletely remove the screen. Note the
manner in which the 2 layers of foam
tape are placed on the front edge of
the screen.

SCREWS

FASTENING

MONITOR TO

BEZEL

(10 PLACES)

TOUCHSCREEN

POWER

CONNECTOR

TOUCHSCREEN
CONTROLLER

GROUND
SCREW

MONITOR

POWER

CONNECTOR

VGA

MONITOR

CONNECTOR

FIGURE 8 - FORCE VIBE - MONITOR REMOVAL

9 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

Remove any remaining adhesive resi-
due with denatured alcohol, then clean
the monitor glass with the supplied al-
cohol wipe.

Touchscreen Installation

Clean the reverse side of the replace-
ment touchscreen with the supplied al-
cohol wipe.

10. If there is no tape already on the touch-

screen, cut pieces of the supplied 1/2”
double-sided foam tape long enough to
cover each edge of the screen with-
out overlapping. After the tape is in
place on the screen, peel off the back-
ing.

11. Replace the new touchscreen over the

monitor in the same manner as the old
screen, making sure the screen is prop-
erly and evenly aligned over the moni-
tor glass. Then clean the front of the
screen with the supplied alcohol wipe.

12. Using the original touchscreen for ref-

erence, cut pieces of the supplied 1/2”
single-sided foam tape long enough to
cover each edge of the front of the
screen without overlapping, then place
the tape on the screen. After the tape
is in place, repeat this step so there
are two layers of tape on the screen.

13. Connect the new touchscreen control-

14. Replace the monitor assembly in the

bezel, lining up the screw holes in the
monitor with the holes in the bezel, then
replace the 10 screws. See Figure 8.

15. Reconnect the VGA monitor cable con-

nector and the screw fastening the
cable to the monitor mounting plate, and
also reconnect the ground screw. Then
reconnect the monitor power connec-
tor. See Figure 8.

16.

Games with bill acceptors only:

Replace the bill acceptor in the CPU
section (make sure the touchscreen
controller cables do not interfere) and
fasten it with the 4 screws and wash-
ers. Then reconnect the 12-pin bill ac-
ceptor power connector. It is also rec-
ommended you use a cable clamp to
refasten the bill acceptor sensor and
VGA monitor cables.

17. Plug in and turn on the game.

18. When the game is finished booting, cali-

brate the touchscreen. Then, ensure
that the screen is properly aligned, and
make any necessary adjustments with
the monitor control board.

19. Close and lock the CPU section.

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 10

11 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

FORCE FUSION/
FUN ZONE GAMES

Use Figures 9 and 10 to determine your
type of game, then follow the appropriate
instructions to remove and install the
touchscreen.

Fusion with electronics box/
Fun Zone

Touchscreen Removal

Turn off and unplug the game.

Unlock and open the bezel.

Remove the 6 thumbnuts fastening the
bezel to the game (see Figure 11) and
remove the bezel.

Remove the cable clamps securing the
touchscreen cable and the
touchscreen power harness, then
remove the screws fastening the
touchscreen controller (see Figure 11)
to the game and disconnect the cable
from the back of the controller. Locate
and disconnect the Molex connector
(orange and gray wires) running from
the touchscreen controller cable to the
main power harness, and also
disconnect the ground screw.

Use dental floss to carefully cut the
foam tape holding the touchscreen to
the monitor until you are able to
completely remove the screen. Once
the touchscreen is completely free
from the monitor, remove any residual
foam tape from the monitor with
denatured alcohol.

FIGURE 9 - FUSION WITH

ELECTRONICS BOX/FUN ZONE

FIGURE 10 - FUSION WITHOUT

ELECTRONICS BOX

ELECTRONICS

MOUNTED

DIRECTLY

TO GAME

ELECTRONICS

BOX

Touchscreen Installation

Clean the glass on the reverse side of
the new touchscreen with the sup-
plied alcohol wipe, then cut pieces of
the supplied 1/2” foam tape long
enough to cover each edge of the
monitor without overlapping. After the
tape is in place on the monitor, peel off
the backing. Carefully place the
touchscreen over the monitor in the
same manner it was attached to the
old monitor, making sure the screen is
properly and evenly aligned over the
glass. Clean the front of the
touchscreen with the supplied alco-
hol wipe once it is in place.

Connect the touchscreen cable in the
back of the controller (see Figure 11)

FIGURE 11 - UNDERSIDE OF BEZEL

and secure the controller with the ex-
isting hardware. Also connect the
Molex connector (orange and gray
wires) to the main power harness (af-
ter routing the wires through the cable
clamps) and attach the ground screw.

Reinstall the bezel on the game and
fasten it with the 6 thumbnuts.

Plug in and turn on the game.

10. When the game is finished booting, cali-

brate the touchscreen. Then, ensure
that the screen is properly aligned, and
make any necessary adjustments with
the monitor control board.

11. Close and lock the bezel, then cali-

brate the touchscreen.

TOUCHSCREEN
CONTROLLER

THUMBNUTS

SECURING

BEZEL

(6 PLACES)

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 12

FIGURE 12 - FORCE FUSION - UNDERSIDE OF BEZEL

MONITOR
POWER

CONNECTOR

VGA

MONITOR

CONNECTOR

MONITOR

CONTROL

BOARD

CONNECTOR

GROUND

SCREW

SCREWS
SECURING
BEZEL TO

WOODEN
FRAME
(10 PLACES)

CABLE

CLAMPS

(2 PLACES)

TOUCHSCREEN

CONTROLLER

13 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

Fusion without electronics box

Touchscreen Removal

Turn off and unplug the game.

Unlock and open the bezel.

Disconnect the VGA monitor connector
and ground screw, the monitor control
board connector, and the monitor
power connector and also remove the
cables from the 2 clamps attached to
the monitor. See Figure 12.

Remove the screws fastening the
touchscreen controller to the game and
disconnect the cable from the back of
the controller. Then locate and

disconnect the Molex connector
(orange and gray wires) running from
the touchscreen controller cable to the
main power harness. After
disconnecting the ground screw, pull
the cables out of the clamps. See
Figures 12 and 13.

Remove the 10 screws securing the
plastic bezel to the wooden frame (see
Figure 12) and carefully remove the
bezel from the game. Be careful not
to damage the bezel with the coin cup
during removal.

NOTE: Keep track of all hardware
removed in the touchscreen
replacement process.

MOLEX

CONNECTOR

GROUND

SCREW

FIGURE 13 - FORCE FUSION - CLOSEUP OF CPU SECTION

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 14

FIGURE 14 - FORCE FUSION - UNDER SIDE OF MONITOR

SCREWS

FASTENING

LCD MONITOR

TO BEZEL

(10 PLACES)

CABLE
CLAMPS

Place the bezel assembly upside-
down on a flat surface and remove
the 10 screws fastening the LCD
monitor to the bezel (remember which
2 screws also fasten cable clamps),
then remove the monitor from the
bezel. See Figure 14.

NOTE: Be sure not to scratch the glass
when setting the monitor aside.

Note the orientation of the touchscreen
cable before removing the screen.
Then use dental floss to carefully cut
the foam tape holding the touchscreen
to the monitor until you are able to com-
pletely remove the screen. Once the
touchscreen is completely free from
the monitor, remove any residual foam
tape from the monitor with denatured
alcohol.

FIGURE 15 - FORCE FUSION - PLASTIC MOUNTING PIECES ON BEZEL

DRILLED

HOLES

(5 PER SIDE)

15 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

Touchscreen Installation

Carefully place the touchscreen over
the monitor in the same manner as the
old screen, making sure the screen is
properly and evenly aligned over the
glass. Then clean the front of the
screen with the supplied alcohol wipe.

10. Place the new LCD monitor in the bezel

(make sure it is not upside-down), lining
up the screw holes on the face of the
mounting frame with the larger, drilled
holes on the plastic mounting pieces
(see Figure 15), and fasten it with the
10 screws. Also replace the cable
clamps in the appropriate screw holes
(See Figure 14).

11. Carefully replace the plastic bezel

assembly in the game, making sure the
coin cup protrudes into the lower

cutout and no wires are pinched, then
secure it to the wooden frame with
the 10 screws (see Figure 12).

12. Connect the touchscreen controller

cable in the back of the controller and
secure the controller in the game with
the existing hardware. Then connect
the Molex connector (orange and gray
wires) to the main power harness and
attach the ground screw. Replace the
cables in the clamps as before. See
Figure 13.

13. Reconnect the VGA monitor connector

and ground screw (do not
overtighten), the monitor control board
connector, and the monitor power
connector (see Figure 12) and replace
the cables in the 2 clamps attached to
the monitor.

14. Plug in and turn on the game.

15. When the game is finished booting, cali-

brate the touchscreen. Then, ensure
that the screen is properly aligned, and
make any necessary adjustments with
the monitor control board.

16. Close and lock the bezel, then cali-

brate the touchscreen.

BLACK POLY TAPE

Remove the black poly tape (see Fig-
ure 16) from around the edges of the
old touchscreen, keeping the manner
in which the tape was placed around
the screen in mind.

Use dental floss to carefully cut the
foam tape holding the touchscreen to
the picture tube until you are able to
completely remove the touchscreen.

Remove any remaining adhesive resi-
due with denatured alcohol, then wipe
the surface of the picture tube with the
supplied alcohol wipe.

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 16

FORCE UPRIGHT (NON-FUSION)
GAMES

Touchscreen Removal

Turn off and unplug the game.

Upright with coin door:

Remove the

bezel by removing the 2 wing nuts in-
side the CPU door along the bottom of
the bezel and the 3 wing nuts inside
the game along the top piece (after re-
moving the rear door). Then discon-
nect the 2 speaker connectors inside
the game on either side of the marquee
before lifting the bezel from the game.

Upright without coin door:

Unlock

and open the front bezel (see Figure
16).

FIGURE 16 - FORCE UPRIGHT (NON-FUSION) TOUCHSCREEN ACCESS

Touchscreen Installation

Clean the reverse side of the replace-
ment touchscreen with the supplied al-
cohol wipe.

Peel the backing from the 8 pieces of
double-sided foam tape already ad-
hered to the reverse side of the
touchscreen.

Replace the new touchscreen over the
picture tube (with the cable on the right
if you are facing the game), making sure
the screen is properly and evenly
aligned over the picture tube. Then
clean the front of the screen with the
supplied alcohol wipe.

10. Connect the new touchscreen control-

11. Remembering the manner in which the

tape was placed around the touch-
screen you removed, place and cut a
length of the supplied black poly tape
evenly over an entire edge of the touch-
screen and repeat until all 4 edges are
covered.

12. Place and cut a longer length of black

poly tape around all 4 edges of the
screen.

13. Plug in and turn on the game.

14. When the game is finished booting, cali-

brate the touchscreen. Then, ensure
that the screen is properly aligned, and
make any necessary adjustments with
the monitor control board.

15. Close and lock the front bezel. For

upright games with coin doors, replace

the bezel and secure it with the 5 wing
nuts removed earlier. Also reconnect
the 2 speaker connectors, then replace
the rear door.

MEGATOUCH COMBO JUKEBOX

Touchscreen Removal

Turn off and unplug the game.

Unlock and remove the rear door and
turn off the internal power switch (lo-
cated above the cooling fan on the left
side).

Using Figures 17 and 18, remove the 6
bolts and wing nuts (3 per side) fas-
tening the front bezel to the cabinet and
remove the bezel.

Using Figure 19, locate the
touchscreen controller mounted inside
the cabinet on the right side (if you are
facing the rear of the game) and re-
move the two screws fastening the
controller to the cabinet. Then discon-
nect the Molex connector (orange and
gray wires) running from the touch-
screen controller cable to the main
power harness.

Remove the black poly tape from around
the edges of the old touchscreen (see
Figure 20). Remember how the tape
was placed in order to tape the new
touchscreen.

Use dental floss to carefully cut the
foam tape holding the touchscreen to
the picture tube until you are able to
completely remove the touchscreen.

Remove any remaining adhesive resi-
due with denatured alcohol, then wipe
the surface of the picture tube with the
supplied alcohol wipe.

17 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 18

FIGURE 17 - MEGATOUCH COMBO JUKEBOX - INSIDE REAR OF CABINET

BOLTS AND
WING NUTS
FASTENING
FRONT
BEZEL TO
CABINET
(BOTH
SIDES)

FIGURE 18 - MEGATOUCH COMBO JUKEBOX - INSIDE REAR OF CABINET

BOLTS AND

WING NUTS
FASTENING

FRONT

BEZEL TO

CABINET

(BOTH

SIDES)

DUAL FAN
ASSEBMLY

FIGURE 19 - MEGATOUCH COMBO JUKEBOX - INSIDE REAR OF CABINET

TOUCHSCREEN

CONTROLLER

ETHERNET
HUB

19 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

FIGURE 20 - MEGATOUCH COMBO JUKEBOX - MONITOR AND TOUCHSCREEN

BLACK

POLY
TAPE

Touchscreen Replacement

Clean the reverse side of the replace-
ment touchscreen with the supplied al-
cohol wipe.

If there is no tape already on the touch-
screen, cut pieces of the supplied 1/2”
foam tape long enough to cover each
edge of the screen without overlap-
ping. After the tape is in place on the
screen, peel off the backing.

10. Replace the new touchscreen over the

monitor (with the cable on the left if
you are facing the game), making sure
the screen is properly and evenly
aligned over the picture tube. Then
clean the front of the screen with the
supplied alcohol wipe.

11. Remembering the manner in which the

tape was placed around the touch-
screen you removed, place and cut a
length of the supplied black poly tape
evenly over an entire edge of the touch-
screen and repeat until all 4 edges are
covered.

12. Place and cut a longer length of black

poly tape around all 4 edges of the
screen.

13. Connect the new touchscreen control-

ler cable in the back of the controller
and secure the controller with the ex-
isting hardware. Also connect the
Molex connector (orange and gray
wires) to the main power harness.

14. Carefully replace the front bezel, lining

up the holes in the bezel with the screw
holes on the game. Then replace the 6
bolts and wing nuts (3 per side) fas-
tening the bezel to the game. Refer to
figures 17 and 18.

15. Plug in and turn on the game.

16. When the game is finished booting, cali-

brate the touchscreen. Then, ensure
that the screen is properly aligned, and
make any necessary adjustments with
the monitor control board.

17. Replace and lock the rear door.

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 20

MR. VIPS GAMES

Touchscreen Removal

Turn off and unplug the game.

Unlock and remove the upper rear door.

To remove the large prize assembly,
first remove the 2 nuts and bolts fas-
tening the cap and unplug the fluores-
cent light assembly, then remove the
remaining 8 nuts and bolts fastening
the prize assembly to the game. The
cap and prize assembly can be re-
moved together. See Figure 21.

To proceed with touchscreen removal,
first determine the type of hardware
securing the shroud to your game. See
Figures 22 and 23.

Games with screws securing front
of shroud:

•

To remove the front bezel from
the shroud, remove the 4 screws
on the underside of the bezel
(see Figure 22), then remove the
4 screws (2 per side) on either
side of the front bezel (see Fig-
ure 24). The bezel can then be
removed.

NUTS/BOLTS

SECURING

CAP TO

GAME

LARGE PRIZE

ASSEMBLY

SHROUD

NUTS/BOLTS

SECURING

BOTTOM OF

LARGE PRIZE

ASSEMBLY

TO GAME

NUTS/BOLTS
SECURING SIDE

OF LARGE
PRIZE
ASSEMBLY
(3 PER SIDE)

FIGURE 21 - SIDE/REAR VIEW OF GAME

21 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

Games with bolts securing front
of shroud:

•

Remove the cable clamp fastening
the small prize assembly light wir-
ing to the monitor frame. See Fig-
ure 25.

•

From inside the game, access and
remove the 4 screws (2 per side)
fastening the sides of the shroud
to the game. See Figure 26.

•

Remove the bolts and nuts (there
may be as many as 6) securing
the monitor to the game (see Fig-
ures 27-29 for possible locations).

Then carefully pull the monitor to-
wards you until you have enough
room to access the 4 nuts securing
the bolts holding the front of the
shroud to the game. Remove the nuts
and bolts, then carefully remove the
shroud and small prize assembly
from the game.

Remove the black poly tape (see Fig-
ure 30) from around the edges of the
old touchscreen, keeping the manner
in which the tape was placed around
the screen in mind.

Remove the two nuts and washers se-
curing the touchscreen controller to the
inside of the monitor (see Figure 31)
and remove the controller from the
mounting screws. Then disconnect the
cable from the back of the controller
and disconnect the Molex connector
(orange and gray wires) running from
the touchscreen controller cable to the
main power harness.

Use dental floss to carefully cut the
foam tape holding the touchscreen to
the picture tube until you are able to
completely remove the touchscreen.

Remove any remaining adhesive resi-
due with denatured alcohol, then wipe
the surface of the picture tube with the
supplied alcohol wipe.

FIGURE 23 - FRONT OF SHROUD FASTENED WITH BOLTS

FIGURE 22 - FRONT OF SHROUD FASTENED WITH SCREWS

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 22

FRONT

BEZEL

SHROUD

SCREWS
FASTENING
FRONT
BEZEL TO
SHROUD
(2 PER SIDE)

FIGURE 24 - SIDE/FRONT OF GAME

CABLE

CLAMP

NECK
BOARD

SMALL PRIZE
ASSEMBLY
LIGHT
WIRING
(2 WIRES)

FIGURE 25 - REAR OF MONITOR

MONITOR
BASE

SCREWS

FASTENING

SIDES OF

SHROUD

TO GAME

(2 PER SIDE)

SHROUD

FIGURE 26 - INSIDE OF SHROUD

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 24

Touchscreen Installation

Clean the reverse side of the replace-
ment touchscreen with the supplied al-
cohol wipe.

10. Peel the backing from the 8 pieces of

double-sided foam tape already ad-
hered to the reverse side of the
touchscreen.

11. Replace the new touchscreen over the

12. Connect the new touchscreen control-

ler cable in the back of the controller
and secure the controller on the mount-
ing screws in the game with the exist-
ing hardware (see Figure 31). Also
connect the Molex connector (orange
and gray wires) to the main power
harness.

13. Remembering the manner in which the

tape was placed around the touch-
screen you removed, place and cut a
length of the supplied black poly tape
evenly over an entire edge of the touch-
screen and repeat until all 4 edges are
covered.

FIGURE 31 - TOUCHSCREEN CONTROLLER

BLACK

POLY TAPE

THUMBNUTS
SECURING
TOUCHSCREEN
CONTROLLER

FIGURE 30 - MONITOR AND TOUCHSCREEN

25 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

14. Place and cut a longer length of black

poly tape around all 4 edges of the
screen.

15.

Games with screws securing front
of shroud:

•

Replace the bezel in the shroud
and secure it with the 8 screws.
See Figures 22 and 24.

Games with bolts securing front
of shroud:

•

Replace the shroud and small prize
assembly, then secure the front of
the shroud with the 4 nuts and bolts
removed earlier.

•

Slide the monitor back into position
and secure it with the hardware
removed earlier (see Figures 27-
29 for hardware locations).

•

Replace the 4 screws (2 per side)
fastening the sides of the shroud
to the game. See Figure 23.

•

Replace the cable clamp fastening
the small prize assembly light wir-
ing to the monitor frame. See Fig-
ure 25.

16. Replace the cap and large prize as-

sembly, then replace the 8 nuts and
bolts fastening the prize assembly to
the game. Then replace the 2 nuts and
bolts fastening the cap to the game and
plug in the fluorescent light. See Fig-
ure 21.

17. Replace and lock the upper rear door.

18. Plug in and turn on the game.

19. When the game is finished booting, cali-

brate the touchscreen. Then, ensure
that the screen is properly aligned, and
make any necessary adjustments with
the monitor control board.

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 26

ION EVO, EVO WALLETTE,
MEGATOUCH ENTERTAINER AND
ELITE EDGE GAMES

Touchscreen Removal

Turn off and unplug the game.

Unlock and open the CPU section and
place something under the front bezel
to brace it when the strain relief cord is
disconnected.

Remove the screw and washer fas-
tening the strain relief cord, then re-
move the remaining 5 screws fasten-
ing the LCD mounting bracket to the
game. The key socket ground wire
will also be removed in the process.
See Figure 32.

FIGURE 32 - CLOSEUP OF CPU SECTION

Remove the nut, wire and bolt from
the key socket assembly located on
LCD mounting bracket, then remove
the bracket. See Figure 32.

Carefully cut the tie wraps around the
VGA monitor cable, remove the
ground wire and disconnect the cable
from the monitor. See Figure 32.

Remove the OSD cable from the twist
clamp and disconnect it from the OSD
board and the monitor. Then remove
the OSD board from the Velcro at-
tached to the hinge and set it aside.
See Figure 32.

KEY SOCKET

ASSEMBLY

TOUCHSCREEN
CONTROLLER
CABLE ON
TOUCHSCREEN
CONTROLLER

OSD
BOARD

LCD MOUNTING

BRACKET

VGA MONITOR CABLE

OSD
CABLE

VGA MONITOR CABLE

GROUND WIRE

TOUCHSCREEN

CONTROLLER

CABLE GROUND

WIRE

TOUCHSCREEN
POWER CABLE

27 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

Disconnect the LCD power connector
(black and yellow wires). See Figure
33.

Carefully cut the tie wrap around the
touchscreen controller cable and dis-
connect the cable from the
touchscreen controller. Also remove
the ground wire. See Figure 32.

Disconnect the touchscreen power
cable from the touchscreen controller
(see Figure 32), then disconnect the
Molex connector identified by the or-
ange and gray wires.

10. Loosen the 3 screws on the monitor

side of the hinges in order to raise the
hinges and allow room to remove the
monitor. See Figure 33.

NOTE:

Elite Edge games may require

you to remove the joystick in order to
allow the necessary room for loosen-
ing of the hinge screws. To remove
the joystick, carefully place the game
on its side. Remove the 2 screws

CPU SIDE

OF HINGE

MONITOR SIDE

OF HINGE

LCD POWER CONNECTOR

FIGURE 33 - CLOSE-UP OF MONITOR HINGE

securing the protective bracket on the
bottom of the game and remove the
bracket. Disconnect the joystick con-
nector and remove the joystick. Re-
turn the game to its upright position.

11. Slide the monitor out of the bezel.

12. Note the orientation of the touchscreen

cable before removing the screen.
Then use dental floss to carefully cut
the foam tape holding the touchscreen
to the monitor until you are able to com-
pletely remove the screen.

13. Remove any remaining adhesive resi-

due with denatured alcohol, then clean
the monitor glass with the supplied al-
cohol wipe.

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 28

Touchscreen Installation

14. Clean the reverse side of the replace-

ment touchscreen with the supplied al-
cohol wipe.

15. Cut pieces of the supplied 1/2” double-

sided foam tape long enough to cover
each edge of the screen without over-
lapping. After the tape is in place on
the screen, peel off the backing.

16. Replace the new touchscreen over the

monitor in the same manner as the old
screen, making sure the screen is prop-
erly and evenly aligned over the moni-
tor glass. Then clean the front of the
screen with the supplied alcohol wipe.

17. Carefully slide the new monitor into

the bezel, making certain that the white
edge of the monitor and the monitor
wire connections are facing the bot-
tom of the bezel. Ensure that the moni-
tor is properly centered, then tighten
the hinge screws. See Figure 33.

NOTE

: If you removed the joystick on

your Elite Edge, carefully return the
game to its side and reconnect the joy-
stick to the connector in the game.
Place the protective bracket in its pre-
vious position, sliding it under the lazy
Susan and making sure the cutouts
are placed around the installed
screws. Make sure all wires are se-
cured inside the bracket, then reinstall
the 2 screws securing the bracket.
Return the game to its upright position.

18. Replace the LCD mounting bracket in

the game and fasten it with the 6
screws removed earlier. Also refas-
ten the strain relief cord and the key
socket ground wire. See Figure 32.

19. Replace the key socket assembly by

securing the bolt, green wire and nut
over the LCD mounting plate. See Fig-
ure 32.

Connect the touchscreen controller
cable to the touchscreen controller and
secure it with a tie wrap. Also restore
the touchscreen controller cable
ground wire. See Figure 32.

21. Connect the touchscreen power cable

to the touchscreen controller (see Fig-
ure 1) and reconnect the Molex con-
nector (orange and gray wires).

22. Connect the LCD power connector

(black and yellow wires). See Figure
33.

23. Reattach the OSD board to the Velcro

on the hinge, then connect the OSD
cable to both the OSD board and the
monitor. See Figure 32. Secure the
cable in the twist clamp.

24. Connect the VGA cable to the monitor

and secure it with tie wraps. Also
replace the ground wire. See Figure
32.

25. Plug in and turn on the game.

26. Once the game has booted up, press

27. Close and lock the CPU section.

29 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

ION AURORA GAMES

Touchscreen Removal

Turn off and unplug the game.

Unlock the rear door and open if it is
hinged, or remove if it is detachable.

Reach under the center of the top of
the cover to locate the rotary draw
latch (see Figure 34). Turn the wing
on the latch counterclockwise to dis-
engage.

Unscrew the screw located in the cen-
ter of the bottom of the cover (see
Figure 35). Slowly lift the cover and
disconnect the ground wire.

FIGURE 34 - ROTARY DRAW LATCH INSIDE TOP COVER

FIGURE 35 - SCREW IN CENTER OF BOTTOM COVER

Place something in front of the game to
brace the bezel once the strain relief
cord is undone, then remove the screw
at the center of the marquee bezel and
the 2 screws on the back of the bezel.
For 17” games, remove the security
screw inside the CPU section; for 19”
games, remove the nut and washer se-
curing the security bolt inside the CPU
section. See Figure 36.

Open the monitor assembly halfway
and remove the screw fastening the
strain relief cord. See Figure 37. Open
the assembly all the way and rest it on
a support.

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 30

SCREWS ON

BACK OF

BEZEL

(2 PLACES)

SECURITY

SCREW (17”)

OR SECURITY

BOLT, WASHER

AND NUT (19”)

FIGURE 36 - SCREWS ON FRONT AND BACK OF BEZEL

Disconnect the VGA connector from
the monitor. Remove the screw se-
curing the VGA and touchscreen con-
troller ground wires to the monitor
(17”) or the nut securing the VGA and
touchscreen controller ground wires
to the ground screw on the back of
the monitor (19”). Disconnect the 14-
pin OSD cable (white wires) and the
LCD power connector (yellow & black
wires) from the monitor. See Figure
38 for 17” games, Figure 39 for 19”
games.

Disconnect the touchscreen power
cable from the touchscreen control-
ler, then disconnect the Molex connec-
tor, identified by the orange and gray
wires. See Figure 38 for 17” games,
Figure 39 for 19” games.

Release harnesses from clamps; this
may include the inverter cable, the in-
verter power harness, the Molex har-

ness, the touchscreen controller
cable, the touchscreen controller cable
ground wire, the harness connecting
the Molex connector to the power
supply, and/or the touchscreen ribbon
cable. See Figure 38 for 17” games,
Figure 39 for 19” games.

10.

For 19” games:

Remove the inverter

from the Velcro securing it to the LCD
bracket and carefully place it out of
the way of the monitor assembly. See
Figure 39.

11. Carefully cut the tie wraps around the

touchscreen controller cable and dis-
connect the cable from the
touchscreen controller. Remove the 2
screws securing the touchscreen
controller to its mounting plate (17”) or
the LCD bracket (19”), then remove
the controller, as well as the fish pa-
per underneath. See Figure 40.

FIGURE 37 - HALFWAY-OPEN MONITOR ASSEMBLY

SCREW FASTENING

STRAIN RELIEF CORD

SCREW

THROUGH
MARQUEE

31 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

12. Remove the 4 screws securing either

the left and right LCD mounting brack-
ets to the bezel (17”) or the LCD
bracket to the bezel (19”), then care-
fully slide the monitor assembly out of
the bezel. See Figure 41 for 17” games,
Figure 42 for 19” games.

13.

For 17” games:

Remove the 4 screws

securing the LCD mounting brackets
to the monitor (2 per bracket). If re-
placing the monitor, remove the fish
paper/foam tape strip attached to the
top edge of the monitor. See Figure
41.

14. Note the orientation of the touchscreen

(i.e. the positioning of the ribbon cable
and which side is the front) before
removing it from the monitor. Then use
dental floss to carefully cut the foam
tape holding the screen to the monitor.
Once the touchscreen is completely
free from the monitor, remove any re-
sidual foam tape from the screen with
denatured alcohol and clean the glass
with the supplied alcohol wipe.

FIGURE 38 - REAR VIEW OF 17” MONITOR - CONNECTIONS

1. OSD cable
2. LCD power connector
3. Molex connector
4. Touchscreen controller
5. Inverter cable
6. Touchscreen controller cable
7. Inverter

8. Touchscreen power cable
9. Inverter power harness
10. Touchscreen controller cable ground wire
11. Ground screw
12. VGA cable ground wire
13. VGA monitor cable

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 32

SCREWS

SECURING

TOUCHSCREEN

CONTROLLER TO

MOUNTING PLATE

(17”) OR LCD

BRACKET (19”)

(2 PLACES)

FISH PAPER
UNDERNEATH
TOUCHSCREEN

CONTROLLER

TOUCHSCREEN
CONTROLLER CABLE
ON TOUCHSCREEN
CONTROLLER

FIGURE 40 - TOUCHSCREEN CONTROLLER

FIGURE 39 - REAR VIEW OF 19” MONITOR - CONNECTIONS

1. OSD cable
2. LCD power connector
3. Inverter power harness
4. Molex connector
5. Touchscreen ribbon cable
6. Inverter cable (white wires)
7. Inverter

8. Touchscreen controller
9. Touchscreen power cable
10. Touchscreen controller cable ground wire
11. Ground screw and nut
12. VGA monitor cable ground wire
13. VGA monitor cable

33 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

SCREWS

SECURING

LCD BRACKET

TO BEZEL (ALSO 2

ON RIGHT SIDE)

MOUNTING HOLES FOR

TOUCHSCREEN

CONTROLLER

(2 PLACES)

VELCRO FOR
INVERTER

FISH PAPER BETWEEN
MONITOR ASSEMBLY AND
LAMP BRACKET

FIGURE 42 - REAR VIEW OF 19” MONITOR - HARDWARE

FISH PAPER

LEFT LCD

MOUNTING

BRACKET

TOUCHSCREEN CONTROLLER

RIBBON CABLE

SCREWS
SECURING
BRACKET TO
BEZEL (ALSO 2

ON LEFT SIDE)

TOUCHSCREEN CONTROLLER

MOUNTING PLATE

RIGHT LCD
MOUNTING
BRACKET

FIGURE 41 - REAR VIEW OF 17” MONITOR - HARDWARE

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 34

Touchscreen Installation

15. Clean the glass on the LCD monitor

that you will be using with the sup-
plied alcohol wipe, then cut pieces of
the supplied 1/2” foam tape long
enough to cover the edges of the moni-
tor without overlapping. After the tape
is in place, peel off the backing.

16.

If replacing only the monitor:

Care-

fully place the touchscreen over the
new monitor in the same manner it was
attached to the old monitor, making sure
that the screen is properly and evenly
aligned over the monitor glass. Clean
the front of the touchscreen with the
supplied alcohol wipe once it is in
place. Reattach the fish/paper foam
tape strip to the top edge of the moni-
tor (17” games only; see Figure 41).

If replacing only the touchscreen:

Carefully place the new touchscreen
over the monitor in the same manner
as the old screen, making sure that
the screen is properly and evenly
aligned over the monitor glass. Clean
the front of the touchscreen with the
supplied alcohol wipe once in place.

If replacing both the monitor and the
touchscreen:

Carefully place the new

touchscreen over the new monitor in
the same manner that the old
touchscreen and monitor were
attached, making sure that the screen
is properly and evenly aligned over
the monitor glass. Clean the front of
the touchscreen with the supplied
alcohol wipe once it is in place.
Reattach the fish/paper foam tape strip
to the top edge of the monitor/
touchscreen assembly (17” games
only; see Figure 41).

17.

For 17” games:

Replace the left and

right mounting brackets on the monitor
and secure each with 2 screws.
Carefully slide the new monitor into
the bezel, making certain that the edge
of the monitor with the fish paper is
secured underneath the touchscreen
controller’s mounting plate. Ensure that
the monitor is properly centered, then
secure the mounting brackets to the
bezel with 4 screws. See Figure 41.

For 19” games:

Carefully slide the

new monitor assembly into the bezel,
making sure that the strip of fish paper
is secured between the edge of the
assembly with the Velcro and the lamp
mounting bracket. Ensure that the
monitor is properly centered, then
secure the LCD bracket to the bezel
with 4 screws. See Figure 42.

18.

For 17” games:

Line up the

touchscreen controller on the
rectangular piece of fish paper.
Connect the touchscreen controller
cable to the touchscreen controller and
secure with 2 tie wraps, making sure
that the wraps go around the fish paper
as well. Position this touchscreen
controller assembly on the mounting
plate and secure with 2 screws. See
Figure 40.

For 19” games:

Replace the inverter

on the Velcro. Place the rectangular
piece of fish paper on the mounting
holes on the LCD bracket. Carefully
connect the touchscreen controller
cable to the touchscreen controller and
secure with 2 tie wraps. Position the
touchscreen controller on top of the
fish paper and secure to the LCD
bracket with 2 screws. See Figure 40.

35 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

19. Secure the inverter’s cable and power

harness under clamp(s). See Figures
38 and 39.

20. Reconnect the LCD power connector

(black and yellow wires), and secure
the wires under a clamp.

21. Reconnect the touchscreen power

cable to the touchscreen controller and
reconnect the Molex connector (or-
ange and gray wires). Secure the
Molex wires and the touchscreen
ground wire under a clamp. See Fig-
ures 38 and 39.

22. Reconnect the 14-pin OSD connector

and the VGA cable to the monitor. For
17” games, replace the touchscreen
and VGA ground wires, and secure
with 1 screw. See Figure 38. For 19”
games, replace the touchscreen and
VGA ground wires on the ground
screw on the LCD bracket and secure
with one nut. See Figure 39.

23. Replace the strain relief cord and se-

cure in place with one screw. See Fig-
ure 37.

TAB

MATING HOLE

NOTE: ONLY LEFT SIDE SHOWN.

TAB AND MATING HOLE ARE

ALSO ON RIGHT SIDE.

FIGURE 43 - SIDE VIEW OF GAME

24. Close the monitor assembly completely,

and fasten with 2 screws in the back
of the bezel, 1 security screw (17”)
or security washer and nut (19”), and
1 screw in the front (through the mar-
quee). See Figure 36.

25. Reconnect the ground wire to the rear

cover and lower the cover into place,
carefully lining up the 2 tabs on the
cover with the 2 mating holes on the
sides of the game (see Figure 43).
Make sure that the plastic lip on the
bottom of the rear cover is behind the
metal base. Tighten the screw secur-
ing the bottom of the door. (Figure 35).
Turn the wing on the draw latch clock-
wise to engage it (see Figure 34).

26. Plug in and turn on the game.

27. Once the game has booted up, press

28. Close (or reattach) and lock the rear

door.

PM0331-05 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT 36

FIGURE 44 - REAR VIEW OF MONITOR / UNDERSIDE OF BEZEL

LCD POWER
CONNECTOR

THUMBNUTS
(6 PLACES)

OSD CABLE
CONNECTION

VGA MONITOR CABLE

GROUND
WIRES

TOUCHSCREEN
CONTROLLER CABLE

TOUCHSCREEN CONTROLLER

ION FUSION GAMES

Touchscreen Removal

Turn off and unplug the game.

Unlock and open the bezel.

Remove the 6 thumbnuts fastening the
bezel to the game. See Figure 44.

Loosen the bezel only enough to gain
access to the wire connections un-
derneath, then disconnect the button
controller wire connection at the foot
of the bezel.

Proceed to the top of the bezel and
remove the key socket wire and ground
wire. See Figure 45. Also remove the
wire connection to the coin mecha-
nism on the opposite side of the bezel.

Remove the bezel.

Remove the tie wraps securing the
wire harnesses to the back of the
monitor. Disconnect the VGA monitor
cable connection and ground wire.
See Figure 44.

Disconnect the LCD connector and
remove the OSD cable connection
from the monitor. See Figure 44.

Remove the tie wrap around the
touchscreen controller and disconnect
the touchscreen controller cable. Dis-
connect the Molex connector (orange
and gray wires), as well. See Figure
44.

10. Use dental floss to carefully cut the

foam tape holding the touchscreen to
the monitor until you are able to com-
pletely remove the screen. Once the
touchscreen is completely free from
the monitor, remove any residual foam
tape from the monitor with denatured
alcohol.

11. Clean the glass on the reverse side of

the new or existing touchscreen with
the supplied alcohol wipe, then cut
pieces of the supplied 1/2” foam tape
long enough to cover each edge of
the monitor without overlapping. Af-
ter the tape is in place on the monitor,
peel off the backing. Carefully place
the touchscreen over the monitor in
the same manner it was attached to
the old monitor, making sure the
screen is properly and evenly aligned
over the glass. Clean the front of the
touchscreen with the supplied alco-
hol wipe once it is in place.

12. Lift the bezel to access the reverse

side of the monitor. Connect the
touchscreen controller cable to the
touchscreen controller, then connect
the Molex connector (orange and gray
wires). See Figure 44.

13. Restore the OSD cable and the VGA

monitor cable to the back of the moni-
tor, and reconnect the VGA monitor
cable ground wire. See Figure 44.

KEY

SOCKET

GROUND

WIRE

FIGURE 45 - KEY SOCKET AND GROUND

37 MEGATOUCH FORCE & ION TOUCHSCREEN REPLACEMENT PM0331-05

Touchscreen Installation

14. Reconnect the LCD power connector

(black and yellow wires). See Figure
44.

15. Return the bezel in place on top of the

game, but do not secure it. Recon-
nect all wire connections attached to
the bezel, including the key socket
wire, ground wire (see Figure 45), coin
mechanism and button controller con-
nections.

16. Secure the bezel completely by fas-

tening the 6 existing thumbnuts. See
Figure 44.

17. Plug in and turn on the game.

18. Once the game has booted up, press

19. Close and lock the bezel, then cali-

brate the touchscreen.

NOTES:

__________________________________________________________________

_______________________________________________________________

________________________________________________________________

___________________________________________________________________

_______________________________________________________________

________________________________________________________________

__________________________________________________________________

_________________________________________________________________

______________________________________________________________

________________________________________________________________

___________________________________________________________________

__________________________________________________________________

_________________________________________________________________

_____________________________________________________________________