manuals/manuals_Support_Center_manuals_90003011_20Rev_20D_20Force_20TSM

Section 1 - Cabinet Information

General Information- All FORCE Products

Dimensions/Shipping Weights

General Information - FORCE Classic

Parts Illustrations

General Information - FORCE Elite

Parts Illustrations

General Information - FORCE Radion

Parts Illustrations

General Information - FORCE Upright

Parts Illustrations

General Information - The Vibe

Parts Illustrations

General Information - EVO

Parts Illustrations

General Information - EVO Wallette

Parts Illustrations

General Information - FORCE Upright Fusion

Parts Illustrations

General Information - Mr. VIPS

Parts Illustrations

General Information - Merit/TouchTunes Products

Parts Illustrations

FORCE Parts List

Section 2 - Hard Drive Information

Hard Drive Numbers

Program Numbers
Part Numbers
Security Key Numbers

Section 3 - Troubleshooting Information

Touchscreens

Troubleshooting
Advanced Touchscreen Calibration

Motherboard Handling Precautions
Motherboard Diagrams
Removal/Installation of Major Assemblies
DIP Switch Settings in FORCE Games
Troubleshooting Guide (

FORCE 2002 and earlier)

Troubleshooting Guide (

FORCE 2003 and later)

TouchTunes® Troubleshooting Guide
CMOS Setup
Mars 2000 Bill Acceptor

DIP Switch Settings

Section 4 - Power Supply

Power Supply Used in FORCE Games

Enhance SFX-1211J

Enhance ENP-0812A

Section 5 - Motherboard

Circuit Board Cross Reference Chart
Motherboard Diagrams
I/O Board Diagrams

Section 6 -

Monitors

Monitors Used in FORCE Games
Monitor Adjustments

Degaussing
Monitor Adjustment Procedures

Section 7 - Technical Service Bulletins

FLDBLL 24

- Problem with Megatouch FORCE

2002 software release

TN 52

- Installing the Power-On Harness on an

ECS Motherboard

FLDBLL 25 -

Software bug affecting high scores

TN 55

- Replacing the I/O Board on a Megatouch

FORCE Game

FLDBLL 26

- Fix for Software bug affecting high

scores

FLDBLL 27

- Problem with MARS series 2000 Bill

Acceptor

TN 56 Rev. A -

Replacing the Monitor Chassis

Board in FORCE Radion Games

TN57

- New Jersey games and coin mech and bill

acceptor operation

TN60

- Radion monitor chassis board replacement

FLDBLL 29 -

Canadian FORCE 2003 and Ruby

security keys

FLDBLL 30

- FORCE Radion Games with

Incorrect Circuit Breakers

TN58

- Software Updates While Running

Championship Tournaments

TN67

- Replacing the Control Board in Megatouch

Combo Jukebox and MegaTunes Units

TN72

- I/O Board Replacement in FORCE EVO

and Fusion Games

TN76

- FORCE 2004 Point 5/Sapphire 2 Update

Disc

TN53 Rev M

- How to Read a Game Serial

Number

TN65 Rev. D

- DIP switch settings in FORCE and

MAXX games

FLDBLL 34 -

FORCE 2005 and Jade

Championship Edition Software Bug

FLDBLL 33B

- FORCE 2005 and Jade Software

Bug

FLDBLL 35B

- TouchTunes® Interconnectivity

License Expiration

Megatouch FORCE Technical Service Manual Contents

Cabinet Information Section

General Information

Cabinet Information - General Information - All Cabinet Styles

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Classic

Dimensions: D=20”; W=21”; H=16”
Shipping dimensions: D=23”; W=26; H=22”
Shipping weight: 100 lbs.

Megatouch FORCE Elite

Dimensions: D=17.5”; W=16”; H=15.5”
Shipping dimensions: D=18.5”; W=21”; H=20”
Shipping weight: 75 lbs.

Megatouch FORCE Radion

Dimensions: D=18”; W=20”; H=15.25”
Shipping dimensions: D=23”; W=26”; H=22”
Shipping weight: 90 lbs.

Megatouch FORCE Upright

Dimensions: D=29”; W=23”; H=62”
Shipping dimensions: D=30.5”; W=26”; H=65.5”
Shipping weight: 270 lbs.

The Vibe

Terminal: D=7”; W=14”; H=16”
Processor: D=15”; W=11.5”; H=4.5”
Shipping weight: 50 lbs.

Megatouch FORCE EVO

Dimensions: D=15”; W=16.5”; H=18.5”
Shipping weight: 75 lbs.

Megatouch FORCE EVO Wallette

Dimensions: D=9”; W=16.5”; H=19”
Shipping weight: 65 lbs.

Megatouch FORCE Upright Fusion

Dimensions: D=21”; W=20”; H=61”
Shipping weight: 200 lbs.

Megatouch FORCE Fun Zone

Dimensions: D=21”; W=25”; H=67

Shipping weight: 175 lbs.

Megatouch FORCE Fun Zone Jr.

Dimensions: D=22”; W=25”; H=43.75”

Megatouch Mr. VIPS

Dimensions: D=30”; W=28”; H=79”

Megatouch Combo Jukebox

Dimensions: D=26”; W=25”; H=71.25”
Shipping Dimensions: D=28.5”; W=35.5”;
H=78.5”
Shipping weight: 425 lbs.

MegaTunes

Dimensions: D=15.5”; W=20.25”; H=4.75”

Remote Sound System

Cabinet Dimensions: D=23”; W=23”; H=26.5”

FORCE CLASSIC COUNTERTOP

Cabinet Information - General Information - FORCE Classic

Megatouch FORCE Technical Reference Manual

SA0108-04
(main harness)

MW0010-02-0J

(monitor frame)

SA0313-01

(speaker assembly)

HW8993-02

(lazy susan)

HW8018-02

(anti-skid pad)

HW8741

(lock)

CN4452-01
(phone coupler)

CN4451-01
(Ethernet coupler)

EC3040
(circuit breaker)

SA0225-06

(AC harness)

MW0015-01
(lock bracket)

MW0038-01
(cord clip)

MW0009-02-0D
(chassis)

EC9154-03
(counter)

SA0226-04

(DC harness)

SA0103-07

(monitor & touchscreen)

EC9377-08

(monitor)

SA9824-01

(touchscreen)

HW8953-03

SA5129-01

(bezel & gasket)

SA5117-04-0A

(fan assembly

EC9402-03

(fan)

HW8989

(fan guard)

MW0014-02-0B
(left latch plate)
MW0014-01-0B
(right latch plate)

EC2198-01
(centronics ribbon cable)

SW4084

(ON/OFF switch)

EC7531-03

SA0106-12

(power supply)

SA10055-01
(I/O board)

EC9840-08
(touchscreen controller)

SA10057-05
(motherboard)

WD0001-05

(right side panel)

SA0117-01
(fan power harness)

WD0001-06

(left side panel)

MW0016-01-0C
(door)

HW8734-01
(lock)
MW0024-01
(cam)

GL3100-47

(FORCE 2005 decal)

PA3024-01
(FORCE 2006
hard drive)

FORCE ELITE COUNTERTOP

Cabinet Information - General Information - Megatouch FORCE Elite

Megatouch FORCE Technical Reference Manual

SA0267-03

EC7531-03

(power supply)

SA4084

(speaker)

SA5117-08

SA0279-01

(fan)

SA10057-05

(motherboard)

MW0425-01
(chassis)

MW0327-01
(coin return chute)

EC2198-01

(centronics ribbon cable)

HW8993-02

(lazy susan)

HW8018-02

(anti-skid pad)

SA0241-05

MP0001-09

(left side cover)

SA0242-06
(power entry assembly)

CN4451-01
(Ethernet coupler)

SA0298-02

EC9796-04
(bill acceptor)

SA10055-01

(I/O board)

HW8733-05

(lock)

SA10058-01

(audio amp board)

SA0240-05

(coin drawer)

EC3040

(circuit breaker)

EC2008-01

(line cord)

HW8159-01

(domestic coin mech)

HW8317-XX

(electronic coin mech--

international only)

MW0324-02

(coin entry plate)

SW4024
(ON/OFF switch)

EC9840-08
(touchscreen controller)

MW0447-01
(power supply bracket)

CN4452-02
(phone coupler)

SA0331-01
(hard drive assembly)

MW0494-01
(hard drive bracket)
PA3024-01
(FORCE 2006 hard drive)

FORCE RADION COUNTERTOP

Cabinet Information - General Information - Megatouch FORCE Radion

Megatouch FORCE Technical Reference Manual

SA0338-01* (coin box & bill acceptor--

for games produced before October 7, 2002)

SA0338-07 (oversized coin box & bill acceptor--

for games produced after October 7, 2002)

SA0338-11 (oversized coin box w/o bill acceptor--

for games produced after November 27, 2002)

EC9796-01 (bill acceptor only)
MW0475-01* (metalwork only)
MW0566-01 (metalwork only--large)

MW0471-01

(coin return chute)

SA0329-02

(monitor & touchscreen)

EC9387-01

(monitor)

EC9850-03

(touchscreen)

MW0470-01

(coin chute)

MW0020-01

(coin return lever)

MP0019-01

(coin entry plate)

EC9154
(counter)

MP0017-01
(rear door)

HW8159-01
(coin mech)

*If desired, an oversized coinbox upgrade kit can
be ordered:

KUV-112-000-01 includes coinbox only--
hardware (lock, etc.) would be reused.
KUV-112-001-01 includes bill acceptor, coinbox,

and hardware.

EC9387-01
(monitor assembly)

MW0542-01
(hard drive bracket)

EC2198-05
(centronics ribbon cable)

SA0326-01

MP0015-01

(rear door & bezel)

SA0327-01

MP0014-01

(front bezel)

SA0308-01

EC7531-03
(power supply)

EC0056-03
(DIMM)

PA3024-01
(FORCE 2006
hard drive)

THE VIBE

Cabinet Information - General Information - The Vibe

Megatouch FORCE Technical Reference Manual

SW4025-01
(on/off switch)

SA0400-01
(dual fan assembly)

CN4451-01
(Ethernet coupler)

HW8721
(lock)
MW0584-01
(cam*)

*not shown

EC3040

(circuit breaker)

MW0649-01

(access panel)

HW0057-02

(fan guard)

HW3151

(thumbnut)

SA0266-02

(IEC connector)

SA0388-01

(9-pin connector

from terminal)

EC3040

(circuit breaker)

CN4452-01
(phone coupler)

SA0402-01
(processor
cover assy.)
MW0575-02
(processor lid)

(motherboard assembly)

(processor base)

MW0575-03

(counter assembly)

SA0309-03

(FORCE 2006 hard drive)

PA3024-01

SA10055-01

EC0056-03

(CPU fan*)

(64MB memory*)
EC9401-07

SA10057-05

(I/O board)

(power supply)

EC7531-03

THE VIBE W/ COIN

Cabinet Information - General Information - The Vibe w/ Coin

Megatouch FORCE Technical Reference Manual

SA0400-01
(dual fan assembly)

(circuit breaker)

SW4025-01
(on/off switch)

HW8721
(lock)
MW0584-01
(cam*)

*not shown

MW0649-01

(access panel)

SA0388-01

(15-pin connector

from terminal)

HW0057-02
(fan guard)

EC3040

(circuit breaker)

HW3151

(thumbnut)

MW0680-01

(ribbon cable

adapter plate)

SA0456-01

(9-pin connector

from terminal)

SA0402-01
(processor
cover assy.)

MW0575-02
(processor lid)

CN4452-01

(phone

connector)

EC2198 01
(centronics

upgrade connector)

CN4451-01

(Ethernet

connector)

EC7531-03
(power supply)

SA0309-03

(counter assembly)

PA3024-01

(FORCE 2006 hard drive)

SA10055-01
(I/O board)

SA10057-05
(motherboard assembly)

EC0056-03
(64MB memory*)
EC9401-07
(CPU fan*)

MW0575-03
(processor base)

Cabinet Information - General Information - Megatouch FORCE EVO

Megatouch FORCE Technical Reference Manual

PARTS FOUND IN ALL EVO MODELS

DETAIL VIEW OF
CONTROL BOARD

EC0102-01

(setup)

EC0102-01

(calibrate)

MW0747-01

(controller bracket)

EC9840-08

(touchscreen controller)

SA10066-01

(OSD board)

PA3024-01

(hard drive)

HW8721

(lock)

MW0783-01

(lock slide)

SA10057-07 (motherboard)
SA10065-01 (I/O board)

EC0094-01 (I/O cable)
PA0060-XX (modem)
EC0098-03 (modem cable)
EC9401-09 (CPU fan)

MW0781-01
(hinge--2 places)

MW0740-01
(LCD mounting bracket)

EC0101-01
(speaker assembly)

EC7536-01
(power supply)

SB0409-01
(domestic front and rear
plastic enclosure)
SB0409-02
(international front and rear
plastic enclosure)

SA0470-01
(fan assembly)

MW0753-02

(lock spacer)

EC2198-01

(IDE cable)

GL0041-01
(base decal)

GL0038-01
(clear marquee)
PM8950-16
(FORCE 2006 sign)

SA0477-01
(LCD & touchscreen)
SA0469-01
(LCD w/ brackets & cabling)
EC9850-04
(touchscreen only)

Cabinet Information - General Information - Megatouch FORCE EVO

Megatouch FORCE Technical Reference Manual

EVO WITH BILL AND COIN

EVO WITH COIN ONLY

MP0048-01

(coin mech enclosure)

MW0735-01
(coin lever)

MW0733-01
(coin entry face bracket)

SB0377-01
(domestic mechanical
coin mech)

HW8317-XX
(international/Canadian

electronic coin mech)

HW8733-07

(lock)

MW0726-01

(cam)

MP0047-01
(coin return chute)

EC0092-02

(power entry & ON/OFF switch)

*EC2018-01

(power cord--USA)

*not shown

EC0100-01
(counter assembly)

MW0743-01

(small coin box)

EC9796-01

(bill acceptor)

SA10067-01
(LED board)

GL0025-03
(Merit logo overlay)

*HW1310-03

(U-bolt)

*not shown

EC0099-01

(fan)

MP0045-01
(bill acceptor nose

--front view)

MP0049-01
(coin entry faceplate)

MW0812-01
(bill acceptor front plate)

HW8993-02

(lazy susan)

HW8018-02

(anti-skid pad)

MP0048-01

(coin mech enclosure)

HW8733-07

(lock)

MW0726-01

(cam)

MW0731-01

(large coin box)

EC0099-01

(fan)

EC0092-02

(power entry & ON/OFF switch)

*EC2018-01

(power cord--USA)

*not shown

EC0100-01
(counter assembly)

SB0377-01
(domestic mechanical coin mech)
HW8317-XX
(international/Canadian electronic coin mech)
HW8333-XX
(electronic coin mech--wet deck)

MW0733-01
(coin entry face bracket)

MW0735-01
(coin lever)

MW0731-01
(large coinbox)

MW0726-01
(lock cam)

MP0047-01
(coin return chute)

*HW1310-03

(U-bolt)

*not shown

MW0812-02
(coin mech front plate)

MP0049-01
(coin entry faceplate)

HW8993-02

(lazy susan)

HW8018-02

(anti-skid pad)

Megatouch FORCE EVO Wallette

Dimensions: D - 9”; W - 16.5”; H - 19”

Motherboard Information

ECS

Touchscreen Type

Microtouch

Cabinet Information - General Information - Megatouch FORCE EVO Wallette

Megatouch FORCE Technical Reference Manual

DETAIL VIEW OF
CONTROL BOARD

EC0102-01

(setup)

EC0102-01

(calibrate)

MW0747-01

(controller bracket)

EC9840-08

(touchscreen controller)

SA10066-01

(OSD board)

PA3024-01

(hard drive)

HW8721

(lock)

MW0783-01

(lock slide)

SA10057-07 (motherboard)
SA10065-01 (I/O board)
EC0094-01 (I/O cable)
PA0060-XX (modem)
EC0098-03 (modem cable)
EC9401-09 (CPU fan)

MW0781-01
(hinge--2 places)

MW0740-01
(LCD mounting bracket)

EC0101-01
(speaker assembly)

EC7536-01
(power supply)

SB0409-01
(domestic front and rear
plastic enclosure)
SB0409-02
(international front and rear
plastic enclosure)

SA0470-01
(fan assembly)

MW0753-02

(lock spacer)

EC2198-01

(IDE cable)

Cabinet Information - General Information - Megatouch FORCE EVO Wallette

Megatouch FORCE Technical Reference Manual

EVO WALLETTE

MP0076-01

(upper cover)

HW8159-01

(coin mech)

MW0919-01

(coin mech bracket)

SW5021-01

(coin switch)

HW8727-03 (lock)

HW8757 (cam)

MW0914-01

(coin box)

MW0937-01

(lock slide riser)

EC9793-04

(bill acceptor)

MW0911-01 (back of

B/A bracket)

HW4206 (screws)

SA0514-01 (B/A harness)

HW4343

(screws securing B/A)

MP0075-01

(lower cover)

MW00908-01
(hinge riser)

SA0515-01
(main harness)
MW0913-01
(coin chute)

EC9304-05
(line filter)
SA0511-01 (AC
jumper harness)
SW4025
(on/off switch)

CN4452-01
(phone coupler)

EC2019-01
(power cord)

MW0905-01
(back plate)

HW2031-01
grommet

CN4451-01
(ethernet coupler)

MW0929-01
(lock catch)
HW4429
(2 screws)

MW0915-01
(back plate hinge)

Cabinet Information - General Information - Megatouch FORCE Elite Edge

Megatouch FORCE Technical Reference Manual

EC9796-06

(bill acceptor)

EC9702-XX

(Smiley bill acceptor)

CN4451-01

(Ethernet coupler)

CN4452-01

(phone coupler)

SW4025-02

(power switch)

EC2198-01 (centronics

upgrade connector)

EC0100-01 (meter)

MW0961-01 (bracket)

MW0721-01
(B/A-only cap)

HW8993-02 (lazy susan)
HW8018-02 (skid pad)

*not shown
EC2008-XX
(international power cord)
EC2001
(domestic power cord)

MW0969-01
(hinge bracket -
bill acceptor only)

HW1310-01 (u-bolt)

HW3300 (hexnut

HW3301 (kepnut)

GL3100-54
FORCE 2006
decal

HW0903-01(safety cover)

DETAIL VIEW OF
CONTROL BOARD

EC0102-01

(setup)

EC0102-01

(calibrate)

MW0747-01

(controller bracket)

EC9840-08

(touchscreen controller)

SA10066-01

(OSD board)

PA3024-01

(hard drive)

HW8721

(lock)

MW0783-01

(lock slide)

SA10057-07 (motherboard)
SA10065-01 (I/O board)
EC0094-01 (I/O cable)
PA0060-XX (modem)
EC0098-03 (modem cable)
EC9401-09 (CPU fan)

MW0781-01
(hinge--2 places)

MW0740-01
(LCD mounting bracket)

EC0101-01

EC7536-01
(power supply)

SB0409-01
(domestic front and rear
plastic enclosure)
SB0409-02
(international front and rear
plastic enclosure)

SA0470-01
(fan assembly)

MW0753-02

(lock spacer)

EC2187-01

(IDE cable)

Cabinet Information - General Information - Megatouch FORCE Elite Edge

Megatouch FORCE Technical Reference Manual

SA0477-01
(LCD & touchscreen)
SA0469-01
(LCD w/ brackets & cabling)
EC9850-04
(touchscreen only)

MW0733-01
(coin entry face bracket)

SB0377-01
(domestic mechanical coin mech)

HW8317-XX
(international/Canadian electronic coin mech)
HW8333-XX
(electronic coin mech--wet deck)

MP0049-01
(coin entry faceplate)

MP0086-01
(coin mech enclosure)

MW0735-01
(coin lever)

SA0470-03

(fan)

MW0939-01

(coin mech bracket)

HW4509-01

(screw)

*not shown
GL0041-02 (Elite Edge base decal)

MP0085-01 (front plate)
LB0004-01 (blue light)
MW0945-01 (domestic bill acceptor bracket)
MW0945-02 (Smiley bill acceptor bracket)
MW0945-03 (bill acceptor block out plate for coin only games)

GL0038-01
(clear marquee)
PM8950-16
(FORCE 2006 sign)

MW0942-02
(large coin box - coin
only games)

MW0942-03
(small coin box - coin
and bill games)
HW8314-01
(spring)
MW0981-01
(coin box support)

MW0967-01
(hinge bracket)

MP0086-01
(coin entry pod)

SW4025-02
(power entry
module)

MW0970-01
(enclosure)

MW0940-01
(coin chute)
MP0082-01
(coin cup)
HW8207
(screw)

MW0930-01
(base)

*not shown
MW0944-01 (rear door)
HW8733-03 (lock)
MW0510-01 (lock cam)

MEGATOUCH FORCE FUSION WITHOUT ELECTRONICS BOX

Cabinet Information - General Information - Megatouch FORCE Upright Fusion

Megatouch FORCE Technical Reference Manual

SA0177-05
(lamp assembly)

LB1030-01
(bulb)

EC9796-06
(bill acceptor)
MW0709-01
(bill acceptor mounting plate
MW0710-01
(bill acceptor shroud)

HW8731
(currency door lock)

MW0095-03
(stay arm)
MW0701
(stay arm upper bracket)
MW0098-01
(stay arm hat bracket)

GL0036-01*
(left panel decal)
GL0036-02*
(right panel decal)
*not shown

WD0047-01

(cabinet)

GL0035-01*

(front decal)

*not shown

SA10065-01

(I/O board)

EC2001*

(USA power cord)

*not shown

EC7531-03

(power supply)

HW8721

(lock)

MW0792-01

bezel lock mech)

EC9840-08

(touchscreen controller)

EC2198-01

(centronics ribbon cable)

PA3024-01

(hard drive)

SA10066-01

(OSD board)

MW0758-01

(bill acceptor cover)

MW0755-01*

(bill acceptor cover plate)

MW0756-01*

(bill acceptor cover plate backing

*not shown

MW0708-01
(currency door)
MW0700-01*
(coin box)
HW8401-02*
(pull handle)

*not shown

SA10057-01
(motherboard)
EC0056-03
(DIMM)
EC9401-09
(CPU fan)

HW8159-XX
(mechanical coin mech)
SA0473-01
(mechanical coin mech harness)
HW8317-XX
(electronic coin mech)
EC0104-02
(mechanical coin mech harness)

Cabinet Information - General Information - Megatouch FORCE Fun Zone

Megatouch FORCE Technical Reference Manual

HW8425-05

(gas strut)

HW8442-01

(bracket--top and bottom)

HW8423-01

(safety clip--top and bottom)

HW4487

(screws--2 top, 2 bottom)

MW0965-01

(red ticket dispenser door)

MW0965-02

(red printer door)

MW0965-04

(black ticket dispenser door)

MW0965-04

(black printer door)

MW0889-01
(cash door)

EC9796-06
(bill acceptor)
MW0755-02
(bill acceptor

cover plate)
MW0756-01
(backing plate)
GL0040-01
(B/A cover decal)

EC9840-08
(touchscreen controller)

MW0923-01

(red lower speaker panel)

MW0923-02

(red upper speaker panel)

MW0923-03

(black lower speaker panel)

MW0923-04

(black upper speaker panel)

HW8716
(speaker panel lock)
MW0895-01
(cam)
MW0897-03
(3-point lock bracket)
MW0899-01
(3-point lock arm)
HW8440-01
(spring)
HW8043
(cover)

SA4084

(speaker assembly)

SA10066-01
(OSD board)

GL0039-01

(Merit logo nameplate)

MW0902-01
(black foot cover)
MW0902-02
(blue foot cover)

WD0057-01

(red cabinet)

WD0057-02

(black cabinet)

HW1110

(screws)

HW5250
(washer)

HW8042-01

(power entry cover)

GL0046-02

(ticket decal)

GL0046-03

(coupon decal)

HW8727-02
(lock)
MW0927-01
(cam)

HW0118-01

(lamp cover with lights)

LB0002-01

(light bulb, left and right side)

MW0922-01

(red units - left lamp cover)

MW0922-02

(red units - right lamp cover)

MW0922-03

(black units - left lamp cover)

MW0922-04

(black units - right lamp cover)

HW8227-04
(cash box - located inside)
HW8727-02
(cash door lock)
MW0896-01
(lock cam)

Cabinet Information - General Information - Megatouch FORCE Fun Zone

Megatouch FORCE Technical Reference Manual

WD0057-01

(red cabinet)

WD0057-02

(black cabinet)

EC9304-05
(line filter w/ switch)

EC3040
(circuit breaker)

HW8716
(rear door lock)
MW0896-01
(cam)

MW0895-01
(bezel hinge)

MP0054-02

domestic black monitor bezel)

MP0054-03

(domestic blue monitor bezel)

MP0054-04

(Smiley black monitor bezel)

MP0054-05

(Smiley blue monitor bezel)

GL0037-01
(clear marquee holder--front)
GL0037-02
(clear marquee holder--back)
GL0034-04
(FORCE 2005 marquee)
SA0177-06
(domestic lamp assembly)
SA0177-07
(international lamp assembly)
LB1030-01
(light bulb)

SA0469-09
(LCD & touchscreen)
SA0469-04
(LCD and brackets)

EC9851-03
(touchscreen)
EC0096-01 (VGA cable)

SA0506-01 (LCD power cable)

CN4452-01
(phone coupler)
CN4451-01
(Ethernet coupler)

HW8403-01

(rear handle)

HW8989
(outside fan guard)

SA0307-02
(fan)

HW0117-01
(inside fan guard)

LB0003-02
(lamp)

*not shown
SB0408-01
(anti-tip kit)

MW0921-01 (red metal marquee)
MW0921-02 (black metal marquee)
HW4487 (screws for marquee)
KSV-112-000-06 (black marquee kit)

GL0047-01
(decal)

HW8249

(mechanical coin rejector)

HW8319-XX

(int'l coin rejector)

HW8500-XX

(int'l wet deck coin rejector)

Cabinet Information - General Information - Megatouch FORCE Fun Zone Jr.

Megatouch FORCE Technical Reference Manual

FORCE FUN ZONE JR.

CALIBRATE

SETUP

DETAIL VIEW

OF I/O BOARD

SECURITY KEY

MW0542-01
(hard drive bracket)

PA3020-02
(Fun Zone
hard drive)

SA0308-02

EC7531-03
(power supply)

EC2198-05
(centronics ribbon cable)

EC0056-01
(DIMM)

SA0326-02

MP0015-02

(red rear door

& bezel)

SA0327-03
MP00014-02
(red front bezel)

MP0016-02
(blue base)

*not shown
SA0318-01 (main power harness)
SA0320-01 (dual fan assembly
HW055-12 (fan guard)
HW8059-01 (front and rear bezel gasket)

MW0471-01

(coin return chute)

MW0470-01

(coin chute)

MW0491-01

(coin return lever)

SA0341-02

(coin entry assembly)

MP0019-03

(coin entry plate)

SA0309-01
(counter assembly)
SA0310-02
(counter harness)

SA00326-02
(bezel and door assembly)

HW8721
(lock)
MW0498-01
(cam)

HW8159-01
(dom coin mech)

SA0316-02
(coin harness)

SA0338-11 (oversized coin box w/o bill acceptor)
SA10042-01 (optical coin sensor)

HW8733-05 (lock)
MW0510-01 (cam)
MW0566-01 (metalwork only--large)

Cabinet Information - General Information - Megatouch FORCE Fun Zone Jr.

Megatouch FORCE Technical Reference Manual

FORCE FUN ZONE JR.

EC0051-01
(USB cable)

EC9840-08
(touchscreen

controller)

MP0034-01

(coin guard)

MP0021-08

(combo plate)

MW0521-01

(bill acceptor

alignment

bracket)

MP0015-02
(red rear
bezel)

MW0483-01
(rear door
hinge)

SA0329-02

(monitor & touchscreen)

EC9387-01

(monitor)

EC9850-03

(touchscreen)

SA0327-03

(blue front bezel)

MP0014-01

(red front bezel)

MW0965-01
(ticket door)

GL0045-02

(arrow up decal)

MW0959-01
(metal marquee)
GC0051-01
(decal)

GL0049-01
(merit logo decal)

MW0925-01

(ticket hopper)

EC9699-01

(ticket dispenser)

SA0518-01
(ticket harness)

PM9210-01
(tickets)

HW8159-01
(coin mech)

*not shown
SB0417-01 (anti-tip kit)
EC2015-05 (int’l power cord)
EC2018-01 (dom. power cord)

Mr. VIPS

Dimensions: D - 30”; W - 28”; H - 79”

Weight: 290 lbs.

Motherboard Information

ECS

Touchscreen Type

Microtouch

Cabinet Information - General Information - Mr. VIPS

Megatouch FORCE Technical Reference Manual

EC9387-01
(monitor)
EC9850-03
(touchscreen)

HW8722-01
(display case locks)

UPPER
COIN
DOOR
LOCK

PRIZE
DOOR

LOWER
COIN
DOOR
LOCK

DETAIL VIEW

INSIDE THE UPPER

COIN DOOR

BILL

ACCEPTOR

COIN

MECH

METER

CALIBRATION
(YELLOW)

SETUP
(RED)

MEDIUM PRIZE FILL

(INSIDE DISPLAY LID)

LOCKING
CASTOR

WHEELS

EC0127-01*

(blue light assembly

on each side of

prize assembly)

*not shown

EC0128-01*
(rope light

&controller)
*not shown

CLEAR
PLASTIC
DISPLAY
LID

Cabinet Information - General Information - Mr. VIPS

Megatouch FORCE Technical Reference Manual

MR. VIPS

GL3103-01 (left decal)*
GL3103-02 (right decal)*
GL3103-03 (Mr. VIPS logo decal)*
GL3104-01 (Play'n Win decal)*
GL3105-01 (Instant Redemption decal)*
GL3106-01 (Win a Prize decal)*
GL3107-03 (Center Arrow Prize decal)*
GL3108-01 (Prize Matrix decal)*
*not shown

EC2201-01*
(power outlet strip)
EC7537-02*
(120V to 12V wall

AC/DC converter)
*not shown

EC0131-01*

(fluorescent

light assembly

inside display case)

*not shown

SA10055-01

(I/O board)

EXTRA

SMALL

LARGE

DETAIL VIEW INSIDE

THE UPPER REAR DOOR -

PRIZE FILL LOCATIONS

SA10058-01

(audio amp board)

SA10057-05

(motherboard)

EC7531-03

(power supply)

DETAIL VIEW OF CPU SECTION

INSIDE THE LOWER REAR DOOR

ON THE LEFT WALL

HW8722-02
(lower rear

door locks)

HW8722-02
(upper rear

door locks)

PA0049-04

(hard drive)

Cabinet Information - General Information - Megatouch Combo Jukebox

Megatouch FORCE Technical Reference Manual

MEGATOUCH COMBO JUKEBOX

SA4084
(game speaker assembly--
both sides)
MW0615-01
(speaker bracket)

EC9790-01
(bill acceptor--

down stacker)
SA0377-02*
(bill acceptor/coin mech harness)
*not shown

HW8249
(coin mech)

MW0629-01

(card reader blanking plate)

SA0177-05*

(fluorescent lamp assembly)

LB1030-01

(6W bulb)

*behind rainbow side panel

SA0177-04-0A*
(fluorescent lamp assembly)
LB1030-01
(6W bulb)
*behind rainbow side panel

GL2435-01

(rainbow side panel)

SA3276-01

(upper bezel assembly--includes

GL2435-01 rainbow side panel)

MP0035-01

(upper bezel)

EC0085-01*
(primary light show--
includes secondary light show

*behind plastic marquee

SA0177-04-0A
(fluorescent lamp assembly)
LB1030-01
(6W bulb)

GL2436-01

(clear oval marquee--

one behind, one in front)

GL0030-05

(FORCE 2006 marquee)

EC0087-01
(remote control)
EC9100*
(AA battery)

*not shown

EC9383-01 (monitor)
EC9851-12 (touchscreen)

WD0038-01 (wooden shelf)

Cabinet Information - General Information - Megatouch Combo Jukebox

Megatouch FORCE Technical Reference Manual

MEGATOUCH COMBO JUKEBOX

SA0309-02
(counter assembly)

SA0403-01
(volume controls)

SA0307-01
(fan assembly)
MW0489-01
(fan bracket)
HW3150
(6-32 kepnut)

HW8716*
(rear door lock)

*not shown

SA0307-01

(fan assembly)

MW0489-01

(fan bracket)

HW3150

(6-32 kepnut)

SW4024

(rocker switch)

SA0443-01*

(AC fan assembly)

*not shown

SA0064-04*

(power assembly)

EC3040-02*

(circuit breaker)

SW4024*

(on/off switch)

CN0002-01*

(power inlet connector)

*not shown

SA0408-02*

(Ethernet hub

power cable)

*not shown

SA0431-01

(communication

inerface module--

includes connectors

and switches)

HW8840-02*

(spiral cable wrap)

*not shown

CN4452-01

(phone connector)

EC0074-03*

(50' phone cable)

*not shown

CN4451-01

(Ethernet connector)

EC9840-10*
(touchscreen controller)

*not shown

SA0307-01*
(fan assembly)
MW0489-01*
(fan bracket)
HW3150*
(6-32kepnut)
*not shown

EC0063-01*
(Ethernet hub)

*not shown

GL2442-01
(top clear
light panel)

HW8716
(rear door lock)

Megatouch FORCE Parts List

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Item

Description

CN0029-01

RIGHT ANGLE MALE XLR CONNECTOR

CN0031-01

RCA PANEL MOUNTING JACK

CN0032-01

RCA PHONO PLUG

CN4451-01

ETHERNET COUPLER, RJ45, 8-POSITION, R/A

CN4452-01

PHONE COUPLER, RJ11, 6-POSITION, R/A

CN4452-02

RJ11, COUPLER, 4-CONDUCTOR

CN4452-03

RJ11 MALE/FEMALE SPLITTER, 4-CONDUCTOR

CN4453-01

RJ45 CROSS-OVER COUPLER

CN7507

METRIMATE RECEPTACLE, 12 PIN

CN7508

METRIMATE PLUG, 12 PIN

EC0050-01

566MHz, CPU

EC0051-01

14", I/O USB CABLE

EC0051-02

I/O USB CABLE, 3'

EC0053-02

18" RIBBON CABLE, ATA100, 40P/80 CONDUCTOR

EC0053-03

17 5/8" RIBBON CABLE, ATA100, 40P/80 CONDUCTOR

EC0056-01

UNICORN/ITOX 64 MEG DIMM SDRAM

EC0057-01

STEREO CABLE, 3.5MM, R/A

EC0057-02

5.00L,3.5MM,R/A,STEREO CABLE

EC0059-01

17" SERIAL MODEM CABLE

EC0059-02

7: SERIAL MODEM CABLE

EC0063-01

5P,10&100MPBS ETHERNET HUB

EC0066-01

250W AMPLIFIER

EC0070-01

1.8 METER VIDEO EXTENSION CABLE

EC0072-02

CAT 5 LINE/PATCH CORD, 2', UTP

EC0072-04

LINE/PATCH CORD, 5', UTP, CAT 5

EC0072-05

84.00L,UTP,CAT 5 LINE/PATCH CORD

EC0072-06

50',UTP,CAT 5 LINE/PATCH CORD

EC0072-07

16.5",UTP,CAT 5 LINE/PATCH CORD

EC0072-09

6.00L,UTP,CAT5 LINE/PATCH CORD

EC0072-10

120.00L,UTP,CAT5 LINE/PATCH CORD

EC0074-03

50' RJ11 PHONE CABLE

EC0080-01

ELECTRO-LUMINESCENT LAMP, VIBE

EC0081-01

2000MM STEREO PCH CAB

EC0082-01

10'L,VIDEO CAB

EC0085-01

PRIMARY & SECONDARY TOUCHTUNES LIGHT SHOW

EC0086-01

TOUCHTUNES SINGLE BOARD COMPUTER

(NO DISCOUNT)

EC0087-01

JUKEBOX REMOTE CONTROL TRANSMITTER, JUKEBOX

EC0088-02

JUKEBOX REMOTE CONTROL RECEIVER BOARD

EC0091-01

8.00L,MON CTLR EXT CAB

EC0092-01

POWER ENTRY W/ LINE FILTER, AC INPUT & ON/OFF SWITCH

EC0092-02

POWER ENTRY W/ LINE FILTER, AC INPUT & ON/OFF SWITCH

EC0093-01

3.00L, DC POWER HARNESS

EC0094-01

16.00L,USB I/O CABLE

EC0095-01

6.00L, MODEM AUDIO CABLE

EC0096-01

28.00L,VGA CABLE

EC0096-02

59.00L, VGA CABLE

EC0097-01

21.00L,OSD CABLE

Megatouch FORCE Parts List continued

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Item

Description

EC0097-02

36.00L,OSD CABLE

EC0098-01

9.00L, MODEM CABLE

EC0098-02

62.00L, MODEM CABLE

EC0099-01

7.00L,FAN ASSEMBLY

EC0100-01

SNAP-IN COUNTER ASSEMBLY

EC0101-01

SPEAKER ASSEMBLY,DUAL,EVO

EC0102-01

CABLE, SETUP/CALIBRATE/KEY,EVO

EC0102-02

66.00L,SETUP/CAL CAB,FUSION

EC0103-01

6.00L,USER INTERFACE USB CAB

EC0104-01

27.00L, ELECTRONIC COIN REJECTOR HARNESS, FUSION

EC0104-02

37.00L,E/CREJ HARN

EC0105-01

WATCHDOG/POWER-ON HARNESS

EC0106-01

12VDC JUMPER HARNESS

EC0107-01

3.00L,+5VDC MATING HARN

EC0108-01

AC/STACKER HARNESS, EVO

EC0109-01

4.00L, AC JUMPER WIRE

EC0110-01

59.00L, DUAL SPEAKER HARNESS, FUSION

EC0111-01

5.00L, COUNTER EXTENSION HARNESS, FUSION

EC0112-01

DC POWER CABLE, LCD, TOUCHSCREEN, FUSION

EC0113-01

3.00L,I/O POWER HARNESS

EC0114-01

SECONDARY AC CABLE, FUSION

EC0115-01

PRIMARY AC CABLE, FUSION

EC0117-01

7.00L,GROUND CABLE

EC0127-01

LED LIGHT BD (BLUE LED)

EC0128-01

ROPE LIGHT & CONTROLLER

EC0131-01

F-LMP,U3a (FLURO LMP)

EC2001

USA POWER CORD W/ DTCH IEC CONNECTOR, FUSION

EC2004-02

2MTR, UK<IEC, POWER CORD, SJT, FUSION

EC2008-01

USA POWER CORD, W/ DTCH R/A IEC CONN

EC2011-04

7.00L, INTERNATIONAL IEC POWER CORD, FUSION

EC2014-01

5-POS,OUT,IEC PANEL MOUNTING CONNECTOR

EC2015-02

INTERNATIONAL POWER CORD, 9" R/A

EC2015-03

INTERNATIONAL POWER CORD, 6", R/A

EC2015-05

INTERNATIONAL POWER CORD, 12", R/A

EC2018-01

SJT,USA,R/A IEC POWER CORD

EC2019-01

16AWG,US/IEC,SJT, POWER CORD

EC2020-01

90.00L,US<IEC,PWRCD

EC2198-01

CENTRONIC RCPT-IDE-POWER, 12"

EC2198-05

CENTRONIC RCPT-IDE-POWER, 4.50"

EC2201-01

36.00L PWRCD,6 POSN,15A,PWR STP

EC2660

.25D HEAT SHRINK TUBING, BLACK

EC3040

2A CIRCUIT BREAKER

EC3040-02

6A,PANEL MOUNTING,CB

EC5145-01

40A,12V RELAY

EC6103

STARTER - 8W

EC6109

FLUORESCENT LAMP STARTER, 220-240V

EC6111

STARTER SOCKET W/ CLIPS

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

EC6112-01

LAMP SOCKET FOR F6T5

EC6914-03

SOLID FERRITE CORE FOR .735OD X .400ID BB CABLE

EC7016-01

BALLAST, 120V/60HZ, 6W

EC7016-02

BALLAST, 220V/50HZ, 6W

EC7076-02

STM, 500VAC, ISOLATION TRANSFORMER

EC7076-03

650VAC, ISOLATION TRANSFORMER

EC7077-01

130VAC, ISOLATION TRANSFORMER

EC7529-02

60W,+12VDC,OPEN FR,PWRSPLY

EC7531-03

POWER SUPPLY, 110W ±12, +5, +3.3, AC-ON

EC7536-01

125W ±12,±5,+3.3, POWER SUPPLY

EC9100

AA ALK BATTERY

EC9154

FROG EYE COUNTER, 12V

EC9154-03

FROG EYE COUNTER, 12V, HMI, STG@0

EC9236

RING LUG #6 STUD INSL. 10-12

EC9250

8 OHM SPEAKER, 4"

EC9257-01

SHLD,50MMx90MM RECT,8-OHM S

EC9258-01

12" SUBWOOFER

EC9259-01

200W SPEAKER, PR

EC9304-01

LINE FILTER, 6A, RFI, IEC & FASTON

EC9377-08

13" VGA CRT MONITOR, R/A CONN MOUNTING

EC9381-02

LCD DISPLAY, 15", XGA, R/A CONN MOUNTING

(NO DISCOUNT)

EC9381-04

15" LCD DISPLAY, XGA

(NO DISCOUNT)

EC9382-01

19" VGA DIGITAL MONITOR

EC9382-01-01

19" VGA DIGITAL MONITOR CHASSIS

EC9383-01

FS,19"VGA MONITOR

EC9384-02

17" LCD DISPLAY, FUSION

(NO DISCOUNT)

EC9387-01

15" VGA MONITOR

EC9387-01-01

15" VGA MONITOR CHASSIS

EC9401-09

BBRG,RFI,SKT370,21CFM, CPU FAN

EC9402-03

3",42.5CFM,12V,FAN

EC9403-01

10 CFM FAN, 50MM, 12V

EC9404-01

60MM, 12V, 25 CU. FT./MINUTE FAN

EC9411-02

3",22<25CFM, 110V, FAN, TUBAXIAL

EC9790-01

$1/2/5, 500 DOWN BILL STACKER, AE2000, MARS

EC9796-01

$1/2/5, 500 BILL STACKER, AE2411, MARS BILL ACCEPTOR

EC9796-04

MARS BILL ACCEPTOR, $1/2/5, 300 STACKER, AE2000

EC9796-06

US, MARS 700 STACKER,$1/$2/$5B/A,AE2411

EC9840-08

R/A CONN,26.00L,SMT4,TOUCHSCREN CONTROLLER

EC9840-09

MICROTOUCH SMT4 TOUCHSCREEN CONTROLLER, 96"

EC9840-10

MICROTOUCH SMT4 TOUCHSCREEN CONTROLLER, 144"

EC9844-01

19" TOUCHSCREEN OVERLAY

EC9850-03

15" TOUCHSCREEN OVERLAY, CRVD

EC9850-04

15" TOUCHSCREEN OVERLAY, W/ 12" CABLE, W/O ESD

EC9850-05

FLAT SCREEN, 19" TOUCHSCREEN OVERLAY

EC9851-02

FLAT SCREEN, 17" TOUCHSCREEN OVERLAY

GL0016-01

SPEAKER COVER

GL0018-01

DOMED NAMEPLATE

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

GL0023-01

FORCE STICKER, DOME

GL0025-01

MERIT LOGO OVERLAY, VIBE

GL0025-03

EVO,MERIT LOGO OVERLAY

GL0030-03

FORCE 2004 MARQUEE, JUKEBOX

GL0034-02

FORCE 2005 MARQUEE, FUSION

GL0035-01

MEGATOUCH FRONT DECAL, FUSION

GL0035-01

SYSTEM MEGATOUCH FRONT DECAL, FUSION

GL0036-01

LEFT SIDE PANEL DECAL, FUSION

GL0036-02

RIGHT SIDE PANEL DECAL, FUSION

GL0037-01

CLEAR MARQUEE, FUSION (FRONT)

GL0037-02

CLEAR MARQUEE, FUSION (BACK)

GL0038-01

CLEAR MARQUEE,VIDEO MODULE,EVO

GL0039-01

MERIT NAMEPLATE,FUSION

GL0040-01

B/A COVER DECAL, FUSION

GL0041-01

BASE DECAL, TOWER MODULE,EVO

GL0044-01

LEFT SIDE PANEL DECAL, FUSION

GL0044-02

RIGHT SIDE PANEL DECAL, FUSION

GL2411-05

CLEAR PLEXI, 12.27x 8.28

GL2411-06

CLEAR PLEXI, 12.32 x 8.32 x .177

GL2414-01

CLEAR MARQUEE HOLDER

GL2431-04

FORCE MARQUEE

GL2432-05

FORCE 2004 MARQUEE, UPRIGHT

GL2435-01

RAINBOW S/PANEL, JUKEBOX

GL2436-01

OVL,CLR MARQUEE, JUKEBOX

GL2442-01

TOP CLR LT PANEL, JUKEBOX

GL3016-04

FORCE DECAL, UPRIGHT (NON-FUSION)

GL3016-05

FULL FORCE FRONT DECAL

GL3016-06

FORCE FRONT DECAL

GL3100-18

FORCE DECAL

GL3100-47

FORCE 2005 CTOP SIDE PANEL DECAL

GL3103-01

LEFT SIDE DECAL, VIPS

GL3103-02

RIGHT SIDE DECAL, VIPS

GL3103-03

MR VIPS LOGO DECAL

GL3104-01

PLAY'N WIN' DECAL, VIPS

GL3105-01

INSTANT REDEMPTION' DECAL, VIPS

GL3106-01

WIN A PRIZE' DECAL, VIPS

GL3107-03

CENTER ARROW PRIZE DECAL, VIPS

GL3108-01

PRIZE MATRIX' DECAL, VIPS

HW0003-01

BILL ACCEPTOR & COINBOX BUTTON

HW0004-01-0A

BILL ACCEPTOR & COINBOX BEZEL

HW0022-03

MODIFIED BEZEL, MARS 2000 BILL ACCEPTOR

HW0031-01

BEZEL TRIM, REAR

HW0035-01

16L" DRAWER SLIDE

HW0037-01

MOUNTING BRACKET, 12GA STL, 3x3, .25D

HW0041-01

MAGNETIC TAPE, HD, W/PSA, 1"W x .06T

HW0056-01

HINGE, VIBE

HW0057-02

4-7/8x2-1/2,VHB PSA FAN GUARD, VIBE

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

HW0061-01

SPILL COVER, UPRIGHT W/ COIN DOOR

HW0081-05

18" COATED WIRE CABLE W/ RING LUGS

HW0081-06

14.5" COATED WRE CABLE W/ RING LUGS

HW0100-01

15P,D-SUB MALE CONNECTOR COVER

HW0100-02

PROTECTIVE COVER, MALE CONNECTOR, 9P, D-SUB

HW0103-01

FOAM PAD, SUBWOOFER BRACKET, SS, JUKEBOX

HW0104-01

FOAM PAD, SUBWOOFER, SS, JUKEBOX

HW0105-01

TRANSFORMER COVER, MEGATUNES

HW0106-01

FLUORESCENT LAMP COVER, JUKEBOX

HW0107-01

LCD ANLG<DGTL PCB CVR,X1a

HW0108-01

10" X 15" FOAM PAD, JUKEBOX

HW0117-01

2.38x2.38, FAN GUARD FOR 60MM FAN, FUSION

HW0900-01

FORCR MOTHERBOARD FISH PAPER

HW0901-01

7.00Lx1.25Wx.02T,PSA,FORMEX PL

HW1107-03

10-24x1.63L BLACK OXIDE CARRIAGE BOLT, FUSION

HW1110

10-24x1.25L BLACK OXIDE CARRIAGE BOLT, FUSION

HW1114

10-24x2.00L BLACK OXIDE CARRIAGE BOLT, FUSION

HW1310

U BOLT, 1/4-20x1-1/4

HW1310-03

1/4-20X1.75IBHx.75IS U BOLT

HW1330

HEX BOLT, 1/4-20 x 1-1/2

HW1501-01

COTTER PIN, M2 DIA x 14MM L

HW2045

.370<.430DIA, SJT, STRAIN RELIEF, FUSION

HW3070-03

4-40 HEXNUT

HW3151

NYLON THUMBNUT, 6-32

HW3250

10-24 HEXNUT

HW4201

6-32x1/4L PAN/PHL SEMS SCREW

HW4201-07

6-32 x 5/16l PAN/PHL SEMS SCREW

HW4207

PAN/PHL MACHINE SCREW, 6-32x1/4, BLK

HW4497-02

10-24X 1.25L PAN/PHL MACHINE SCREW

HW5554-02

3/64Tx5/32IDx9/16OD FLAT FENDER WASHER

HW5658-01

.31SDx.06Lx.25IDx.44OD SHW,FBR

HW6051-01

SPACER, .168ID x .25OD x .08L

HW8018-02

ANTI-SKID PAD, 11.5D, W/6.0 C/O

HW8018-03

2.00IDx10.00OD,AS PAD

HW8031-01

COIN ENTRY GASKET

HW8059-01

FRONT & REAR BEZEL GASKET, FM, W/PSA, RADION

HW8062-01

REAR DOOR GASKET, FM, W/PSA

HW8066-01

.38Wx.06T, POLYETHYLENE FOAM TAPE,BLK,BS

HW8067

.50Wx.03T, POLYETHYLENE FOAM TAPE,BLK,BS

HW8067-02

FOAM TAPE, 1/2W x 1/8T, BLK, PSA BS

HW8120-02

BUTTON HEAD RIVET, .19-.25GR x.12DIA, ALU

HW8159-01

$.25 MECHANICAL COIN REJECTOR, IMONEX 950

HW8159-02

BACK CHAN, MECHANICAL COIN REJECTOR, IMONEX C4

HW8171-01

PCB GUIDE, SNPN, DP CHAN, 8"L

HW8227-04

SMALL COINBOX W/ PLASTIC O/U COIN DOOR

HW8249

25¢ MECH COIN REJECTOR W/ MTG FRONT PLATE

HW8312-02

SPRING, COMPRESSION, SST, .48OD x 1.50L

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

HW8312-03

SPRING, .42OD x 1.25L, COMPRESSION

HW8313-01

1/4ODx1-3/4L STAINLESS STEEL EXTENSION SPRING

HW8314-01

EXTENSION SPRING, EXT, SST, .24OD X3.50L

HW8314-02

EXTENSION SPRING, .19OD x .63L

HW8317-00

UNPROGRAMMED & PROGRAMMABLE MARS COIN REJ.

HW8317-XX

ELECTRONIC COIN MECH TD330

HW8319-04

UK ELECTRONIC COIN REJECTOR, 10/20/50P & 1/2£, G13, 330

HW8327-01

EXT SPRING, 3/16OD X 1" L

HW8333-XX

ELECTRONIC COIN MECH, WET DECK

HW8334-01

.19ODx4.13L,OPEN-END EXTENSION SPRING

HW8340-01

COIN BAG

HW8341-01

COIN BAG, VIBE w/ COIN

HW8401-01

FLAT HANDLE POCKET PULL, 5.0, .06T MOUNTING

HW8401-02

POCKET PULL, 3-1/4", .06T MOUNTING, FLAT HANDLE

HW8402-01

HANDLE, 5.50L/10-32 MOUNTING x.31D x 1.50H

HW8403-01

2-3/4 CHEST HANDLE

HW8423-01

SAFETY CLIP FOR 10MM GAS SPR BSKT END FTG, FUSION

HW8425-05

75LB,7.25" STROKE, EXTN GAS SPR W/ BALL STD & SKT FTGS

HW8440-01

.63ODx2.66L, SS CLOSED-END CMPRSN SPR, FUSION

HW8441-01

.48ODx.88L, SS PRCSN CLOSED-END CMPRSN SPR, FUSION

HW8442-01

GAS SPR MTG BRKT FOR 10MM BALL SKT END FTG, FUSION

HW8712-01

KEYED-SAME SLIDING DOOR LOCK

HW8716

564 LOCK, 1 3/8L, STRAIGHT CAM

HW8721

564 LOCK, 7/8L, W/ JAM NUT

HW8722-01

VIPS LOCKS - REAR DOOR

HW8722-02

VIPS LOCKS - DISPLAY CASE

HW8727

KEYED LOCK, 1-1/8L, CAPTIVE KEY, STRAIGHT CAM

HW8727-02

KEYED LOCK, 1.38L, CAPTIVE KEY, W/O CAM

HW8731

KEYED LOCK, 7/8L, W/ JAM NUT, 90°

HW8733-03

KEYED LOCK, 5/8L, CAPTIVE KEY, HI SECURITY, W/O CAM

HW8733-04

KEYED LOCK, 1.38, CAPTIVE KEY, HI SECURITY, W/O CAM

HW8733-05

KEYED LOCK, 7/8L, CAPTIVE KEY, HI SECURITY, W/O CAM

HW8733-07

KEYED LOCK, .88L, CAPTIVE KEY, CCW,H/S,-CAM

HW8734-01

564 LOCK, 5/8L, W/O CAM

HW8741

CASH DOOR LOCK, 1/2L, CIRC, BENT CAM

HW8848-01

B/A FISH PAPER,TOWER MODULE, EVO

HW8854

5/8DIA,13/64 MTGHOLE HARN CLIP

HW8880-02

STANDOFF, TWIST LOCK, .75/.85BDL, .187DIA

HW8911-02

SPRING PIN, .188OD x .50L

HW8953-03

MODIFIED 13" MONITOR BEZEL

HW8960-02

3/8-16 X 3L LEG LEVELER W/ 3/8-16 NUT

HW8989

FAN GUARD, 2.8"

HW8993-02

LAZY SUSAN, 12" DIAMETER, 15° STOPS

HW9030-01

SHOCK MOUNT GROMMET, .245ID x .755OD

HW9101-01

.303GDx.039GW E RING

HW9252-02

2 x 2 VELCRO, HOOK & LOOP

HW9252-03

1 x 3 VELCRO, HOOK & LOOP

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

HW9420

9x11 VINYL SHEET HOLDER

HW9461-03

SIGN HOLDER, 4X12

HW9996-01

10-32M, 5/8" DIAMETER PHENOLIC KNURLED RIM KNOB

HW9998-01

10-32x.50L,KNOB,CLAMPING MACHINE SCREW

KOV-105-102-01 FORCE VIDEO MODULE OEM KIT

(NO DISCOUNT)

KOV-105-104-01 VIBE PROCESSOR MODULE

(NO DISCOUNT)

KOV-105-104-02 FORCE PROCESSOR MOD OEM KIT, VIBE w/ COIN

(NO DISCOUNT)

KOV-105-105-01 COIN REJ.-READY VID MOD OEM KT, VIBE w/ COIN

(NO DISCOUNT)

KUV-107-001

BILL ACCEPTOR COINBOX, .25/$1/$2/$5

(NO DISCOUNT)

LB1030-01

9", 6 WATT FLUORESCENT CLOCKWISE BULB

MP0001-09

LEFT SIDE COVER

MP0001-10

RIGHT SIDE COVER

MP0002-07

TOP COVER, 15", COIN ENTRY

MP0005-08

FRONT COVER

MP0009-05

BEZEL, 15" LCD

MP0010-01

BEARING, DISPLAY PIVOT

MP0011-01

BEARING SEAT, DISPLAY PIVOT

MP0013-03

FRONT COVER

MP0014-01

FRONT BEZEL

MP0015-01

REAR BEZEL

MP0016-01

RADION BASE

MP0017-01

REAR DOOR

MP0018-01

LEFT SIDE COVER

MP0018-02

RIGHT SIDE COVER

MP0019-01

COIN ENTRY PLATE

MP0020-01

COIN RETURN LEVER

MP0021-02

MARS BILL ACCEPTOR COMBO PLATE

MP0024-01

MONITOR BEZEL

MP0025-01

MONITOR BEZEL

MP0026-01

CLEAR INSERT, VIBE

MP0027-01

MONITOR BEZEL, VIBE

MP0028-01

REAR ENCLOSURE, VIBE

MP0029-01

CENTRONICS COVER

MP0030-01

PLASTIC CREDIT CARD BLANKING PLATE, VIBE

MP0034-01

COIN GUARD, RADION

MP0035-01

MONITOR BEZEL, JUKEBOX

MP0036-01

LOWER BEZEL, JUKEBOX

MP0037-01

REAR ENCLOSURE, VIBE w/ COIN

MP0038-01

COIN CUP INSERT, VIBE w/ COIN

MP0039-01

COIN REJECTOR BRACKET, VIBE w/ COIN

MP0040-02

COIN BAG COLLAR, VIBE w/ COIN

MP0041-01

COIN RETURN BUTTON, VIBE w/ COIN

MP0044-01

MONITOR BEZEL,FUSION

MP0045-01

NOSE,B/A,TOWER MODULE,EVO

MP0047-01

COIN RETURN CHUTE,TOWER MODULE,EVO

MP0048-01

POD,TWR MDL,EVO

MP0049-01

FACE,CN ENT,TWR MDL,EVO

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

MP0050-01

FR,ENCL,VID MDL,EVO

MP0051-01

REAR,ENCL,VID MDL,EVO

MP0053-01

COIN RETURN KNOB,FUSION

MP0054-02

MON BZL, FUSION

MW0009-02-0D COUNTERTOP CHASSIS
MW0010-02-0J

DISPLAY FRAME

MW0013-01-0C TOP, CLASSIC
MW0014-01-0B LATCH PLATE, (RIGHT)
MW0014-02-0B LATCH PLATE, (LEFT)
MW0015-01

LOCK BRACKET

MW0016-01-0C DOOR, CLASSIC
MW0020-01-0B COIN CHUTE, ENTRY, LEFT
MW0021-01

COIN CHUTE, ENTRY, RIGHT

MW0023-01

LOCK BOLT, 13.64"L

MW0023-04

BOLT, LOCK, 7.99" L

MW0024-01

CAM LOCK

MW0038-01

CORD CLAMP

MW0043-01

COINBOX STOP

MW0051-01

LINKAGE, COIN RETURN

MW0052-01-0A BILL ACCEPTOR & COINBOX DOOR
MW0053-01

EXTENSION, BILL ACCEPTOR & COINBOX BUTTON

MW0055-01

COINBOX & BILL ACCEPTOR CHASSIS

MW0061-02

FAN PROTECTOR COVER,

MW0092-01-0A MARQUEE FRAME
MW0093-01-0B MARQUEE CLAMP
MW0095-01

STAY ARM

MW0095-03

.19T,STAY ARM,FUSION

MW0097-01-0A TAMPER PROOF BEZEL BRACKET
MW0098-01

STAY ARM HAT BRACKET, FUSION

MW0098-01-0A STAY ARM HAT BRACKET
MW0118-01-0B SMILEY BRACKET
MW0119-03

MECHANICAL COIN REJECTOR BRACKET, RD

MW0124-01-0B HINGE, UPRIGHT
MW0126-01-0D FRONT LOCK/SPEAKER PANEL GRILL
MW0129-01

COVER PLATE, B/A OPENING

MW0133-01-0A FLUORESCENT LAMP BRACKET
MW0138-01-0B 2 POINT LOCK BRACE
MW0221-01

ANGLE,SCTY REINF,UR,XL5

MW0224-01

ELECTRONIC COIN REJECTOR BRACKET, L

MW0241-01

BRACKET, TOP, MAIN

MW0242-01

BRACKET, SIDE PANEL, L

MW0242-02

BRACKET, SIDE PANEL, R

MW0243-01

COINBOX DRAWER

MW0244-04

DRAWER FACE

MW0245-01

DRAWER COVER

MW0246-01

UPPER LATCH CLIP

MW0246-02

LOWER LATCH CLIP

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

MW0248-01

LOWER BEZEL BRACKET

MW0253-01

LOCK BAR, COINBOX DOOR

MW0254-01

CAM LOCK, COINBOX DOOR

MW0260-01

LATCH, UPPER-LEFT SIDE PANEL

MW0260-02

LATCH, LOWER-LEFT SIDE PANEL

MW0260-03

LATCH, UPPER-RIGHT SIDE PANEL

MW0260-04

LATCH, LOWER-RIGHT SIDE PANEL

MW0281-06

POWER ENTRY BRACKET

MW0298-01

BRACE/MARQUEE BRACKET

MW0299-01

CRT SHELF BRACKET

MW0305-01

COIN CHUTE, SIDE MOUNT

MW0321-01

PLATE, SIDE LATCH

MW0322-01

REAR DOOR CAM, 3 PT

MW0323-01

REAR DOOR LOCK BAR

MW0324-02

COIN ENTRY PLATE, TILT

MW0325-01

COIN MECH BRACKET

MW0326-01

COIN REJECTOR SHAFT

MW0327-01

COIN RETURN CHUTE

MW0333-01

COIN MECH CLIP, LEFT

MW0333-02

COIN MECH CLIP, RIGHT

MW0339-01

COIN RETURN CUP, TILT

MW0343-01

COIN RTN CUP FLAP

MW0345-01

METER BRACKET

MW0346-01

CHASSIS, MAIN, ATX

MW0350-01

DISPLAY CLIP

MW0351-04

REAR DOOR

MW0361-01

FAN BRACKET

MW0362-02

ELECTRONIC SHELF

MW0366-01

COINBOX/CRT BRACKET

MW0367-01

POWER ENTRY/COUPLER PLATE

MW0374-01

COINBOX, UPRIGHT

MW0378-01

MARS BILL ACCEPTOR BRACKET

MW0379-01

BILL ACCEPTOR CAM, 5/8OFS

MW0382-01

LEG LEVELER ADAPTER, UPRIGHT

MW0394-01

LEFT LCD BRACKET

MW0394-02

RIGHT LCD BRACKET

MW0407-01

LABEL BRACKET

MW0425-01

MAIN CHASSIS

MW0426-02

HINGE BRACKET

MW0427-01

COINBOX DRAWER

MW0428-01

DRAWER, COVER

MW0429-01

LOWER BEZEL BRACKET

MW0431-01

BILL ACCEPTOR BRACKET

MW0432-01

BEZEL CLAMP BRACKET

MW0435-01

BILL ACCEPTOR CLAMP, TOP

MW0436-01

BILL ACCEPTOR CLAMP, BOTTOM

MW0443-01

COIN CHUTE FUNNEL, UPRIGHT

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

MW0447-01

ATX POWER SUPPLY BRACKET

MW0467-01

MICROTOUCH CONTROLLER BRACKET

MW0469-01

POWER SUPPLY MOUNTING BRACKET

MW0470-01

COIN CHUTE

MW0471-01

COIN RETURN CHUTE

MW0472-01

CAM, L, DOOR

MW0475-01

DOMESTIC COINBOX

MW0476-01

I/O BRACKET

MW0479-01

COIN RETURN ARM

MW0482-01

LEFT LOCKING CAM

MW0483-01

REAR DOOR HINGE

MW0486-01

SHORT LOCKING BAR

MW0486-02

LONG LOCKING BAR

MW0487-01

MOTHERBOARD TRAY

MW0488-01

COIN OPTION BRACKET

MW0489-01

FAN BRACKET, 60MM

MW0491-01

COIN RETURN LEVER

MW0493-01

MOTHERBOARD TRAY, W/B/A

MW0494-01

HARD DRIVE BRACKET

MW0495-01

HARD DRIVE FAN BRACKET, W/B/A

MW0496-01

MOTHERBOARD TRAY

MW0497-01

I/O & HARD DRIVE BRACKET

MW0498-01

REAR DOOR CAM

MW0499-01

BRACKET, DUAL 50MM FANS

MW0500-01

SPILL PLATE, REAR DOOR

MW0502-01

CURVED STRAP HINGE

MW0503-01

STRAIGHT STRAP HINGE

MW0509-01

LONG LOCKING BAR RETAINING PLATE

MW0510-01

COINBOX LOCK CAM

MW0516-01

SLIDE PLATE

MW0520-01

I/O BRACKET

MW0521-01

BILL ACCEPTOR ALIGN BRACKET

MW0542-01

HARD DRIVE BRACKET, RADION

MW0543-01

FAN GUARD W/ SWITCH OPENING

MW0544-01

SPEAKER GRILL, UPRIGHT W/ COIN DOOR

MW0545-01

SIGN HOLDER, UPRIGHT W/ COIN DOOR

MW0546-01

MOTHERBOARD CHASSIS, UPRIGHT W/ COIN DOOR

MW0559-01

ESCUTCHEON, UPRIGHT

MW0560-01

B/A COVER, UPRIGHT W/ COIN DOOR

MW0561-01

B/A COVER BRACKET

MW0566-01

OVERSIZED COINBOX, RADION

MW0567-01

LEFT SPEAKER BRACKET, VIBE

MW0567-02

RIGHT SPEAKER BRACKET, VIBE

MW0568-01

SWITCH CONNECTOR BRACKET, VIBE

MW0572-01

CHASSIS, VIBE

MW0573-01

HARD DRIVE BRACKET

MW0575-02

PROCESSOR ENCLOSURE LID, VIBE

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

MW0575-03

PROCESSOR ENCLOSURE BASE, VIBE

MW0577-01

LCD BRACKET, VIBE

MW0578-01

METAL CREDIT CARD BACKING PLATE, VIBE

MW0584-01

.39 OFFSET LOCK CAM, VIBE

MW0597-01

CAM, BILL ACCEPTOR LOCK BRACKET, VIBE

MW0610-01

CAM, CATCH, LOCK BRACKET, VIBE

MW0611-01

LOCK PLUNGER, VIBE

MW0612-01

WIRE ENTRY PLATE, VIBE

MW0613-01

BILL ACCEPTOR LOCK BRACKET, VIBE

MW0615-01

SPEAKER BRACKET, JUKEBOX

MW0616-01

COMM INTFC PANEL, JUKEBOX

MW0617-01

SW BRACKET, JUKEBOX

MW0618-01

TOUCHTUNES MODULE MOUNTING PLATE, JUKEBOX

MW0619-01

RISER MOUNTING BRACKET, JUKEBOX

MW0621-01

IEC OUTLET MODULE MOUNTING BRACKET

MW0625-01

LEFT JUKEBOX MONITOR MOUNTING BRACKET

MW0625-02

RIGHT JUKEBOX MONITOR MOUNTING BRACKET

MW0626-01

JUKEBOX DOOR FRAME ASSEMBLY

MW0629-01

JUKEBOX CARD READER BLANKING PLATE

MW0631-01

JUKEBOX LIGHT SHOW MOUNTING BRACKET

MW0633-01

SUBWOOFER BRACKET, JUKEBOX

MW0634-01

FAN MOUNTING BRACKET, JUKEBOX

MW0635-01

DL FAN MOUNTING BRACKET, JUKEBOX

MW0637-01

REAR PANEL, SS, JUKEBOX

MW0638-01

LOCK CAM,SS, JUKEBOX

MW0639-01

INTERNAL AUDIO BRACKET,SS, JUKEBOX

MW0640-01

SUBWOOFER BRACKET

MW0641-01

TRANSFORMER BRACKET

MW0642-01

AMPLIFIER BRACKET,SS, JUKEBOX

MW0643-01

18Lx5.25Wx.05T PERF PANEL

MW0645-01

ENET BRACKET, MEGATUNES, JUKEBOX

MW0646-01

TRANSFORMER BRACKET, MEGATUNES, JUKEBOX

MW0647-01

TRANSFORMER BRACKET, MEGATUNES, JUKEBOX

MW0649-01

ACCESS PANEL, VIBE

MW0650-01

LOCK CATCH BRACKET, JUKEBOX

MW0651-01

RCPT, LOCK CATCH BRACKET, JUKEBOX

MW0652-01

LOCK BRACKET, VIBE

MW0653-01

COIN BAG BRACKET, JUKEBOX

MW0655-01

CATCH, LOCK BRACKET, VIBE

MW0657-01

CHASSIS, MEGATUNES

MW0663-01

COIN RETURN CHUTE, VIBE w/ COIN

MW0664-01

TILT BRACKET, VIBE w/ COIN

MW0665-01

RIGHT COIN REJECTOR HANDLE, VIBE w/ COIN

MW0665-02

LEFT COIN REJECTOR HANDLE, VIBE w/ COIN

MW0666-01

LOCK BRACKET CATCH, VIBE w/ COIN

MW0667-01

LOCK BRACKET BASE, VIBE w/ COIN

MW0668-01

ELECTRONIC COIN REJECTOR BRACKET, VIBE w/ COIN

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

MW0669-01

SWITCH/CONNECTOR BRACKET, VIBE w/ COIN

MW0670-01

FACEPLATE, VIBE w/ COIN

MW0671-01

LOCK PLUNGER, VIBE w/ COIN

MW0672-01

WIRE ENT PLATE, VIBE w/ COIN

MW0679-01

.98" OFFSET LOCK CAM, VIBE w/ COIN

MW0680-01

RIBBON CABLE ADAPTER PLATE, VIBE w/ COIN

MW0690-01

CREDIT CARD COVER,FUSION

MW0691-01

COIN ENTRY PLATE,FUSION

MW0695-01

MAIN<RETURN COIN CHUTE CUP,FUSION

MW0696-01

MAIN ASSEMBLY,COIN CHUTE,FUSION

MW0697-01

ENTRY<RTN,COIN CHUTE,FUSION

MW0699-01

COIN RETURN CUP ASSEMBLY,FUSION

MW0700-01

COIN BOX,FUSION

MW0701-01

STAY ARM UPR BRACKET,FUSION

MW0702-01

POWER SUPPLY HOLDER,FUSION

MW0704-01

GAME COUNTER BRACKET,FUSION

MW0708-01

INNER CURRENCY HATCH,FUSION

MW0709-01

B/A MOUTING PLATE,FUSION

MW0710-01

MARS B/A SHROUD,FUSION

MW0712-01

FRONT ADAPTER PLATE,FUSION

MW0714-01

UPPER,FOAM HOLDER,FUSION

MW0715-01

LOWER,FOAM HOLDER,FUSION

MW0718-01

POWER ENTRY MODULE PANEL,FUSION

MW0718-02

MUSIC & POWER ENTRY MODULE PNL,FUSION

MW0720-01

B/A-RDY,TWR MDL,EVO

MW0720-02

COIN REJECTOR-READY TOWER MODULE,EVO

MW0721-01

TOWER MODULE CAP,EVO

MW0722-01

TOWER MODULE BASE, EVO

MW0724-01

REAR MTG BRACKET, POD/CAP TWR MDL,EVO

MW0725-01

FRONT MTG BRACKET, CAP, TWR MDL,EVO

MW0726-01

LOCK CAM,EVO

MW0730-01

CNBX/FAN BRKT,TWR MDL,EVO

MW0731-01

LARGE CNBX,TWR MDL,EVO

MW0732-01

COIN EXIT BRKT,TWR MDL,EVO

MW0733-01

FACE BRKT,CN ENT,TWR MDL,EVO

MW0734-01

COIN REJECTOR BRKT,TWR MDL,EVO

MW0735-01

COIN REJECTOR LEVER,TWR MDL,EVO

MW0737-01

CAST IRON WEIGHT, FUSION

MW0740-01

LCD MTG BRKT,VID MDL,EVO

MW0742-01

FRONT POD BRKT,TWR MDL,EVO

MW0743-01

SMALL CNBX,TWR MDL,EVO

MW0744-01

BRKT,SMALL CNBX,TWR MDL,EVO

MW0746-01

BRKT,COIN RETURN,TWR MDL,EVO

MW0747-01

BRKT,TOUCHSCREEN CONTROLLER,VID MDL,EVO

MW0749-01

COMMUNICATIONS MODULE COVER PANEL,VID MDL,EVO

MW0750-01

MOTHERBOARD CHASIS,FUSION

MW0751-01

COIN RETURN EXTENSION BRKT,CN RTN/FP,TWR MDL,EVO

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

MW0752-01

LWR BRKT,COIN RETURN,TWR MDL,EVO

MW0753-01

LOCK RESTRICTOR/SPACER,VID MDL,EVO

MW0754-01

ADJUSTABLE COIN LEVER EXT,FUSION

MW0755-01

B/A COVER PLATE,FUSION

MW0756-01

B/A COVER PLATE BACKING,FUSION

MW0758-01

B/A COVER,INNER CURRENCY HATCH,FUSION

MW0759-01

LCD HOLDER/SIDE EXPANDER,FUSION (LCD EXT)

MW0760-01

MECH. COIN REJECTOR HOLDER CLAMP,FUSION

MW0760-02

ELEC. COIN REJECTOR HOLDER CLAMP,FUSION

MW0761-01

COIN SWITCH REPLACEMENT CHUTE,FUSION

MW0762-01

COIN REJECTOR CHUTE,FUSION

MW0780-01

PWRSPLY BRKT,VID MDL,EVO

MW0781-01

HINGE,VID MDL,EVO

MW0782-01

BRKT,COMM MDL,VID MDL,EVO

MW0783-01

LOCK SLIDE,VID MDL,EVO

MW0789-01

OSD BOARD HINGE ARM,FUSION

MW0791-01

CASH AREA BASE GUARD,FUSION

MW0792-01

BEZEL LOCK MECH,FUSION

MW0794-01

LOCK RECEPTACLE FRAME,FUSION

MW0795-01

LOCK RECEPTACLE INSERT,FUSION

MW0797-01

BEZEL CLOSURE BASE,FUSION

MW0798-01

LCD MOUNTING BRACKET,FUSION

MW0801-01

CURRENCY DOOR LOCK CAM,FUSION

MW0802-02

MARS B/A SHROUD REAR BLANKING PLATE,FUSION

MW0805-01

BEZEL<CABINET HINGE,FUSION

MW0806-01

LOCK CATCH,FUSION

MW0807-01

COIN ACCEPTANCE CHUTE COLLAR,FUSION

MW0808-01

COIN ACCEPTANCE CHUTE MOUNTING BRACKET,FUSION

MW0809-01

COIN ACCEPTANCE CHUTE, FUSION

MW0810-01

BEZEL CLOSURE BASE REINFORCEMENT,FUSION

MW0812-01

BILL ACCEPTOR FRONT PLATE, TOWER MODULE, EVO

MW0812-02

COIN MECH FRONT PLATE, TOWER MODULE, EVO

MW0856-01

FLUORESCENT LAMP BRACKET, FUSION

MW0886-01

MONITOR BEZEL LOCK MOUNTING PLATE, FUSION

MW0887-01

CASH PANEL LOCK CATCH BRACKET, FUSION

MW0888-01

B/A<BEZEL ADAPTER BRACKET, FUSION

MW0889-01

CASH PANEL, FUSION

MW0890-01

SPEAKER PANEL, FUSION

MW0890-02

SPEAKER PANEL TRIM, FUSION

MW0891-01

BEZEL HINGE, FUSION

MW0892-01

EMI/RFI ELECTRONICS ENCLOSURE, FUSION

MW0893-01

BEZEL MOUNTING BRACKET, FUSION

MW0894-01

UPPER COIN ENTRY BRACKET, FUSION

MW0894-02

LOWER COIN ENTRY BRACKET, FUSION

MW0895-01

BEZEL LOCK CAM, FUSION

MW0896-01

CASH PANEL & REAR DOOR, LOCK CAM, FUSION

MW0897-01

3-POINT LOCK BRACKET, FUSION

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

MW0898-01

CREDIT CARD BLANKING PLATE MOUNTING BRACKET, FUSION

MW0898-02

CREDIT CARD READER MOUNTING BRACKET, FUSION

MW0899-01

3-POINT LOCK ARM, MONITOR BEZEL, FUSION

MW0902-01

FOOT COVER, FUSION

MW0904-01

DOOR NUT, FUSION

MW1720-01-0B

SPEAKER SCREEN

MW2012-01

SECURITY LOOP, R

MW2012-02

SECURITY LOOP, L

MW2013-01

DUCK BILL CAM

MW4147-01

SMALL FLUORESCENT LAMP FIXTURE ENCLOSURE

MW5000-03

DUAL METER & SWITCH BRACKET

MW5003-01

LEFT CRT ADJ BRACKET W/ CUTOUT

MW5003-03

LEFT CRT ADJ BRACKET W/O CUTOUT

MW5004-01-0A

POWER ENTRY BRACKET,U/R 19",T/S

MW5164-01

REAR DOOR HINGE, COUNTERTOP

MW5171-01

COINBOX CONN BRACKET, W/B

MW5171-02

COINBOX CONN BRACKET

PA0049-03

VIPS HARD DRIVE

PA0060-01

FRC,US MODEM

PA3021-02

FORCE 2005 HARD DRIVE

PM0212-02

COIN/COUNTRY JUMPER CHART

PM0347-01

RADION SIGN INSTALLATION INSTRUCTIONS

PM0353-03

RECESSED WALL MOUNTING TEMPLATE, VIBE w/ COIN

PM0354-01

PROCESSOR MOUNTING TEMPLATE, VIBE

PM0398-01

MOUNTING TEMPLATE, MEGATUNES

PM0409-01

VIDEO MODULE WALL MOUNTING TEMPLATE, VIBE w/ COIN

PM2417-01

BASE/WALL MTG COIN REJ. ADJUSTING LABEL, VIBE w/ COIN

PM5131-01

WARNING LABEL

PM5937-02

PATENT LABEL VIDEO GAMES

PM6063-01

$1/$2/$5 STICKER

PM6064-01

$1/$2 & $5 STICKER

PM8928-39

FORCE SIGN

PM8928-68

FORCE 2005 COUNTERTOP SIGN

PM8949-01

TOURNAMAXX READY PROMO SIGN

PM8950-07

2K5 SIGN,EVO

SA0014-03

ELECTRONIC/MANUAL COIN REJECTOR HARNESS

SA0040-08

CASH BOX ASSY, COIN & B/A READY, XL/CLASSIC

SA0047-02-0A

COIN-BILL ACCEPTOR HARNESS

SA0064-04

120V POWER ENTRY MODULE

SA0078-07

GROUND, #10 RING LUG, 17"

SA0078-10

GROUND, #6 RING LUG & #10 RING LUG, 20"

SA0078-15

GROUND, #6 RING LUG & #10 RING LUG, 7"

SA0078-23

GROUND, #10 RING LUG, 44"

SA0078-26

GROUND, #10 RING LUG, 14"

SA0078-27

GROUND, #10 RING LUG, 4"

SA0082-01

AC JUMPER HARNESS

SA0082-02

AC JUMPER HARNESS, 32"L

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

SA0096-04

POWER ENTRY W/ COUPLERS

SA0097-01

MODIFIED MARS 2000 BILL ACCEPTOR (500 STACKER)

SA0097-04

MOD MARS 2000 B/A (500 STACKER)

SA0102-03

INTERFACE, CASH SYSTEM

SA0103-07

13" VGA TOUCHSCREEN ASSEMBLY

SA0105-06

SILVER & BLACK COVER

SA0106-12

DOMESTIC POWER ENTRY ASSEMBLY

SA0108-04

MAIN HARNESS

SA0118-03

POWER EXTENSION CABLE, PCA/HARD DRIVE

SA0118-03

HARD DRIVE/CD-ROM POWER EXTENSION CABLE

SA0118-04

HARD DRIVE/CD-ROM POWER EXTENSION CABLE

SA0152-01

SMILEY HARNESS, JUMPER1

SA0152-02

SMILEY HARNESS, JUMPER2

SA0152-03

SMILEY HARNESS, JUMPER3

SA0152-04

SMILEY HARNESS, JUMPER4

SA0165-01

SWITCH COUNTER ASSEMBLY

SA0177-03-0A

FLUORESCENT LAMP FIXTURE, 6W, 220V/50HZ

SA0177-04-0A

FLUORESCENT LAMP FIXTURE, 117V/60HZ, 6W

SA0177-05

6W,117V/60HZ, FLUORESCENT LAMP ASSEMBLY

SA0177-06

6W,117V/60HZ, FLUORESCENT LAMP ASSEMBLY W/O BRKT

SA0178-02

MAIN HARNESS

SA0181-02

POWER SWITCH HARNESS

SA0183-03

COIN MECH HARNESS

SA0183-04

INTERNATIONAL COIN MECH HARNESS

SA0184-01

MARS BILL ACCEPTOR HARNESS

SA0185-03

SMILEY BILL ACCEPTOR HARNESS

SA0197-01

12V FAN ASSEMBLY, CVR/3"

SA0225-06

AC HARNESS, ATX

SA0226-04

DC POWER HARNESS, ATX

SA0226-05

DC POWER HARNESS, ATX

SA0237-04

TOP COVER, GND

SA0238-05

BOTTOM FRONT COVER

SA0238-06

BOTTOM FRONT COVER

SA0240-05

COIN DRAWER

SA0240-06

COIN DRAWER

SA0241-05

LEFT SIDE COVER

SA0241-06

RIGHT SIDE COVER

SA0242-06

DOMESTIC POWER ENTRY

SA0242-07

INTERNATIONAL POWER ENTRY ASSEMBLY

SA0250-06

POWER SHELF

SA0250-07

POWER SHELF ASSEMBLY

SA0252-04

HARNESS, AC, CIRCUIT BREAKER, ATX

SA0255-03

MECHANICAL COIN REJECTOR BRACKET ASSEMBLY

SA0260-04

ATX POWER/PCB HARNESS

SA0266-01

POWERCORD, 6" R/A, F, IEC W/F CONNECTOR, R

SA0266-02

9" R/A,F,IEC W/ F CONNECTOR, POWER CORD, R

SA0267-03

POWER SUPPLY

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

SA0268-01

METER/BRACKET

SA0279-01

COUNTERTOP FAN

SA0298-02

BILL ACCEPTOR ASSEMBLY

SA0304-01

POWER ENTRY

SA0306-01

DC DIST HARN,XL7

SA0307-01

60MM SINGLE FAN ASSEMBLY, RADION

SA0307-02

60MM SINGLE FAN ASSEMBLY, FUSION

SA0308-01

POWER SUPPLY ASSEMBLY, RADION

SA0309-01

DUAL CENTER ASSEMBLY

SA0309-02

COUNTER ASSEMBLY, RADION

SA0309-03

COUNTER ASSEMBLY, VIBE

SA0309-04

COUNTER ASSEMBLY, FUSION

SA0310-01

COUNTER HARNESS

SA0312-01

I/O, AUDIO, COUNTER ASSEMBLY

SA0313-01

SPEAKER, ASSEMBLY

SA0313-02

SPEAKER, W/22 AWG, ASSEMBLY

SA0314-01

STACKER HARNESS W/ LOCKOUT

SA0316-01

ELECTRONIC COIN REJECTOR HARNESS

SA0318-01

DC POWER HARNESS, MAIN, RADION

SA0319-01

AC CR STACKER HARNESS

SA0320-01

DUAL FAN ASSEMBLY, 50MM

SA0324-01

RIGHT SIDE PANEL, RADION

SA0325-01

LEFT SIDE PANEL, RADION

SA0326-01

REAR DOOR & BEZEL, RADION

SA0327-01

FRONT BEZEL, RADION

SA0328-01

UPPER COIN CHUTE, RADION

SA0329-02

MONITOR & TOUCHSCREEN, RADION

SA0329-03

MONITOR & TOUCHSCREEN,U3a

SA0330-12

MR VIPS HARD DRIVE & MTHBD MODULE

SA0336-01

DC Y CONN HARN

SA0338-01

DOMESTIC COINBOX & BILL ACCEPTOR

SA0338-07

OVERSIZED DOMESTIC COINBOX & BILL ACCEPTOR, RADION

SA0338-09

OVERSIZED NJ COINBOX & BILL ACCEPTOR, RADION

SA0338-10

OVERSIZED SMILEY-READY COINBOX, RADION

SA0338-11

OVERSIZED COINBOX, RADION

SA0339-01

COIN OPTION BRACKET

SA0341-01

COIN ENTRY

SA0345-01

I/O & AUDIO HARNESS, DC

SA0346-01

INTERNATIONAL AC HARNESS

SA0347-01

DOMESTIC AC HARNESS, FORCE

SA0348-01

DC/AUDIO HARNESS, FORCE

SA0349-02

MAIN AC HARNESS, FORCE

SA0350-01

DC HARNESS, I/O & VIDEO, FORCE

SA0351-01

MAIN SIGNAL HARNESS, FORCE

SA0352-01

MAIN DC HARNESS, FORCE

SA0354-01

I/O HARNESS

SA0355-01

COUNTER HARNESS

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

SA0356-01

POWER ON HARNESS

SA0361-01

ELECTRONIC COIN REJECTOR

SA0372-01

POWER ON/OFF MODULE

SA0373-01

DC MOTHERBOARD HARNESS, UPRIGHT W/ COIN DOOR

SA0375-01

AC BILL ACCEPTOR EXTENSION HARNESS

SA0376-01

I/O HARNESS, UPRIGHT W/ COIN DOOR

SA0377-01

MANUAL COIN REJECTOR HARNESS

SA0377-02

JUKEBOX, MECHANICAL COIN REJECTOR CABLE

SA0378-01

MAIN HARNESS

SA0379-01

ELECTRONIC COIN REJECTOR HARNESS

SA0386-02

9' LINKING HARNESS, VIBE

SA0387-01

AC PROCESSOR HARNESS, VIBE

SA0387-02

AC HARNESS, PROCESSOR, VIBE w/ COIN

SA0388-01

PROCESSOR HARNESS, VIBE

SA0389-01

LEFT SPEAKER, VIBE

SA0389-02

RIGHT SPEAKER, VIBE

SA0390-01

SWITCH CONNECTOR MODULE, VIBE

SA0390-02

SWITCH/CONNECTOR MODULE, VIBE w/ COIN

SA0391-01

LINKING MECHANISM, VIBE

SA0392-01

15" TOUCHSCREEN AND DISPLAY, VIBE

SA0393-01

ELECTRO-LUMINESCENT DISPLAY, VIBE

SA0393-02

ELECTRO-LUMINESCENT DISPLAY, VIBE w/ COIN

SA0399-01

VIDEO CHASSIS MODULE, VIBE

SA0400-01

DUAL 50MM FAN ASSEMBLY, VIBE

SA0402-01

PROCESSOR COVER ASSEMBLY, VIBE

SA0403-01

3-POSITION CONNECTOR & DUAL PUSH BUTTON SWITCH

SA0404-01

3" SPEAKER BRACKET, RADION

SA0405-01

DISPLAY HARNESS, VIBE

SA0406-02

9' AC HARNESS STACKER, VIBE

SA0407-02

JUKEBOX CONTROL CABLE

SA0408-02

JUKEBOX HUB POWER HARNESS

SA0410-01

LOW LEVEL AUDIO CABLE, JUKEBOX

SA0418-01

HARNESS, DC TAP, VIBE

SA0422-01

MONITOR/LIGHT AC CABLE, JUKEBOX

SA0423-02

SECONDARY AC HARNESS, FCC, JUKEBOX

SA0425-01

AC PRIMARY INLET HARNESS, JUKEBOX

SA0426-01

LIGHT SHOW EXTENSION HARNESS, JUKEBOX

SA0427-02

DC DISTRIBUTION CABLE, MEGATUNES

SA0427-03

LIGHT SHOW DC DISTRIBUTION CABLE, FCC, JUKEBOX

SA0428-02

TOUCHTUNES CONTROL BOARD HARNESS, MEGATUNES

SA0428-03

TOUCHTUNES CONTROL BOARD HARNESS, FCC, JUKEBOX

SA0429-01

ELECTRO-LUMINESCENT ASSEMBLY, VIBE

SA0429-02

ELECTRO-LUMINESCENT ASSEMBLY, VIBE w/ COIN

SA0431-01

COMMUNICATIONS INTERFACE MODULE, JUKEBOX

SA0438-01

AUDIO GAME HARNESS, JUKEBOX

SA0439-02

DC DISTRIBUTION HARNESS, FCC, JUKEBOX

SA0440-04

VER3,SIG&RLY HARN,SP2

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

SA0442-01

PRIMARY AC HARNESS, MEGATUNES

SA0442-02

SECONDARY AC HARNESS, MEGATUNES

SA0443-01

AC FAN ASSEMBLY, JUKEBOX

SA0444-01

COUNTER HARNESS, JUKEBOX

SA0445-01

HUB PWR CABLE, MEGATUNES

SA0446-01

ANTENNA CABLE

SA0447-01

30" RED & BLACK PAIRED CABLE

SA0449-01

LOCK MECHANISM, VIBE w/ COIN

SA0451-01

COIN REJECTOR, VIBE w/ COIN

SA0452-01

COIN REJECTOR-READY ASSEMBLY, VIBE w/ COIN

SA0455-02

6 CH. ELEC. COIN REJ. CAB., VIDEO MDL, VIBE w/ COIN

SA0456-01

ELECTRONIC COIN REJ. HARNESS, PROC. MDL, VIBE w/ COIN

SA0458-01

AC CAB,SP2

SA0459-02

CAB,60"L,AUD EXT,SP2

SA0467-02

B/A-RDY,TWR MDL,EVO

SA0469-01

15.00 DSPL, SAM VID MDL,EVO

(NO DISCOUNT)

SA0469-03

V2,17" TOUCHSCREN & MONITOR,FUSION

(NO DISCOUNT)

SA0469-04

V2,17 MONITOR,FUSION

(NO DISCOUNT)

SA0469-05

15" DISPLAY, KORTEK VIDEO MODULE,EVO

(NO DISCOUNT)

SA0469-09

17" DISPLAY & TOUCHSCREEN, FUSION

(NO DISCOUNT)

SA0470-01

4.00L,52MM FAN ASSY,EVO

SA0473-01

MECH. COIN REJECTOR HARNESS,FUSION

SA0474-01

HARN,JMPR,M-CREJ,EVO

SA0477-01

15.00TS&DSPL,VID MDL,EVO

(NO DISCOUNT)

SA0480-01

SM PRZ ASSY,U3a

SA0481-01

MED PRZ ASSY,U3a

SA0482-01

LG PRZ ASSY,U3a

SA0483-01

PRZ DSPL ASSY,U3a

SA0484-01

PRZ SHIELD (TOWER) ASSEMBLY,U3a

SA0485-01

MED PRZ HOPPER,U3a

SA0486-01

BENT PLASTIC PARTS,U3a

SA0487-01

VACUMED FORMED PARTS,U3a

SA0503-02

FLATSCREEN PRIMARY AC CABLE ASSEMBLY, FUSION

SA0505-01

TOUCHSCREEN POWER CABLE, FUSION

SA0506-01

LCD POWER CABLE, FUSION

SA0507-01

MECHANICAL COIN REJECTOR CABLE, FUSION

SA0519-01

65"L LED HARNESS, VIPS

SA10051-01

I/O BOARD W/ PRINTER

SA10055-01

USB I/O BOARD, W/O PRINTER

SA10057-05

533MHZ FORCE MOTHERBOARD ASSEMBLY

SA10057-07

810E,566MHz FORCE MOTHERBOARD ASSEMBLY

SA10058-01

AUDIO AMP BOARD

SA10062-01

ELECTRO-LUMINESCENT DRIVER BOARD, VIBE

SA10064-02

CTRL BOARD, JUKEBOX

SA10065-01

3-IN-1 I/O BOARD

SA10066-01

OSD SMART PANEL

SA10067-02

CC, LED BD,EVO

Cabinet Information - General Information - Megatouch FORCE Parts List

Megatouch FORCE Technical Reference Manual

Megatouch FORCE Parts List continued

Item

Description

SA3220-12-0A

.25 / .25 COIN DOOR ASSEMBLY

SA3235-12

.25/$1&$5B/A, 500 STACKER

SA3243-03

BEZEL, UPRIGHT (W/O COIN DOOR)

SA3244-03

19" CRT MONITOR ASSEMBLY

SA3248-01

COINBOX ASSEMBLY

SA3273-01

BEZEL ASSEMBLY

SA3276-01

FR BZL, JUKEBOX

SA3277-01

MONITOR MODULE, JUKEBOX

SA3278-01

LOWER FRONT PANEL ASSEMBLY, JUKEBOX

SA4084

4" SPEAKER ASSEMBLY W/ 2-PIN CONNECTOR

SA5117-04-0A

FAN ASSEMBLY, 3", 12V, 2 PIN CONNECTOR, W/O GUARD

SA5117-05-0A

FAN ASSEMBLY, 3", 12VDC, 3 PIN, W/ GUARD

SA5117-08

FAN ASSEMBLY, 3", 12V, M&F CONNECTOR, W/ GUARD

SA5117-09

3" 12V FAN ASSEMBLY W/ 2-PIN CONNECTOR & GUARD

SA5129-01

GASKET/BEZEL ASSEMBLY, 13"

SA7297-13

MAG SIGN HOLDER

SA9824-01

13" TOUCHSCREEN OVERLAY

SB0016-01

13"/19" TOUCHSCREEN TAPE KIT

SB0350-01

ELECTRONIC COIN REJECTOR-READY

SB0353-01

RADION SIGN MOUNTING KIT

SB0368-01

COIN BAG ASSEMBLY, VIBE W/ COIN

SB0377-01

US,25¢/$1,V92 COIN REJECTOR

(HW8337-01)

SB1771-05

GROUND, W/#4 & #6 RING LUGS 5"

SC7000

VARISTOR V130LA2OB

SC7005

VARISTOR 230VAC

SW3005

PANEL MOUNTING SWITCH, PB MOMENTARY

SW4024

ROCKER SWITCH, DPST, 250V, PANEL MOUNTING

SW4025-01

IEC, 250V, DPST, PANEL MOUNTING ROCKER SWITCH

SW5021-01

COIN SWITCH ASSEMBLY

WD0001-05

RIGHT SIDE PANEL

WD0001-06

LEFT SIDE PANEL

WD0013-01

CRT SHELF

WD0022-01

WOOD SHIM

WD0024-02

BLACK CABINET (discontinued under run out)

WD0024-03

DARK GRAY CABINET

WD0025-01

DARK GRAY CABINET

WD0030-01

SIDE PANEL

WD0030-02

SIDE PANEL

WD0038-01

MON SLF, JUKEBOX

WD0040-01

ENCLOSURE, JUKEBOX

WD0041-01

SOUND SYSTEM ENCLOSURE, SS

WD0047-01

FUSION CABINET

WD0054-01

FUSION CABINET

FORCE Hard Drive Program Numbers, Part Numbers, and

Compatible Security Keys

Hard drive program versions are in parentheses.
All security key program numbers are USA standard.

Hard Drive Information - Hard Drive Numbers

Megatouch FORCE Technical Reference Manual

FORCE 2005.5

Program #PG3002
(V15.00)

Part #PA3021-02

Security Key #SA3083-01

FORCE 2005

Program # PG3002
(V14.00)

Part # PA3018-02

Security Key # SA3083-01

FORCE 2004 POINT 5

Program # PG3002
(V13.00, V13.01, V13.02, V13.10)

Part # PA3017-02

Security Key # SA3068-01

FORCE 2004

Program # PG3002
(V12.00, V12.01, V12.02, V12.03,
V12.10, V12.11)

Part # PA3016-02

Security Key # SA3068-01

FORCE 2003 POINT 5

Program # PG3002
(V11.00, V11.01, V11.02, V11.05)

Part # PA3014-02

Security Key # SA3059-01

FORCE 2003

Program # PG3002
(V10.00, V10.02, V10.03, V10.06,
V10.07, V10.08, V10.09, V10.10)

Part # PA3013-02

Security Key # SA3059-01

FORCE 2002 POINT 5

Program # PG3002
(V9.00, V9.01)

Part # PA3012-02

Security Key # SA3050-01

FORCE 2002

Program # PG3002
(V8.00, V8.01, V8.02, V8.03,
V8.04, V8.05, V8.06)

Part # PA3010-01

Security Key # SA3050-01

MR VIPS

Program # PG4000
(V1.09, V2.01, V3.00, V3.01)

Part # SA0331-03

Security Key # SA3073-01

Troubleshooting Information - Troubleshooting Your Touchscreen

Megatouch FORCE Technical Reference Manual

MICROTOUCH:

Features:
- SMT-4 Controller in black box
- Green LED on controller lit at half brightness, full brightness when screen is touched
- Overlay functions on capacitance.
- Touchscreen cable is on right side of CRT.

Troubleshooting:
- LED Flashing from 1 to 5 times - detected error or possible defective controller
- LED not lit - Check +12 vdc. The SMT-3 controller may also be defective

See Figure 1 for the touchscreen overlay connector schematic.

CALIBRATION:

1 - Press the calibration button.
2 - Touch the dot that appears in the corner for 2 seconds.
3 - Touch the dot that appears in the opposite corner for 2 seconds.

The cursor should follow your finger wherever you touch the screen.

CALIBRATION or LOCKUP PROBLEMS:

•

If the calibration is off over the whole area of the screen, recalibrate the screen. If this does not
correct the problem, replace the touchscreen.

•

If the calibration is off in one area, check for scratches or nicks on the screen. If you detect
scratches or nicks, replace the touchscreen.

•

If the screen loses calibration entirely, check the ground pin on the line cord.

•

Microwave ovens and neon lights can and will interfere with the calibration of the touchscreen and
should not be within 6 feet (or 2 meters) of the game.

•

Improper grounding will affect the operation of the touchscreen.

•

If you are experiencing problems with double-touching (e.g. two cards are taken away after only
one touch to the screen), make sure the A/C plug and wall outlets are properly grounded.

•

The touchscreen cable should not positioned under or on top of the yoke of the monitor.

•

The touchscreen controller cable should not positioned near the flyback transformer.

NOTE: If the cable was incorrectly installed, the touchscreen response will be out of sync by
180 degrees.

Troubleshooting Your Touchscreen

Troubleshooting Information - Touchscreen Calibration

Megatouch FORCE Technical Reference Manual

Touchscreen Calibration

1. Find the

CALIBRATE

button on the I/O board and press it to enter the screen calibration

mode.

2. Touch the center of the first circle that appears on the screen. Once you release your finger,

a second circle will appear.

NOTE: You must hold your finger on the circle for approximately 2 seconds for the calibration
to be recognized.

3. Touch the center of the second circle that appears on the screen.

Pre-FORCE 2003 games only:

A third circle will appear to calibrate for low color games.

Touch the center of the third circle.

Pre-FORCE 2003 games only:

Once the third circle is touched and released, a crosshair will

appear on the screen. To test the calibration of the screen, touch the crosshair with your finger
and slowly drag your finger around the screen. The crosshair should follow your movement.

6. Move the cursor to ensure proper calibration.

7. Touch the

EXIT

button.

NOTE: If you perform a touchscreen test through set-up mode on a Pre-FORCE 2003 game, a
“LOW COLOR ADJUSTMENT” button will appear in the upper left corner of the screen to give
you the option to set the low color adjustment.

NOTE: If you have enabled high resolution, the game will prompt you to go through the cali-
bration procedure twice.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Classic Countertop

Hard Drive Removal

1. Turn off and unplug the game.

2. Unlock and open the lid.

3. Remove the screw securing the hard drive mounting plate to the game. See Figure 1.

4. Remove the 4 screws and shoulder washers securing the hard drive to the mounting plate.

5. Disconnect the 4-PIN power connector and the ribbon cable from the hard drive, then remove

the hard drive assembly from the game.

Hard Drive Installation

1. Connect the 4-PIN power connector and the ribbon cable to the new hard drive.

2. Place the new hard drive in the mounting plate and replace the 4 screws and shoulder washers

securing the drive to the plate.

3. Fasten the hard drive mounting plate to the game with the mounting screw. See Figure 1.

4. Close and lock the lid.

5. Plug in and turn on the game.

Motherboard Removal

1. Turn off and unplug the game.

2. Unlock and open the lid.

3. Disconnect all connections to the motherboard, including the ground wire attached to the

motherboard mounting frame.

4. Remove the 4 screws mounting the motherboard to the mounting frame (see Figure 2) and

carefully remove the board. Insert the board into an anti-static bag for storage. NOTE: Be sure
to read the Motherboard Handling Precautions before handling the board.

Motherboard Installation

1. Place the new motherboard on the mounting frame, lining up the screw holes on the board with

the holes in the game, then replace the 4 screws.

2. Reconnect all connections to the motherboard, including the ground wire attached to the

motherboard mounting frame.

3. Close and lock the lid.

4. Plug in and turn on the game.

Monitor Removal

1. Turn off and unplug the game.

2. Unlock and remove the coin box or coin box/bill acceptor assembly.

3. Unlock and remove the lid by first disconnecting the fan power connector, then the clear drain-

age tubing (from lid end) and ground strap. Also remove the monitor control board attached
with velcro to the inside of the game. Then press up on the spring-loaded levers (located on
each side of the lid), push the levers forward, and lift and remove the lid. Also remove the front
bezel. See Figures 3 and 4.

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Classic Countertop

Megatouch FORCE Technical Reference Manual

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Classic Countertop

Megatouch FORCE Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Classic Countertop (cont’d)

4. Disconnect the ground wire (with the ring lug) that is attached to the metalwork next to the

touchscreen controller. Then disconnect the cable from the back of the controller and discon-
nect the Molex connector connecting the orange and gray wires (from the touchscreen control-
ler cable) to the main harness.

5. Disconnect the monitor power connector (black and white wires running from the monitor board

to the right angle connector plugged into the power supply).

6. Disconnect the monitor signal cable from the motherboard.

7. Remove the 4 nuts securing the monitor chassis to the main chassis. Two nuts are located on

each side of the monitor board. See Figure 5 for locations. NOTE: BE CAREFUL TO AVOID
THE FLYBACK TRANSFORMER AND HIGH VOLTAGE WIRE RUNNING TO THE MONITOR.

8. Pick up the monitor assembly and remove it from the cabinet.

Monitor Installation

1. Place the new monitor assembly in the cabinet.

2. Fasten the monitor chassis to the main chassis with the 4 nuts, 2 on each side of the monitor

board. NOTE: BE CAREFUL TO AVOID THE FLYBACK TRANSFORMER AND HIGH VOLTAGE
WIRE RUNNING TO THE MONITOR.

3. Connect the monitor signal cable to the motherboard.

4. Reconnect the monitor power connector to the monitor board.

5. Reconnect the touchscreen cable in the back of the controller, then reconnect the Molex

connector to the main harness.

6. After replacing the front bezel, install the hood on the chassis, connecting the fan power

connector, monitor control board, ground strap, and plastic drain tube. Then pull the lid towards
you until the spring-loaded levers lock into place. See Figures 3 and 4.

7. Close and lock the lid.

8. Replace and lock the coin box or coin box/bill acceptor assembly.

9. Plug in and turn on the game.

Touchscreen Removal

1. Turn off and unplug the game.

2. Unlock and remove the coin box or coin box/bill acceptor assembly.

3. Unlock and remove the lid by first disconnecting the fan power connector, then the clear drain-

4. Remove the two nuts and washers securing the touchscreen controller to the game and re-

move the controller from the mounting screws. Then disconnect the touchscreen controller
cable from the back of the controller and disconnect the Molex connector (orange and gray
wires) running from the touchscreen controller cable to the main power harness.

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Classic Countertop

Megatouch FORCE Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Classic Countertop (cont’d)

5. Remove the black poly tape from around the edges of the old touchscreen. Remember how

the tape was placed in order to tape the new touchscreen.

6. Use dental floss to carefully cut the foam tape holding the touchscreen to the picture tube until

you are able to completely remove the touchscreen.

7. Remove any remaining adhesive residue with denatured alcohol, then wipe the surface of the

picture tube with the supplied alcohol wipe.

Touchscreen Installation

1. Clean the reverse side of the replacement touchscreen with the supplied alcohol wipe.

2. If there is no tape already on the screen, cut pieces of the supplied 1/2” double-sided foam tape

long enough to cover each edge of the screen without overlapping. After the tape is in place on
the screen, peel off the backing.

3. Replace the new touchscreen over the picture tube (with the cable on the right if you are facing

the game), making sure the screen is properly and evenly aligned over the picture tube. Then
clean the front of the screen with the supplied alcohol wipe.

4. Remembering the manner in which the tape was placed around the touchscreen you removed,

place and cut a length of the supplied black poly tape evenly over an entire edge of the touch-
screen and repeat until all 4 edges are covered.

5. Place and cut a longer length of black poly tape around all 4 edges of the screen.

6. Route the new touchscreen controller cable under the picture tube and away from the flyback

transformer. Then reconnect the cable in the back of the controller and secure the controller on
the mounting screws in the game with the existing hardware. Also connect the Molex connec-
tor (orange and gray wires) to the main power harness.

NOTE: Use the supplied roll of 3/8” foam tape (the thicker of the two 3/8” rolls) if you need to
replace the gasket on the inside of the front bezel. Be sure to remove all of the existing foam
tape and adhesive first.

7. After replacing the front bezel, install the lid on the chassis, connecting the fan power connec-

tor, monitor control board, ground strap, and plastic drain tube. Then pull the lid towards you
until the spring-loaded levers lock into place. See Figures 3 and 4 for locations.

8. Close and lock the lid.

9. Plug in and turn on the game.

10. When the game is finshed booting, calibrate the touchscreen.

11. Replace and lock the coin box or coin box/bill acceptor assembly.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Elite Countertop

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Elite Countertop

Megatouch FORCE Technical Reference Manual

Motherboard Removal

1. Turn off and unplug the game.

2. Unlock and open the rear door.

3. Disconnect all connections to the motherboard.

4. Remove the 4 screws mounting the motherboard to the mounting frame (see Figure 1) and

carefully remove the board. Insert the board into an anti-static bag for storage. NOTE: Be

sure to read the Motherboard Handling Precautions before handling the board.

Motherboard Installation

1. Place the new motherboard on the mounting frame, lining up the screw holes on the board

with the holes in the game, then replace the 4 screws.

2. Reconnect all connections to themotherboard.

3. Close and lock the rear door.

4. Plug in and turn on the game.

Hard Drive Removal

1. Turn off and unplug the game.

2. Unlock and open the rear door.

3. Remove the screw securing the hard drive mounting plate (see Figure 2) and slide the hard

drive assembly towards the back of the unit.

4. Remove the 4 screws and shoulder washers fastening the hard drive to the mounting plate.

5. Lift the hard drive out of the game until you’re able to disconnect the 4-pin power connector and

the hard drive ribbon cable from the rear of the hard drive.

Hard Drive Installation

1. Connect the power connector and the ribbon cable to the hard drive.

2. Fasten the hard drive to the mounting plate with the 4 screws and shoulder washers.

3. Slide the hard drive assembly into the game and fasten it with the mounting screw.

4. Close and lock the rear door.

5. Plug in and turn on the game.

Monitor Removal

1. Turn off and unplug the game.

2. Unlock and open the rear door.

3. Disconnect the monitor power connection (black and yellow wires) running to the power sup-

ply.

4. Disconnect the monitor signal cable from the motherboard and remove it from the cable clamps.

5. Inside the game, access the latches for each side panel and remove both panels (see Figure

3).

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Elite Countertop (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Elite Countertop

Megatouch FORCE Technical Reference Manual

6. Remove the two nuts and washers securing the touchscreen controller to the game and re-

move the controller from the mounting screws. Then disconnect the cable from the back of the
controller and disconnect the Molex connector connecting the orange and gray wires (from the
touchscreen controller cable) to the main power harness.

7. Remove the 3 screws at the top of each side piece fastening the top cover to the game (see

Figure 4) and remove the top cover.

8. Loosen the 5/16” nuts securing the 2 LCD clips (one on each side piece). See Figure 4.

9. Lift the bezel and monitor assembly from the game.

Monitor Installation

1. Place the new bezel and monitor assembly in the game.

2. Tighten the nuts securing the LCD clips on each side piece. See Figure 4.

3. Replace the top cover and the 3 screws at the top of each side piece. See Figure 4.

4. Connect the touchscreen cable in the back of the touchscreen connector and the touchscreen

power connector to the main power harness. The replace the connector on the mounting
screws in the game and secure it with the two nuts.

5. Replace both side panels (see Figure 3).

6. Replace the monitor signal cable in the cable clamps and reconnect it to the motherboard.

7. Connect the power connector on the new monitor to the connector running to the power supply.

8. Close and lock the rear door.

9. Plug in and turn on the game.

10. Calibrate the touchscreen.

Touchscreen Removal

1. Turn off and unplug the game.

2. Unlock and open the rear door.

3. Disconnect the monitor power connection (black and yellow wires) running to the power sup-

ply.

4. Disconnect the monitor signal cable from the motherboard and remove it from the cable clamps.

5. Inside the game, access the latches for each side panel and remove both panels (see Figure

3).

6. Remove the two nuts and washers securing the touchscreen controller to the game and re-

move the controller from the mounting screws. Then disconnect the cable from the back of the
controller and disconnect the Molex connector (orange and gray wires) running from the
touchscreen controller cable to the main power harness.

7. Remove the 3 screws at the top of each side piece fastening the top cover to the game (see

Figure 4) and remove the top cover.

8. Loosen the 5/16” nuts securing the 2 LCD clips (one on each side piece). See Figure 4.

9. Lift the bezel and monitor assembly from the game.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Elite Countertop (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Elite Countertop

Megatouch FORCE Technical Reference Manual

10. Remove the 3 screws on top of the front bezel (see Figure 4) and separate the bezel from the

monitor.

11. Use dental floss to carefully cut the foam tape holding the touchscreen to the monitor until you

are able to completely remove the touchscreen.

12. Remove any remaining adhesive residue with denatured alcohol, then clean the monitor glass

with the supplied alcohol wipe.

Touchscreen Installation

1. Clean the reverse side of the replacement touchscreen with the supplied alcohol wipe.

2. Cut pieces of the supplied 1/2” double-sided foam tape long enough to cover each edge of the

screen without overlapping. After the tape is in place on the screen, peel off the backing.

3. Replace the new touchscreen over the monitor (with the cable on the left if you are facing the

game), making sure the screen is properly and evenly aligned over the monitor glass. Then
clean the front of the screen with the supplied alcohol wipe.

4. Reattach the front bezel to the monitor with the 3 screws removed earlier. See Figure 4.

5. Replace the monitor assembly, aligning it with the support brackets inside the game and mak-

ing sure the LCD clips fit properly into the slots at the top of each side.

6. Tighten the nuts securing the 2 LCD clips. See Figure 4.

7. Replace the top cover.

8. Replace the 3 screws at the top of each side piece. The shorter screw will go in the screw hole

closest to the rear of the game. See Figure 4.

9. Connect the new touchscreen controller cable in the back of the controller and secure the

controller on the mounting screws in the game with the existing hardware. Also connect the
Molex connector (orange and gray wires) to the main power harness.

10. Replace both side panels.

11. Reconnect the monitor power connector to the power supply.

12. Route the monitor signal connector through the cable clamps and reconnect it to the

motherboard.

13. Plug in and turn on the game.

14. When the game is finshed booting, calibrate the touchscreen.

15. Close and lock the rear door.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Radion Countertop/Fun Zone JR.

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Radion Countertop /Fun Zone JR games

Megatouch FORCE Technical Reference Manual

Motherboard Removal

1. Turn off and unplug the game.

2. Unlock and open/remove the rear door and the side doors.

3. Disconnect all connections to the motherboard, as well as the touchscreen and centronics

power connectors from the power supply harness.

4. Remove the 4 screws mounting the motherboard to the mounting frame (see Figure 1) and

carefully remove the board. Insert the board into an anti-static bag for storage. NOTE: Be
sure to read the Motherboard Handling Precautions before handling the board.

Motherboard Installation

1. Place the new motherboard on the mounting frame, lining up the screw holes on the board

with the holes in the game, then replace the 4 screws.

2. Reconnect all connections to the motherboard, as well as the touchscreen and centronics

power connectors from the power supply harness.

3. Close/replace and lock the rear door and the side doors.

4. Plug in and turn on the game.

Hard Drive Removal

1. Turn off and unplug the game.

2. Unlock and open/remove the side doors and the rear door.

3. Locate the hard drive and remove the 2 screws securing the hard drive mounting bracket to

the game (see Figure 2), then remove the hard drive assembly until you’re able to disconnect
the hard drive power connector and the motherboard ribbon cable.

4. Remove the 4 screws and shoulder washers fastening the hard drive to the mounting plate.

Hard Drive Installation

1. Fasten the new hard drive to the mounting plate with the 4 screws and shoulder washers.

2. Connect the power connector and the hard drive ribbon cable to the hard drive, then replace

the hard drive assembly in the game and fasten it with the 2 screws.

3. Close/replace and lock the rear door and the side doors.

4. Plug in and turn on the game.

Monitor Removal

1. Turn off and unplug the game.

2. Unlock and open/remove the side doors and the rear door.

3. Remove the screw securing the strain relief cord to the rear door, then remove the monitor

control board from the velcro on the rear door.

4. Remove the screws holding the rear bezel to the game and remove the bezel. Five screws

fasten the top edge of the bezel and 2 on each side fasten the bottom. See Figure 3.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Radion Countertop/Fun Zone JR. (cont’d)

Troubleshooting Information - Installation of Major Assemblies -

FORCE Radion Countertop/Fun Zone JR.

Megatouch FORCE Technical Reference Manual

5. Remove the 4 screws holding the front bezel to the game and remove the bezel. Two screws

fasten the top of the bezel and 1 screw on each side fastens the bottom. See Figures 3 and 4.

6. Disconnect all connections to the motherboard, as well as the touchscreen and centronics

power connectors from the power supply harness.

7. Unscrew the 2 thumbscrews securing the motherboard mounting tray to the game and remove

the motherboard and mounting tray. NOTE: Be sure to read the Motherboard Handling Pre-
cautions before handling the board.

8. Locate the hard drive and remove the 2 screws securing the hard drive mounting bracket to the

game (see Figure 2), then remove the hard drive assembly until you’re able to disconnect the
hard drive power connector.

9. Unscrew the thumbscrew securing the fan assembly, disconnect the 2-pin fan power connec-

tor, and remove the fan assembly from the game. See Figure 2.

10. Unscrew the 2 thumbscrews securing the touchscreen controller mounting plate and remove

the touchscreen controller assembly. After removing the two thumbnuts securing the touch-
screen controller to the mounting plate, disconnect the cable from the back of the controller and
disconnect the Molex connector connecting the orange and gray wires (from the touchscreen
controller cable) to the main power harness.

11. Remove the 2 cable clamps fastening the power harnesses to the game.

12. Disconnect the power supply line cord, then unscrew the thumbnut securing the power supply

to the game. After disconnecting the second fan power connector and the power supply con-
nector from the I/O board, remove the power supply from the game. NOTE: Be sure to note
the orientation of the wiring when disconnecting the fan power connector.

13. Pull out the coin rejector (see Figure 5) and remove the single fan assembly (attached to the

game chassis with 1 thumbnut).

14. Remove the coin rejector chute (secured with 4 nuts and washers) and the coin chute (se-

cured with 2 nuts). See Figure 5. NOTE: You may need to move the speaker assembly aside
to access the nuts securing the coin chute.

15. Remove the 2 screws fastening the optical coin sensor (see Figure 5) to the game.

16. Remove the 2 nuts fastening the monitor assembly to the metalwork inside the game. You will

also need to remove the cable clamp secured by one of the nuts.

17. Remove the nut and screw securing the strain relief cord to the inside of the game.

18. Remove the 2 screws fastening the coin harness connector (see Figure 5) to the monitor

assembly.

19. Disconnect the line cord from the monitor assembly, then disconnect the ground wire and

monitor signal cable from the mounting standoff on the game chassis.

20. Remove the 3 screws fastening each side of the monitor assembly to the game chassis (one

screw will also be securing a cable clamp and another will be securing the angled bracket on
the edge of the monitor chassis board). Then carefully remove the monitor assembly from the
game.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Radion Countertop/Fun Zone JR. (cont’d)

Troubleshooting Information - Installation of Major Assemblies -

FORCE Radion Countertop/Fun Zone JR.

Megatouch FORCE Technical Reference Manual

Monitor Installation

1. Replace the monitor assembly in the game and fasten it to the chassis with the 3 screws (also

fasten the cable clamp and angled bracket with the appropriate screw).

2. Replace the ground wire and monitor signal cable on the mounting standoff on the game chas-

sis, then connect the line cord to the monitor assembly.

3. Fasten the coin harness connector to the monitor assembly with the 2 screws (see Figure 5).

4. Fasten the strain relief cord to the inside of the game with the nut and screw.

5. Fasten the monitor assembly to the metalwork inside the game with the 2 nuts. One of the nuts

will also secure the cable clamp.

6. Fasten the optical coin sensor (see Figure 5) to the game with the 2 screws.

7. Replace the coin rejector chute and secure it with the 4 nuts and washers, then secure the coin

chute with the 2 nuts. See Figure 5. Also replace the speaker assembly if you moved it in order
to access the nuts securing the coin chute.

8. Replace the single fan assembly and fasten it to the game chassis with the thumbnut, then

replace the coin rejector (see Figure 5).

9. Replace the power supply in the game and secure it with the thumbnut, then reconnect the

power supply line cord. Also reconnect the power supply connector and fan power connector
to the I/O board.

10. Replace the 2 cable clamps and refasten the power harness to the game.

11. Connect the touchscreen cable in the back of the touchscreen controller and also reconnect

the touchscreen power connector to the main power harness. After securing the controller on
the mounting plate with the 2 thumbnuts, replace the touchscreen controller assembly in the
game and fasten the mounting plate with the 2 thumbscrews.

12. Replace the fan assembly in the game and reconnect the fan power connector, then tighten the

thumbscrew securing the fan assembly. See Figure 2.

13. Reconnect the hard drive power connector to the hard drive, then replace the hard drive in the

game and secure it with the 2 screws (see Figure 2).

14. Replace the motherboard and mounting tray in the game and secure the tray with the 2 thumb-

screws.

15. Reconnect the touchscreen and centronics power connectors to the power supply harness,

then reconnect all connections to the motherboard.

16. Replace the front bezel and fasten it to the game with the 4 screws. Two screws will fasten the

top of the bezel and 1 screw on each side will fasten the bottom. See Figures 3 and 4.

17. Replace the rear bezel and fasten it to the game with the 7 screws. Five screws will fasten the

top edge of the bezel and 2 on each side will fasten the bottom. See Figure 3.

18. Replace the monitor control board on the velcro on the rear door, then replace the screw secur-

ing the strain relief cord to the rear door.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Radion Countertop/Fun Zone JR. (cont’d)

Troubleshooting Information - Installation of Major Assemblies -

FORCE Radion Countertop/Fun Zone JR.

Megatouch FORCE Technical Reference Manual

19. Close/replace and lock the rear door and the side doors.

20. Plug in and turn on the game.

21. Calibrate the touchscreen.

Touchscreen Removal

1. Turn off and unplug the game.

2. Unlock and open/remove the rear door and the side doors.

3. Remove the cash box.

4. Remove the screw securing the strain relief cord to the rear door, then remove the monitor

board from the velcro on the rear door.

5. Remove the screws holding the rear bezel to the game. Five screws are located along the top

edge of the game and 2 are at the bottom rear of each side of the game. See Figure 3.

6. Lift the rear bezel from the game.

7. Remove the 4 screws holding the front bezel to the game. Two screws are located at the

bottom on each side of the game (see Figure 3) and 2 are on the top surface (see Figure 4).

8. Lift the front bezel from the game.

9. Remove the two nuts and washers securing the touchscreen controller (see Figure 6) to the

game and remove the controller from the mounting screws. Then disconnect the cable from
the back of the controller and disconnect the Molex connector (orange and gray wires) running
from the touchscreen controller cable to the main power harness.

10. Remove the black poly tape from around the edges of the old touchscreen. Remember how

the tape was placed in order to tape the new touchscreen.

11. Use dental floss to carefully cut the foam tape holding the touchscreen to the picture tube until

you are able to completely remove the touchscreen.

12. Remove any remaining adhesive residue with denatured alcohol, then wipe the surface of the

picture tube with the supplied alcohol wipe.

Touchscreen Installation

1. Clean the reverse side of the replacement touchscreen with the supplied alcohol wipe.

2. Peel the backing from the 8 pieces of foam tape already adhered to the reverse side of the

touchscreen. Then cut 8 pieces of equal size from the supplied roll of 3/8” double-sided foam
tape (the thinner of the two supplied 3/8” rolls) and place them (backing side facing out) on the
tape already on the touchscreen before peeling off the backing. The double-thickness of the
foam tape will allow enough distance between the touchscreen and the picture tube once the
new screen is in place.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Radion Countertop/Fun Zone JR. (cont’d)

Troubleshooting Information - Installation of Major Assemblies -

FORCE Radion Countertop/Fun Zone JR.

Megatouch FORCE Technical Reference Manual

3. Replace the new touchscreen over the picture tube (with the cable on the left if you are facing

the game), making sure the screen is properly and evenly aligned over the picture tube. Then
clean the front of the screen with the supplied alcohol wipe.

4. Connect the new touchscreen controller cable in the back of the controller and secure the

controller on the mounting screws in the game with the existing hardware (see Figure 6). Also
connect the Molex connector (orange and gray wires) to the main power harness.

5. Remembering the manner in which the tape was placed around the touchscreen you removed,

place and cut a length of the supplied black poly tape evenly over an entire edge of the touch-
screen and repeat until all 4 edges are covered.

6. Place and cut a longer length of black poly tape around all 4 edges of the screen. NOTE: Use

the additional 3/8” foam tape (the thicker of the two supplied 3/8” rolls) if you need to replace the
gasket on the inside of the front bezel. Be sure to remove all of the existing foam tape and
adhesive first.

7. Replace the front bezel and the 4 screws (2 at the bottom, 2 at the top) holding the bezel to the

game. See Figures 3 and 4.

8. Replace the rear bezel and the 7 screws (5 along the top edge, 2 at the bottom rear) holding the

bezel to the game. See Figure 3.

9. Replace the screw securing the strain relief cord to the rear door, then replace the monitor

board.

10. Replace the cash box.

11. Plug in and turn on the game.

12. When the game is finshed booting, calibrate the touchscreen.

13. Close/replace and lock the rear door and the side doors.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Radion Countertop/Fun Zone JR. (cont’d)

Troubleshooting Information - Installation of Major Assemblies -

FORCE Radion Countertop/Fun Zone JR.

Megatouch FORCE Technical Reference Manual

Power Supply Removal

1. Turn off and unplug the game.

2. Unlock and open the rear door.

3. Remove the screw securing the strain relief cord to the rear door, if necessary.

4. If applicable, loosen the captive screw securing the modem assembly to the game (see Figure

7), and remove the modem assembly from the game.

5. Loosen the captive screw securing the power supply assembly to the game (see Figure 8). (If

necessary, free the cables from the cable clamp on the motherboard; these cables may be
blocking the power supply. See Figure 7.) Unplug the power cord from the power supply and
remove the power supply from the game as much as possible. Disconnect the 10-pin connec-
tor harness from the back of the power supply and remove the assembly from the game com-
pletely. See Figure 8.

6. Remove the 4 screws securing the power supply to the power supply mounting bracket (3 are

located near the power inlet and 1 is near the 10-pin harness. See Figure 9. Separate the power
supply from its mounting bracket, and set this power supply aside.

Power Supply Installation

1. Place the new power supply in the power supply mounting bracket in the same manner as the

old power supply. Secure the supply to the mounting bracket with the same 4 screws. See
Figure 9.

2. Connect the 10-pin connector harness from the new power supply to its mating connector. See

Figure 8. Insert the power supply assembly in the game, making sure that the tabs on the
bottom of the bracket fit securely into their mating slots (you may have to press on the bracket
until it snaps into place). Secure the power supply assembly to the game by tightening the
captive screw. Plug the power cord into the power inlet on the new power supply. See Figure 8.

3. Replace the cables in the clamp on the motherboard (if applicable). See Figure 7. If applicable,

replace the modem assembly in the game, making sure that the 2 tabs on the bracket fit
securely in their mating slots. Secure by tightening the captive screw. See Figure 7.

4. Replace the screw securing the strain relief cord to the rear door, if applicable.

5. Close and lock the rear door.

6. Plug in and turn on the game.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge

Megatouch FORCE Technical Reference Manual

Motherboard Removal

1. Turn off and unplug the game.

2. Unlock and open the CPU section.

3. Remove the 2 screws securing the motherboard assembly to the game (see Figure 1).

4. Carefully pull the motherboard assembly away from the 2 brackets holding it in place on the

opposite side of the screws you removed (see Figure 2). NOTE: It may be necessary to
disconnect some of the connections to the board in order to pull the motherboard away from
the brackets.

5. Disconnect all connections to the motherboard, as well as the touchscreen and centronics

power connectors from the power supply harness. Then carefully remove the motherboard
assembly and insert the board into an anti-static bag for storage. NOTE: Be sure to read the
Motherboard Handling Precautions before handling the board.

Motherboard Installation

1. Reconnect the touchscreen and centronics power connectors to the power supply harness

and reconnect all connections to the motherboard.

2. Place the motherboard assembly behind the two brackets, line up the screw holes, and replace

the 2 mounting screws.

3. Close and lock the CPU section.

4. Plug in and turn on the game.

Hard Drive Removal

1. Turn off and unplug the game.

2. Unlock and open the CPU section.

3. Remove the 3 screws securing the hard drive mounting bracket to the game, then remove the

hard drive assembly until you’re able to disconnect the hard drive power connector and the
hard drive ribbon cable running to the motherboard. See Figure 3.

4. Remove the 4 screws and shoulder washers fastening the hard drive to the mounting plate.

See Figure 3.

Hard Drive Installation

1. Fasten the new hard drive to the mounting plate with the 4 screws and shoulder washers. See

Figure 3.

2. Connect the power connector and the ribbon cable to the hard drive, then fasten the hard drive

assembly in the game with the 3 screws. See Figure 3.

3. Close and lock the CPU section.

4. Plug in and turn on the game.

Monitor Removal

1. Turn off and unplug the game.

2. Place something in front of the game to brace the bezel once the strain relief cord is undone,

then unlock and open the CPU section.

3. Remove the screw and washer fastening the strain relief cord, then remove the remaining 5

screws fastening the LCD mounting bracket to the game and remove the bracket. Refer to
Figure 4 for monitors with interior circuit boards and Figure 5 for monitors with exterior circuit
boards. The bracket will not be reused.

4. Carefully cut the tie wrap around the VGA monitor cable, the OSD cable, and the setup/cali-

brate harness. See Figures 4 and 5.

5. Remove the ground screw attached to the VGA monitor cable, then disconnect the cable from

the monitor and remove it from the cable clamp. Also disconnect the other end of the cable
from the motherboard. See Figure 6 for monitors with interior circuit boards and Figures 7 and
8 for monitors with exterior circuit boards. NOTE: Monitors with exterior circuit boards will
have the ground screw attached in one of two places. Be sure to refer to Figures 7 and 8.

6. Remove the OSD cable from the twist clamp and disconnect it from the OSD board. Then

remove the OSD board from the velcro attached to the hinge and set it aside. See Figures 4
and 5.

7. Disconnect the LCD power connector. See Figures 6 and 7.

8. Remove the touchscreen controller ground screw under the hard drive (see Figures 6 and 7),

then remove the touchscreen cable from the corrugated loom alongside the bezel.

9. Disconnect the touchscreen power connector (see Figures 6 and 7), then remove both the

touchscreen controller cable and the touchscreen power cable from the clamp in the game.

10. Remove the 2 screws fastening the touchscreen controller to the mounting plate over the hard

drive, then disconnect the cable from the back of the controller.

11. Loosen the 3 screws on the monitor side of the hinges in order to carefully raise the hinges and

allow room to remove the monitor. See Figures 6 and 7.

12. Slide the monitor out of the bezel.

13. If you will not be reusing the existing touchscreen, continue with installing the new monitor. If

you will be reusing the touchscreen, note the orientation of the screen (i.e., the positioning of
the ribbon cable and which side is the front) before removing it from the monitor. Then use
dental floss to carefully cut the foam tape holding the screen to the monitor. Once the
touchscreen is completely free from the monitor, remove any residual foam tape from the
screen with denatured alcohol and clean the glass with the supplied alcohol wipe.

Monitor Installation

1. If you will not be using the touchscreen from your original monitor, skip to step 3. If you will be

using the original touchscreen, clean the glass on the new LCD monitor with the supplied
alcohol wipe, then cut pieces of the supplied 1/2” foam tape long enough to cover each edge of
the monitor without overlapping. After the tape is in place on the monitor, peel off the backing.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge

Megatouch FORCE Technical Reference Manual

2. Carefully place the touchscreen over the monitor in the same manner it was attached to the

old monitor, making sure the screen is properly and evenly aligned over the glass. Clean the
front of the touchscreen with the supplied alcohol wipe once it is in place.

Monitors with interior circuit boards:

Carefully slide the new monitor into the bezel with the

white edge of the monitor closest to the hinges in the game. Make sure the monitor is properly
centered, then tighten the hinge screws.

Monitors with exterior circuit boards:

Carefully slide the new monitor into the bezel with the

A to D board on the left and the inverter board on the right (if you are facing the game--see
Figure 5). Make sure the monitor is properly centered, then tighten the hinge screws.

4. Install the supplied LCD mounting bracket and fasten it to the game with the 6 screws. One

screw (and washer) will fasten the strain relief cord. See Figures 4 and 5.

5. Connect the touchscreen cable in the back of the controller, then mount the controller on the

plate above the hard drive with the 2 screws.

6. Replace the touchscreen controller cable and the touchscreen power cable in the cable clamp,

then connect the touchscreen power connector. See Figures 6 and 7.

7. Replace the touchscreen controller cable in the corrugated loom alongside the bezel, then

replace the touchscreen controller ground screw under the hard drive. See Figures 6 and 7.

8. Connect the LCD power connector. See Figures 6 and 7.

9. Reattach the OSD board to the velcro on the hinge, then connect the new OSD cable to both

the OSD board and the monitor. Secure the cable in the twist clamp. See Figures 4 and 5.

10. Connect the new VGA cable to both the monitor and the motherboard, then secure the cable in

the clamp under the bottom left corner of the motherboard. Also replace the ground screw.
See Figures 6-8. NOTE: Monitors with exterior circuit boards will have the ground screw
attached in one of two places. Be sure to refer to Figures 7 and 8.

11. Tie wrap the VGA monitor cable, the OSD cable, and the setup/calibrate harness. See Figures

4 and 5.

12. Close and lock the CPU section.

13. Plug in and turn on the game.

Touchscreen Removal

1. Turn off and unplug the game.

2. Unlock and open the CPU section and place something under the front bezel to brace it when

the strain relief cord is disconnected.

3. Remove the two screws securing the touchscreen controller to the game, then disconnect the

cable from the back of the controller. Also disconnect the Molex connector (orange and gray
wires) running from the touchscreen controller cable to the main power harness.

4. Remove the 6 screws fastening the LCD mounting bracket to the game (one screw also fas-

tens the strain relief cord) and remove the bracket. See Figures 4 and 5.

5. Disconnect all connections to the LCD monitor until you’re able to slide the monitor out of the

game.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge

Megatouch FORCE Technical Reference Manual

6. Note the orientation of the touchscreen cable before removing the screen. Then use dental

floss to carefully cut the foam tape holding the touchscreen to the monitor until you are able to
completely remove the screen.

7. Remove any remaining adhesive residue with denatured alcohol, then clean the monitor glass

with the supplied alcohol wipe.

Touchscreen Installation

1. Clean the reverse side of the replacement touchscreen with the supplied alcohol wipe.

2. Cut pieces of the supplied 1/2” double-sided foam tape long enough to cover each edge of the

screen without overlapping. After the tape is in place on the screen, peel off the backing.

3. Replace the new touchscreen over the monitor in the same manner as the old screen, making

sure the screen is properly and evenly aligned over the monitor glass. Then clean the front of
the screen with the supplied alcohol wipe.

4. Slide the LCD monitor assembly back into the game and reconnect all cables to the monitor.

5. Replace the LCD mounting bracket in the game and fasten it with the 6 screws removed

earlier. Also refasten the strain relief cord.

6. Connect the new touchscreen controller cable in the back of the controller and secure the

controller in the game with the existing hardware. Also connect the Molex connector (orange
and gray wires) to the main power harness.

7. Close and lock the CPU section.

8. Plug in and turn on the game.

9. When the game is finished booting, calibrate the touchscreen.

Power Supply Removal

1. Turn off and unplug the game.

If your game is NOT an eVo skip to Step 5.

2. Unlock and open the cash tower section.

3. Disconnect the LED power connector behind the CPU section (see Figure 9) and carefully

route the wires back through the access hole below the motherboard (see Figure 1).

4. Close and lock the cash tower section.

5. Unlock and open the CPU section.

6. Unplug the IEC connector from the power supply (see Figure 1).

7. Disconnect the power connector from the hard drive (see Figure 3) and remove the wires from

the cable clamp.

8. Disconnect the touchscreen/fan power connector, then remove the harness from the cable

clamp and disconnect the power connector to the other fan.

9. Remove the 2 screws on the right side of the motherboard (see Figure 1) and carefully pull the

motherboard forward after sliding it out of the clips on the left side of the board.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge

Megatouch FORCE Technical Reference Manual

10. Disconnect the centronics power connector (black, yellow, and red wires--see Figure 10).

11. Disconnect the I/O board power connector (black, yellow, blue, and black wires--see Figure 11)

located at J6 on the I/O board.

12. Disconnect the power supply connector from the motherboard (see Figure 12).

13. Remove the standoff securing the twist clamp in the upper right corner of the game, then undo

and remove the clamp (see Figure 13).

14. Remove the wires (black and yellow) running to the LCD monitor power connector from the

cable clamp, then disconnect the connector (see Figure 10).

15. Remove the 2 screws fastening the power supply and mounting bracket to the game (see

Figure 13).

16. Remove the power supply.

Power Supply Installation

1. Install the new power supply and bracket in the game and fasten them with the 2 screws that

were used to fasten the old power supply and bracket (see Figure 13).

EVO ONLY:

Locate the LED power connector on the new power supply harness and route the

wires down toward the access hole (see step 3 above).

3. Replace the twist clamp around the larger set of wires that will run to the motherboard and I/O

board, then reinstall the standoff (see Figure 13).

4. Reconnect the centronics power and LCD monitor connectors (see Figure 10), then replace

the wires running to the monitor in the cable clamp.

5. Reconnect the I/O board and power supply connectors on the I/O board and motherboard

respectively (see Figures 11 and 12).

6. Replace the motherboard by sliding it into the clamps on the left side of the game and lining up

the two screw holes on the right side of the board with the two standoffs in the game. Then
replace the 2 screws that fasten the board to the game (see Figure 1). Make sure no wires are
pinched after the motherboard is in place.

7. Reconnect power to the upper fan (next to the power supply).

8. Reconnect the IEC connector to the power supply (see Figure 1).

9. Reconnect the power connectors to the lower fan and the touchscreen.

10. Reconnect the hard drive power connector (see Figure 3) and replace the wires in the clamp

on the top left side of the game, then fasten the clamp.

11.

EVO ONLY:

Route the LED power connector through the access hole below the motherboard

(see Figure 1).

12. Close and lock the CPU section. Make sure no wires interfere when the bezel is closed.

13.

EVO ONLY:

Unlock and open the cash tower section.

14.

EVO ONLY:

Reconnect the LED power connector in the appropriate location behind the CPU

section (see Figure 9).

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge

Megatouch FORCE Technical Reference Manual

15.

EVO ONLY:

Close and lock the cash tower.

Bill Acceptor Removal

NOTE: Do not follow these instructions for Elite Edge. Please see the Elite Edge
Instruction section.

1. Turn off and unplug the game.

2. Unlock and open the CPU section, then place something in front of the front bezel to keep the

touchscreen from being scratched when the cash tower section is opened.

3. In the CPU section, locate and disconnect the coin mech harness (blue and gray ribbon cable)

found near the lower edge of the motherboard (see Figure 14) and remove it from the cable
clamps. Also disconnect the counter harness on the left edge of the motherboard, opposite the
touchscreen controller (see Figure 14). Then pull both connectors back through the access
hole below the board (see Figure 1) and out of the game.

4. Close and lock the CPU section.

5. Unlock and open the cash access section.

6. Pull out the bill acceptor magazine.

EVO only

: Disconnect the bill acceptor power connectors, as well as the fan and LED board

connectors (see Figure 15).

EVO Wallette only

: Remove the 2 screws fastening the bill acceptor mounting clip to the

game and gently pull up on the bill acceptor so that you can access the two connectors on the
right side. Disconnect the 2 connectors and remove the bill acceptor and mounting clip from
the game. Then remove the other two screws fastening the clip to the bill acceptor. See Figure
16. Skip to “Bill Acceptor Installation”.

8. Remove the 6 screws fastening the bill acceptor mounting plate to the CPU section (see Figure

15). One screw also fastens the strain relief cord. Once the screws are removed, pull the
harnesses attached to the CPU section through the access hole in the bill acceptor mounting
plate so the CPU section can be pulled free of the bill acceptor. Disconnect the IEC power
connector from the CPU section, then place the CPU section down with the touchscreen side
facing up.

9. Remove the 4 screws on the reverse side of the mounting plate fastening the bill acceptor

bezel to the plate (see Figure 17). One screw also fastens the cable clamp.

10. Remove the 4 screws fastening the bill acceptor to the mounting plate (see Figure 17) and

remove the bill acceptor.

Bill Acceptor Installation

1. Remove the magazine from the new bill acceptor. If you are replacing the bill acceptor on

an EVO Wallette, skip to step 5.

2. Using Figure 18, insert the bill acceptor into the mounting plate, then fasten the bill acceptor to

the plate with the 4 screws.

3. Reattach the bill acceptor bezel to the mounting plate by replacing the 4 screws on the

reverse side of the plate (see Figure 17). Also replace the cable clamp.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge

Megatouch FORCE Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge

Megatouch FORCE Technical Reference Manual

4. Reconnect the IEC power connector on the CPU section, then route the harnesses from the

CPU section back through the access hole in the bill acceptor mounting plate. Use the 6
screws to reattach the plate to the CPU section (see Figure 15) and fasten the strain relief
cord.

5. Reconnect the bill acceptor power connectors, as well as the fan and LED board connectors

(see Figure 15).

EVO Wallette only

: Fasten the bill acceptor mounting clip to the new bill acceptor. Then

connect the bill acceptor power connectors and fasten the bill acceptor mounting clip to the
game. See Figure 16.

6. Replace the bill acceptor magazine.

7. Unlock and open the CPU section.

8. Feed the coin mech and counter harnesses back through the access holes in the bill acceptor

mounting plate and motherboard (see Figure 1).

9. Reconnect the counter harness in the connector below the lower clip securing the motherboard,

then reconnect coin mech harness after replacing it in the cable clamps. See Figure 14.

10. Close and lock the CPU section.

11. Close and lock the cash tower section.

EVO Wallette only

: Close and lock the cash door.

12. Plug in and turn on the game.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge (cont’d)

Bill Acceptor Removal - Elite Edge only

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge

Megatouch FORCE Technical Reference Manual

1. Turn off and unplug the game.

2. Unlock and open the cash door.

3. Disconnect the ground wire and remove the cash door.

4. Remove any money from the coin box, then remove the coin box and magazine stacker from the

game. See Figure 19.

5. Rest the game facedown to access the base. Protect and stablize the front casing and monitor by

prepping the area with cardboard, foam, etc.

6. Remove the circular anti-skid pad on the bottom of the game. Keep the anti-skid pad for use in

installation. See Figure 20.

7. Remove the (2) screws located at the bottom of the anti-skid circle. See Figure 20.

8. Remove the (12) screws outside the circle that are securing the bottom cover. See Figure 20.

NOTE: When removing the last few screws, be sure to hold the cover in place. If the cover is not
properly secured, it may cause injury to the operator and/or damage the cover.

9. Seperate the convertor from the Velcro strip on the game base, then completely remove the base.

10. Remove all harnesses from the bill acceptor.

11. Remove the (4) nuts and spacers securing the bill acceptor to the mounting plate.

13. Remove the power wire clip from the PEM stud.

14. Seperate the bill acceptor from the mounting plate.

12. Remove the (4) screws connecting the mounting plate to the game housing. Lift the mounting

plate out of the game. See Figure 21.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge

Megatouch FORCE Technical Reference Manual

Bill Acceptor Installation - Elite Edge only

1. Remove the magazine stacker from the new bill acceptor.

2. Reattach the (4) screws connecting the mounting plate to the housing of the game. See Figure

21.

3. Insert the bill acceptor into the mounting plate. Put power wire clip back on PEM stud, then fasten

the bill acceptor to the plate with the existing (4) nuts and spacers.

4. Reconnect all harnesses. Plug the harness with (3) wires into the back socket. Plug the harness

with (2) wires into the front socket. NOTE: The front is the socket closest to the monitor of the
game. The harnesses MUST be installed in the proper slots. Failure to do so will result in game
malfunction.

5. Slide the base cover into place for re-installation. When doing so, make sure the lights on the left

and right side of the game are securely in place. Also tuck in the wires on the bottom of the bill
acceptor. See Figure 21.

6. Reattach the converter to the Velcro strip on the base of the game.

7. Reattach the base using the (12) screws. NOTE: Keep the back cover securely in place as you

work. If the cover is not properly secured, it may cause injury to the operator and/or damage the
cover. See Figure 20.

8. Secure the anti-skid circle by replacing the (2) bottom screws. See Figure 20.

9. Reaffix the anti-skid pad to the circle. See Figure 20. If it will not adhere properly, apply glue to the

back of the pad or contact Merit to order a replacement.

10. Return the game to its proper upright position.

11. In the cash tower section, reinstall the coin box and the new bill acceptor magazine.

12. Reattach the cash door and ground wire, then close and lock the door.

$background image$

FIGURE 6 - CLOSEUP OF CPU SECTION, LCD MONITOR

WITH INTERIOR CIRCUIT BOARDS

VGA MONITOR
CONNECTOR
ON MONITOR

VGA MONITOR
CONNECTOR ON
MOTHERBOARD

GROUND

SCREW

TOUCHSCREEN

POWER

CONNECTOR

TOUCHSCREEN

CONTROLLER

TOUCHSCREEN

CONTROLLER

GROUND SCREW

TOUCHSCREEN

CONTROLLER

CABLE

LCD POWER
CONNECTOR

HINGE SCREWS
LOOSENED
FOR MONITOR
REMOVAL
(3 PER SIDE)

MONITOR

CABLE CLAMP

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE EVO (all models)/EVO Wallette/Elite Edge

Megatouch FORCE Technical Reference Manual

FIGURE 5 - CLOSEUP OF LCD MONITOR WITH EXTERIOR CIRCUIT BOARDS

SCREWS

FASTENING

LCD MOUNTING

PLATE TO

GAME

(6 PLACES)

SCREW AND

WASHER

FASTENING

STRAIN RELIEF

CORD

TIE WRAP

OSD BOARD

OSD CABLE

CONNECTIONS

INVERTER
BOARD

A TO D
BOARD

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

The Vibe and Vibe w/ Coin

Troubleshooting Information - Removal/Installation of Major Assemblies -

The Vibe and Vibe w/ Coin

Megatouch FORCE Technical Reference Manual

NOTE: Do NOT attempt to remove the monitor or motherboard from The Vibe. If these compo-
nents need to be replaced, contact Merit Customer Service at 1-800-445-9353 or (215) 639-
4700 outside the USA and Canada to arrange to have your game sent in for repair.

Hard Drive Removal

1. Turn off and unplug the game.

2. Unlock the lock on the processor cover and loosen the 3 screws on either side of the cover

(see Figure 1). Slide the cover away from the connector side of the processor and lift the cover
off of the unit.

3. Remove the 3 screws securing the hard drive to the processor (see Figure 2).

4. Disconnect the SA0345-01 I/O and audio harness, then remove the hard drive assembly until

you’re able to disconnect the hard drive ribbon cable and hard drive power connector. See
Figure 2.

5. Remove the 4 screws and shoulder washers fastening the hard drive to the mounting plate.

Hard Drive Installation

1. Fasten the new hard drive to the mounting plate with the 4 screws and shoulder washers.

2. Connect the ribbon cable and power connector to the hard drive, then reconnect the audio

harness.

3. Fasten the hard drive to the processor with the 3 screws (see Figure 2).

4. Replace the processor cover and tighten the 3 screws (see Figure 1).

5. Plug in and turn on the game.

Touchscreen Removal

1. Turn off and unplug the game.

2. Unlock and open the CPU section.

3. Games with bill acceptors only: Remove the clamp fastening the bill acceptor sensor cable to

the VGA monitor cable. Then disconnect the 12-pin power connector from the side of the bill
acceptor and remove the 4 screws and washers securing the bill acceptor to the CPU. You will
then be able to remove the bill acceptor.

4. Disconnect the VGA monitor cable connector and the screw fastening the cable to the monitor

mounting plate, and also disconnect the ground screw. Then disconnect the monitor power
connector. See Figure 3.

5. Remove the 2 thumbnuts securing the touchscreen controller to the game and remove the

controller from the mounting screws. Then disconnect the cable from the back of the controller
and disconnect the Molex connector (orange and gray wires) running from the touchscreen
controller cable to the main power harness. Also disconnect the ground screw. See Figure 3.

6. Using Figure 3, remove the 10 screws fastening the monitor to the bezel (2 screws also fasten

strain relief cords on either side of the CPU) and carefully pull the monitor assembly away from

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

The Vibe and Vibe w/ Coin (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

The Vibe and Vibe w/ Coin

Megatouch FORCE Technical Reference Manual

the bezel until you’re able to access the touchscreen. NOTE: Keep track of all hardware
removed in the touchscreen replacement process.

7. Note the orientation of the touchscreen cable before removing the screen. Then use dental

floss to carefully cut the foam tape holding the touchscreen to the monitor until you are able to
completely remove the screen. Note the manner in which the 2 layers of foam tape are placed
on the front edge of the screen.

8. Remove any remaining adhesive residue with denatured alcohol, then clean the monitor glass

with the supplied alcohol wipe.

Touchscreen Installation

1. Clean the reverse side of the replacement touchscreen with the supplied alcohol wipe.

2. If there is no tape already on the touchscreen, cut pieces of the supplied 1/2” double-sided

foam tape long enough to cover each edge of the screen without overlapping. After the tape is
in place on the screen, peel off the backing.

3. Replace the new touchscreen over the monitor in the same manner as the old screen, making

sure the screen is properly and evenly aligned over the monitor glass. Then clean the front of
the screen with the supplied alcohol wipe.

4. Using the original touchscreen for reference, cut pieces of the supplied 1/2” single-sided foam

tape long enough to cover each edge of the front of the screen without overlapping, then place
the tape on the screen. After the tape is in place, repeat this step so there are two layers of tape
on the screen.

5. Connect the new touchscreen controller cable in the back of the controller and secure the

controller on the mounting screws in the game with the existing hardware. Also connect the
Molex connector (orange and gray wires) to the main power harness.

6. Replace the monitor assembly in the bezel, lining up the screw holes in the monitor with the

holes in the bezel, then replace the 10 screws. See Figure 3.

7. Reconnect the VGA monitor cable connector and the screw fastening the cable to the monitor

mounting plate, and also reconnect the ground screw. Then reconnect the monitor power
connector. See Figure 3.

8. Games with bill acceptors only: Replace the bill acceptor in the CPU section (make sure the

touchscreen controller cables do not interfere) and fasten it with the 4 screws and washers.
Then reconnect the 12-pin bill acceptor power connector. It is also recommended you use a
cable clamp to refasten the bill acceptor sensor and VGA monitor cables.

9. Plug in and turn on the game.

10. When the game is finshed booting, calibrate the touchscreen.

11. Close and lock the CPU section.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Upright Fusion/Fune Zone

Motherboard Removal

1. Turn off and unplug the game.

2. Unlock and open the bezel.

Fun Zone games and Fusion games with electronic boxes only

: Remove the 2 screws

fastening the electronics box cover and move the cover aside.

3. Disconnect all connections to the motherboard, as well as any other connectors that may

interfere with removal of the board.

4. Using Figure 1, remove the 4 screws fastening the I/O board (the I/O board will be on the top or

left edge of the motherboard). Then carefully move the board aside until you’re able to remove
the 2 standoffs fastening the edge of the motherboard to the game (see Figure 2).

5. Remove the 2 screws fastening the other edge of the motherboard to the inside of the game

(see Figure 1), then carefully lift the motherboard out of the game and insert the board into an
anti-static bag for storage. NOTE: Be sure to read the Motherboard Handling Precautions
before handling the board.

Motherboard Installation

1. Place the new motherboard in the game and fasten one side with the 2 screws and the other

side with the 2 standoffs (see Figures 1 and 2) .

2. Fasten the I/O board and with the 4 screws (see Figure 1).

3. Reconnect all connections to the motherboard, as well as any harnesses that were discon-

nected earlier.

4. Close and lock the bezel.

Fun Zone games and Fusion games with electronic boxes only

: Replace the electronics

box cover and fasten it with the 2 screws.

5. Plug in and turn on the game.

Hard Drive Removal

1. Turn off and unplug the game.

2. Unlock and open the bezel.

Fun Zone games and Fusion games with electronic boxes only

: Remove the 2 screws

fastening the electronics box cover and move the cover aside.

3. Locate the hard drive. It will either be mounted to the electronics box cover or against the back

wall of the game. Remove the 3 screws or standoffs (see Figure 3) securing the hard drive
mounting bracket to the cover or the game, then remove the hard drive assembly until you’re
able to disconnect the hard drive power connector and hard drive ribbon cable.

4. Remove the 4 screws and shoulder washers fastening the hard drive to the mounting plate.

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Upright Fusion/Fun Zone

Megatouch FORCE Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Upright Fusion/Fun Zone (cont’d)

Hard Drive Installation

1. Fasten the new hard drive to the mounting plate with the 4 screws and shoulder washers.

2. Connect the power connector and ribbon cable to the hard drive, then fasten the hard drive

assembly to the electronics box cover or the game with the 3 screws or standoffs. See Figure
3.

3. Close and lock the bezel.

Games with electronic boxes only

: Replace the electronics box cover and fasten it with the

2 screws.

4. Plug in and turn on the game.

Monitor Removal

(Fun Zone games and Fusion games with electronic boxes)

1. Turn off and unplug the game.

2. Unlock and open the bezel.

3. Remove the 6 thumbnuts fastening the bezel to the game (see Figure 4) and remove the

bezel.

4. If you will not be reusing the existing touchscreen, remove the cable clamps securing the

touchscreen cable and the touchscreen power harness, then remove the screws fastening the
touchscreen controller (see Figure 4) to the game and disconnect the cable from the back of
the controller. Locate and disconnect the Molex connector (orange and gray wires) running
from the touchscreen controller cable to the main power harness, and also disconnect the
ground screw. See Figure 4.

If you will be reusing the existing touchscreen, disconnect the touchscreen controller cable
from the LCD panel (see Figure 4). Then use dental floss to carefully cut the foam tape holding
the touchscreen to the monitor until you are able to completely remove the screen. You will
need to place the touchscreen on a stable surface until it is installed on the new monitor. Then
remove any residual foam tape from the reverse side of the screen with denatured alcohol.

5. Disconnect the VGA monitor connector and ground screw, as well as the monitor power

connector. Standard monitors only: Also disconnect the monitor control board connector. See
Figure 4.

6. Remove the 4 screws fastening the monitor to the game (see Figure 5) and remove it. Be sure

to keep track of the plastic standoffs under the monitor.

Monitor Installation

(Fun Zone games and Fusion games with electronic boxes)

1. With the plastic standoffs in place, install the new monitor in the game and fasten it with the 4

screws (see Figure 5).

2. Connect the VGA monitor connector and ground screw to the new monitor, as well as the

monitor power connector. Standard monitors only: Also connect the monitor control board
connector. See Figure 4.

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Upright Fusion/Fun Zone

Megatouch FORCE Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Upright Fusion/Fun Zone (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Upright Fusion/Fun Zone

Megatouch FORCE Technical Reference Manual

3. If your replacement monitor already has a touchscreen, connect the touchscreen cable in the

back of the controller and secure the controller with the existing hardware. Also connect the
Molex connector (orange and gray wires) to the main power harness (after routing the wires
through the cable clamps) and attach the ground screw. See Figure 4.

If you are using the original touchscreen, clean the glass on the new LCD monitor with the
supplied alcohol wipe, then cut pieces of the supplied 1/2” foam tape long enough to cover
each edge of the monitor without overlapping. After the tape is in place on the monitor, peel off
the backing. Carefully place the touchscreen over the monitor in the same manner it was
attached to the old monitor, making sure the screen is properly and evenly aligned over the
glass, then connect the cable to the LCD panel (see Figure 4). Clean the front of the touchscreen
with the supplied alcohol wipe once it is in place.

4. Reinstall the bezel on the game and fasten it with the 6 thumbnuts.

5. Plug in and turn on the game.

6. When the game is finished booting, press the CALIBRATE button.

7. Close and lock the bezel, then calibrate the touchscreen.

Monitor Removal

(Fusion games without electronic boxes)

1. Turn off and unplug the game.

2. Unlock and open the bezel.

3. Disconnect the VGA monitor connector and ground screw, the monitor control board connector,

and the monitor power connector and also remove the cables from the 2 clamps attached to
the monitor. See Figure 6.

4. If you will not be reusing the existing touchscreen, remove the screws fastening the touchscreen

controller to the game and disconnect the cable from the back of the controller. Then locate
and disconnect the Molex connector (orange and gray wires) running from the touchscreen
controller cable to the main power harness. After disconnecting the ground screw, pull the
cables out of the clamps. See Figures 7 and 8.

If you will be reusing the existing touchscreen, disconnect the touchscreen controller cable
from the LCD panel (see Figure 7).

5. Remove the 10 screws securing the plastic bezel to the wooden frame (see Figure 6) and

carefully remove the bezel from the game. Be careful not to damage the bezel with the coin
cup during removal. NOTE: Keep track of all hardware removed in the monitor replacement
process.

6. Place the bezel assembly upside-down on a flat surface and remove the 10 screws fastening

the LCD monitor to the bezel (remember which 2 screws also fasten cable clamps), then
remove the monitor from the bezel. See Figure 9. NOTE: Be sure the glass is not scratched
when setting the monitor aside.

7. If you will not be reusing the existing touchscreen, continue with installing the new monitor. If

you will be reusing the touchscreen, note the orientation of the screen (i.e., the positioning of
the ribbon cable and which side is the front) before removing it from the LCD monitor. Then

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Upright Fusion/Fun Zone (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Upright Fusion/Fun Zone

Megatouch FORCE Technical Reference Manual

use dental floss to carefully cut the foam tape holding the screen to the monitor. Once the
touchscreen is completely free from the monitor, remove any residual foam tape from the
screen with denatured alcohol and clean the glass with the supplied alcohol wipe.

Monitor Installation

(Fusion games without electronic boxes)

1. If your replacement monitor already has a touchscreen, skip to step 3. If you will be using the

original touchscreen, clean the glass on the new LCD monitor with the supplied alcohol wipe,
then cut pieces of the supplied 1/2” foam tape long enough to cover each edge of the monitor
without overlapping. After the tape is in place on the monitor, peel off the backing.

2. Carefully place the touchscreen over the monitor in the same manner it was attached to the

old monitor, making sure the screen is properly and evenly aligned over the glass. Clean the
front of the touchscreen with the supplied alcohol wipe once it is in place.

3. Place the new LCD monitor in the bezel (make sure it is not upside-down), lining up the screw

holes on the face of the mounting frame with the larger, drilled holes on the plastic mounting
pieces (see Figure 10), and fasten it with the 10 screws. Also replace the cable clamps in the
appropriate screw holes. See Figure 9.

4. Carefully replace the plastic bezel assembly in the game, making sure the coin cup protrudes

into the lower cutout and no wires are pinched, then secure it to the wooden frame with the 10
screws (see Figure 6).

5. If the monitor has a new touchscreen, connect the touchscreen controller cable in the back of

the controller and secure the controller in the game with the existing hardware. Then connect
the Molex connector (orange and gray wires) to the main power harness and attach the ground
screw. Replace the cables in the clamps as before. See Figure 8.

If the monitor has the original touchscreen, reconnect the touchscreen controller cable to the
LCD panel (see Figure 7).

6. Connect the VGA monitor connector and ground screw (do not overtighten), the monitor control

board connector, and the monitor power connector (see Figure 6) to the new monitor and
replace the cables in the 2 clamps attached to the monitor.

7. Plug in and turn on the game.

8. When the game is finished booting, press the CALIBRATE button.

9. Close and lock the bezel, then calibrate the touchscreen.

Touchscreen Removal

(Fun Zone games and Fusion games with electronic boxes)

1. Turn off and unplug the game.

2. Unlock and open the bezel.

3. Remove the 6 thumbnuts fastening the bezel to the game (see Figure 4) and remove the

bezel.

4. Remove the cable clamps securing the touchscreen cable and the touchscreen power harness,

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Upright Fusion/Fun Zone

Megatouch FORCE Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Upright Fusion/Fun Zone (cont’d)

then remove the screws fastening the touchscreen controller (see Figure 4) to the game and
disconnect the cable from the back of the controller. Locate and disconnect the Molex connector
(orange and gray wires) running from the touchscreen controller cable to the main power
harness, and also disconnect the ground screw. See Figure 4.

5. Use dental floss to carefully cut the foam tape holding the touchscreen to the monitor until you

are able to completely remove the screen. Once the touchscreen is completely free from the
monitor, remove any residual foam tape from the monitor with denatured alcohol.

Touchscreen Installation

(Fun Zone game and Fusion games with electronic boxes)

1. Clean the glass on the reverse side of the new touchscreen with the supplied alcohol wipe,

then cut pieces of the supplied 1/2” foam tape long enough to cover each edge of the monitor
without overlapping. After the tape is in place on the monitor, peel off the backing. Carefully
place the touchscreen over the monitor in the same manner it was attached to the old monitor,
making sure the screen is properly and evenly aligned over the glass. Clean the front of the
touchscreen with the supplied alcohol wipe once it is in place.

2. Connect the touchscreen cable in the back of the controller and secure the controller with the

existing hardware. Also connect the Molex connector (orange and gray wires) to the main
power harness (after routing the wires through the cable clamps) and attach the ground screw.
See Figure 4.

3. Reinstall the bezel on the game and fasten it with the 6 thumbnuts.

4. Plug in and turn on the game.

5. When the game is finished booting, press the CALIBRATE button.

6. Close and lock the bezel, then calibrate the touchscreen.

Touchscreen Removal

(Fun Zone games and Fusion games without electronic boxes)

1. Turn off and unplug the game.

2. Unlock and open the bezel.

3. Disconnect the VGA monitor connector and ground screw, the monitor control board connector,

and the monitor power connector and also remove the cables from the 2 clamps attached to
the monitor. See Figure 6.

4. Remove the screws fastening the touchscreen controller to the game and disconnect the

cable from the back of the controller. Then locate and disconnect the Molex connector (orange
and gray wires) running from the touchscreen controller cable to the main power harness.
After disconnecting the ground screw, pull the cables out of the clamps. See Figures 7 and 8.

5. Remove the 10 screws securing the plastic bezel to the wooden frame (see Figure 6) and

carefully remove the bezel from the game. Be careful not to damage the bezel with the coin
cup during removal. NOTE: Keep track of all hardware removed in the touchscreen replacement
process.

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Upright Fusion/Fun Zone

Megatouch FORCE Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Upright Fusion/Fun Zone (cont’d)

6. Place the bezel assembly upside-down on a flat surface and remove the 10 screws

fastening the LCD monitor to the bezel (remember which 2 screws also fasten cable
clamps), then remove the monitor from the bezel. See Figure 9. NOTE: Be sure the glass
is not scratched when setting the monitor aside.

7. Note the orientation of the touchscreen cable before removing the screen. Then use dental

floss to carefully cut the foam tape holding the touchscreen to the monitor until you are able
to completely remove the screen. Once the touchscreen is completely free from the
monitor, remove any residual foam tape from the monitor with denatured alcohol.

Touchscreen Installation

(Fusion games without electronic boxes)

1. Clean the glass on the reverse side of the new touchscreen with the supplied alcohol

wipe, then cut pieces of the supplied 1/2” foam tape long enough to cover each edge of the
monitor without overlapping. After the tape is in place on the monitor, peel off the backing.

2. Carefully place the touchscreen over the monitor in the same manner as the old screen,

making sure the screen is properly and evenly aligned over the glass. Then clean the front
of the screen with the supplied alcohol wipe.

3. Place the new LCD monitor in the bezel (make sure it is not upside-down), lining up the

screw holes on the face of the mounting frame with the larger, drilled holes on the plastic
mounting pieces (see Figure 10), and fasten it with the 10 screws. Also replace the cable
clamps in the appropriate screw holes (See Figure 9).

4. Carefully replace the plastic bezel assembly in the game, making sure the coin cup

protrudes into the lower cutout and no wires are pinched, then secure it to the wooden
frame with the 10 screws (see Figure 6).

5. Connect the touchscreen controller cable in the back of the controller and secure the

controller in the game with the existing hardware. Then connect the Molex connector
(orange and gray wires) to the main power harness and attach the ground screw. Replace
the cables in the clamps as before. See Figure 8.

6. Reconnect the VGA monitor connector and ground screw (do not overtighten), the monitor

control board connector, and the monitor power connector (see Figure 6) and replace the
cables in the 2 clamps attached to the monitor.

7. Plug in and turn on the game.

8. When the game is finished booting, press the CALIBRATE button.

9. Close and lock the bezel, then calibrate the touchscreen.

FIGURE 2 - CPU SECTION

FIGURE 1 - MOTHERBOARD AND I/O BOARD

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Upright Fusion/Fun Zone

Megatouch FORCE Technical Reference Manual

STANDOFFS

FASTENING

EDGE OF

MOTHERBOARD

(2 PLACES)

I/O BOARD

MOVED ASIDE

SCREWS

FASTENING

I/O BOARD

(4 PLACES)

SCREWS

FASTENING

EDGE OF

MOTHERBOARD

(2 PLACES)

FIGURE 3 - HARD DRIVE

POWER
CONNECTOR

RIBBON
CABLE

HARDWARE

FASTENING

HARD DRIVE

TO MOUNTING

PLATE

(3 PLACES)

SCREWS AND

SHOULDER

WASHERS

FASTENING

HARD DRIVE TO

MOUNTING

PLATE

(4 PLACES)

Motherboard Removal

1. Turn off and unplug the game.

2. Unlock and open the front bezel.

3. Slide the CPU shelf into its service position to access the motherboard.

4. Disconnect all connections to the motherboard.

5. Remove the 4 screws mounting the motherboard to the CPU shelf (see Figure 1) and carefully

remove the board. Insert the board into an anti-static bag for storage. NOTE: Be sure to read
the Motherboard Handling Precautions before handling the board.

Motherboard Installation

1. Place the new motherboard on the CPU shelf and fasten it with the 4 screws.

2. Reconnect all connections to the motherboard.

3. Slide the CPU shelf back into the game.

4. Close and lock the front bezel.

5. Plug in and turn on the game.

Hard Drive Removal

1. Turn off and unplug the game.

2. Unlock and open the front bezel.

3. Slide the CPU shelf into its service position to access the hard drive.

4. Remove the screw securing the hard drive mounting plate to the shelf (see Figure 2).

5. Remove the 4 screws and shoulder washers fastening the hard drive to the mounting plate.

6. Disconnect the hard drive ribbon cable and the hard drive power connector.

Hard Drive Installation

1. Plug the ribbon cable and power connector into the new hard drive.

2. Fasten the hard drive to the mounting plate with the 4 screws and shoulder washers.

3. Fasten the hard drive mounting plate to the CPU shelf with the mounting screw (see Figure 2).

4. Slide the CPU shelf back into the game.

5. Close and lock the front bezel.

6. Plug in and turn on the game.

Monitor Removal

1. Turn off and unplug the game.

2. Open the rear door to gain access to the monitor. See Figure 3.

3. Disconnect all harnesses from the monitor.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Upright w/o Coin Door

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Upright w/o Coin Door

Megatouch FORCE Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Upright w/o Coin Door (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Upright w/o Coin Door

Megatouch FORCE Technical Reference Manual

4. Remove the screws fastening the touchscreen controller to the game, then disconnect the

cable from the back of the controller and disconnect the Molex connector (orange and gray
wires) running from the touchscreen controller cable to the main power harness.

5. Remove both bolts securing the rear of the monitor shelf to the cabinet. See Figure 4.

6. Open the front bezel.

7. Remove both bolts securing the front of the monitor shelf to the cabinet (located on the under-

side of the shelf). See Figure 4.

8. Remove the ground strap attached to the monitor door.

9. Pull the monitor up and out through the front of the game.

Monitor Installation

1. Place the new monitor in the game.

2. Replace the ground strap on the monitor door.

3. Fasten the front of the monitor shelf to the cabinet with the 2 bolts (see Figure 4).

4. Close the front bezel.

5. Secure the rear of the monitor shelf to the cabinet with the 2 bolts (see Figure 4).

6. Connect the touchscreen cable in the back of the controller and secure the controller in the

game with the existing hardware. Also connect the Molex connector (orange and gray wires) to
the main power harness.

7. Reconnect all harnesses to the monitor.

8. Close the rear door.

9. Plug in and turn on the game.

Touchscreen Removal

1. Turn off and unplug the game.

2. Unlock and open the front bezel (see Figure 5).

3. Remove the black poly tape (see Figure 5) from around the edges of the old touchscreen,

keeping the manner in which the tape was placed around the screen in mind.

4. Remove the two nuts and washers securing the touchscreen controller to the game and re-

move the controller from the mounting screws. Then disconnect the cable from the back of the
controller and disconnect the Molex connector (orange and gray wires) running from the touch-
screen controller cable to the main power harness.

5. Use dental floss to carefully cut the foam tape holding the touchscreen to the picture tube until

you are able to completely remove the touchscreen.

6. Remove any remaining adhesive residue with denatured alcohol, then wipe the surface of the

picture tube with the supplied alcohol wipe.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Upright w/o Coin Door (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Upright w/o Coin Door

Megatouch FORCE Technical Reference Manual

Touchscreen Installation

1. Clean the reverse side of the replacement touchscreen with the supplied alcohol wipe.

2. Peel the backing from the 8 pieces of double-sided foam tape already adhered to the reverse

side of the touchscreen.

3. Replace the new touchscreen over the picture tube (with the cable on the right if you are facing

the game), making sure the screen is properly and evenly aligned over the picture tube. Then
clean the front of the screen with the supplied alcohol wipe.

4. Connect the new touchscreen cable in the back of the controller and secure the controller on

the mounting screws in the game with the existing hardware. Also connect the Molex connec-
tor (orange and gray wires) to the main power harness.

5. Remembering the manner in which the tape was placed around the touchscreen you removed,

place and cut a length of the supplied black poly tape evenly over an entire edge of the touch-
screen and repeat until all 4 edges are covered.

6. Place and cut a longer length of black poly tape around all 4 edges of the screen.

7. Plug in and turn on the game.

8. When the game is finshed booting, calibrate the touchscreen.

9. Close and lock the front bezel.

FIGURE 1 – MOTHERBOARD REMOVAL –

LOCATION OF SCREWS SECURING MOTHERBOARD TO CPU SHELF

Motherboard Removal

1. Turn off and unplug the game.

2. Unlock and open the front door to access the electronics shelf.

3. Disconnect all connections to the motherboard.

4. Remove the 2 screws securing the centronics ribbon cable and move it aside. See Figure 1.

5. Remove the 4 screws mounting the motherboard to the CPU shelf (see Figure 2) and carefully

remove the board. Insert the board into an anti-static bag for storage. NOTE: Be sure to read
the Motherboard Handling Precautions before handling the board.

Motherboard Installation

1. Place the new motherboard on the CPU shelf and fasten it with the 4 screws. See Figure 2.

2. Resecure the centronics ribbon cable with the 2 screws. See Figure 1.

3. Reconnect all connections to the motherboard.

4. Close and lock the front door.

5. Plug in and turn on the game.

Hard Drive Removal

1. Turn off and unplug the game.

2. Unlock and open the front door to access the electronics shelf.

3. Remove the 2 screws securing the I/O board mounting plate to the hard drive mounting plate

(see Figure 3). The I/O board assembly will need to be moved aside in order to access the
hard drive.

4. Remove the screw securing the hard drive mounting plate to the game (see Figure 1).

5. Remove the 4 screws and shoulder washers fastening the hard drive to the mounting plate.

6. Disconnect the hard drive ribbon cable and the hard drive power connector.

Hard Drive Installation

1. Plug the ribbon cable and power connector into the new hard drive.

2. Fasten the hard drive to the mounting plate with the 4 screws and shoulder washers.

3. Fasten the hard drive mounting plate to the game with the mounting screw (see Figure 1).

4. Fasten the I/O board mounting plate to the hard drive mounting plate with the 2 screws (see

Figure 3).

5. Close and lock the front door.

6. Plug in and turn on the game.

Monitor Removal

1. Turn off and unplug the game.

2. Unlock and open the rear door to gain access to the monitor. See Figure 4.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Upright w/ Coin Door

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Upright w/ Coin Door

Megatouch FORCE Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Upright w/ Coin Door (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Upright w/ Coin Door

Megatouch FORCE Technical Reference Manual

3. Disconnect all harnesses from the monitor.

4. Remove the hardware fastening the touchscreen controller to the game, then disconnect the

cable from the back of the controller and disconnect the Molex connector (orange and gray
wires) running from the touchscreen controller cable to the main power harness.

5. Remove both bolts securing the rear of the monitor shelf to the cabinet. See Figure 5.

6. To remove the front bezel, remove the 2 wing nuts inside the CPU door along the bottom of the

bezel and the 3 wing nuts inside the game along the top piece. Then disconnect the 2 speaker
connectors inside the game on either side of the marquee before lifting the bezel from the
game.

7. Remove both bolts securing the front of the monitor shelf to the cabinet (located on the under-

side of the shelf). See Figure 5.

8. Remove the ground strap attached to the monitor door.

9. Pull the monitor up and out through the front of the game.

Monitor Installation

1. Place the new monitor in the game.

2. Replace the ground strap on the monitor door.

3. Fasten the front of the monitor shelf to the cabinet with the 2 bolts (see Figure 5).

4. Replace the front bezel and the 5 wing nuts (2 inside the CPU door along the bottom of the

bezel, 3 along the top piece) fastening it to the game. Then reconnect the 2 speaker connec-
tors inside the game.

5. Fasten the rear of the monitor shelf to the cabinet with the 2 bolts (see Figure 5).

6. Connect the touchscreen cable in the back of the controller and secure the controller in the

game with the existing hardware. Also connect the Molex connector (orange and gray wires) to
the main power harness.

7. Reconnect all harnesses to the monitor.

8. Close and lock the rear door.

9. Plug in and turn on the game.

Touchscreen Removal

1. Turn off and unplug the game.

2. Remove the bezel by removing the 2 wing nuts inside the CPU door along the bottom of the

bezel and the 3 wing nuts inside the game along the top piece (after removing the rear door).
Then disconnect the 2 speaker connectors inside the game on either side of the marquee
before lifting the bezel from the game.

3. Remove the black poly tape (see Figure 6) from around the edges of the old touchscreen,

keeping the manner in which the tape was placed around the screen in mind.

4. Remove the two nuts and washers securing the touchscreen controller to the game and re-

move the controller from the mounting screws. Then disconnect the cable from the back of the

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

FORCE Upright w/ Coin Door (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

FORCE Upright w/ Coin Door

Megatouch FORCE Technical Reference Manual

controller and disconnect the Molex connector (orange and gray wires) running from the touch-
screen controller cable to the main power harness.

5. Use dental floss to carefully cut the foam tape holding the touchscreen to the picture tube until

you are able to completely remove the touchscreen.

6. Remove any remaining adhesive residue with denatured alcohol, then wipe the surface of the

picture tube with the supplied alcohol wipe.

Touchscreen Installation

1. Clean the reverse side of the replacement touchscreen with the supplied alcohol wipe.

2. Peel the backing from the 8 pieces of double-sided foam tape already adhered to the reverse

side of the touchscreen.

3. Replace the new touchscreen over the picture tube (with the cable on the right if you are facing

the game), making sure the screen is properly and evenly aligned over the picture tube. Then
clean the front of the screen with the supplied alcohol wipe.

4. Connect the new touchscreen controller cable in the back of the controller and secure the

controller on the mounting screws in the game with the existing hardware. Also connect the
Molex connector (orange and gray wires) to the main power harness.

5. Remembering the manner in which the tape was placed around the touchscreen you removed,

place and cut a length of the supplied black poly tape evenly over an entire edge of the touch-
screen and repeat until all 4 edges are covered.

6. Place and cut a longer length of black poly tape around all 4 edges of the screen.

7. Plug in and turn on the game.

8. When the game is finshed booting, calibrate the touchscreen.

9. Replace the bezel and secure it with the 5 wing nuts removed earlier. Also reconnect the 2

speaker connectors, then replace the rear door.

Hard Drive Removal

1. Turn off the main power switch on the outside of the game.

2. Unlock and remove the rear door, then turn off the internal power switch (located above the

cooling fan on the left side). Then unplug the game.

3. Disconnect all connections to the I/O board on the electronics shelf. This will allow for I/O

board and hard drive removal.

4. Disconnect the power connector and the ribbon cable from the hard drive.

5. Remove the screw securing the hard drive and I/O board assemblies to the electronics tray

and remove them from the unit (see Figure 1).

6. Remove the 4 screws securing the I/O board to the mounting plate above the hard drive and

remove the I/O board (see Figure 1). Then remove the 2 screws fastening the I/O board
mounting plate to the hard drive and remove the hard drive assembly.

7. Remove the 4 screws and shoulder washers fastening the hard drive to the hard drive mount-

ing plate.

Hard Drive Installation

1. Fasten the new hard drive to the mounting plate with the 4 screws and shoulder washers.

2. Fasten the I/O board mounting plate to the hard drive assembly with the 2 screws, then fasten

the I/O board to the mounting plate with the 4 screws (see Figure 1).

3. Fasten the hard drive and I/O board assemblies to the electronics tray with the mounting screw

(see Figure 1).

4. Connect the power connector and ribbon cable to the hard drive.

5. Reconnect all connections to the I/O board.

6. Plug in the game, then turn on the internal power switch and replace and lock the rear door.

7. Turn on the main power switch on the outside of the game.

Motherboard Removal

1. Turn off the main power switch on the outside of the game.

2. Unlock and remove the rear door, then turn off the internal power switch (located above the

cooling fan on the left side). Then unplug the game.

3. Disconnect all connections to the I/O board. This will allow for I/O board and hard drive re-

moval.

4. Disconnect the power connector from the hard drive and the hard drive ribbon cable from the

motherboard.

5. Remove the screw securing the hard drive and I/O board assemblies to the electronics tray

and remove them from the unit (see Figure 1).

6. Disconnect all connections to the motherboard.

7. Remove the 2 screws securing the centronics ribbon cable and move it aside (see Figure 1).

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Megatouch Combo Jukebox

Troubleshooting Information - Removal/Installation of Major Assemblies -

Megatouch Combo Jukebox

Megatouch FORCE Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Megatouch Combo Jukebox (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

Megatouch Combo Jukebox

Megatouch FORCE Technical Reference Manual

8. Remove the 4 screws mounting the motherboard to the CPU shelf (see Figure 1) and carefully

remove the board. Insert the board into an anti-static bag for storage. NOTE: Be sure to read
the Motherboard Handling Precautions before handling the board.

Motherboard Installation

1. Fasten the new motherboard to the CPU shelf (see Figure 1) with the 4 screws.

2. Resecure the centronics cable with the 2 screws.

3. Reconnect all connections to the motherboard.

4. Fasten the hard drive and I/O board assemblies to the electronics tray with the mounting screw

(see Figure 1).

5. Reconnect the power connector to the hard drive and the hard drive ribbon cable to the

motherboard.

6. Reconnect all connections to the I/O board.

7. Plug in the game, then turn on the internal power switch and replace and lock the rear door.

8. Turn on the main power switch on the outside of the game.

Monitor Removal

1. Turn off the main power switch on the outside of the game.

2. Unlock and remove the rear door, then turn off the internal power switch (located above the

cooling fan on the left side). Then unplug the game.

3. Disconnect all harnesses from the monitor.

4. Using Figure 2, locate the touchscreen controller mounted inside the cabinet on the right side (if

you are facing the rear of the game) and remove the two screws fastening the controller to the
cabinet. Then disconnect the Molex connector (orange and gray wires) running from the touch-
screen controller cable to the main power harness.

5. Remove the screws securing the 2 clamps fastening the power cable to the fluorescent light

assembly (after removing the upper screw, immediately replace it in order to keep the fan
assembly fastened). Then move the cable aside in order to make room for monitor removal.
You may need to disconnect one of the fan power harnesses as well.

6. Remove the 3 hex bolts on either side of the mounting plate (see Figure 3) fastening the plate to

the 2 monitor mounting brackets inside the unit.

7. Remove the 2 lower nuts and bolts (one on each side) fastening the monitor mounting brackets

to the unit (see Figure 3). This will allow room to slide out the monitor assembly.

8. Carefully remove the monitor assembly from the game. Disconnect other wires and harnesses

if necessary.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Megatouch Combo Jukebox (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

Megatouch Combo Jukebox

Megatouch FORCE Technical Reference Manual

Monitor Installation

1. Place the new monitor assembly in the game.

2. Replace the 2 lower nuts and bolts through the monitor mounting brackets to fasten the monitor

to the game.

3. Fasten the mounting plate to the monitor mounting brackets with the 3 hex bolts (see Figure 3).

4. Connect the new touchscreen controller cable in the back of the controller and secure the

controller with the existing hardware. Also connect the Molex connector (orange and gray
wires) to the main power harness.

5. Reconnect the all harnesses to the monitor, as well as any other harnesses that were discon-

nected when removing the monitor. Also replace the power cable to the fluorescent light as-
sembly in the clamps.

6. Plug in the game, then turn on the internal power switch and replace and lock the rear door.

7. Turn on the main power switch on the outside of the game.

8. Calibrate the touchscreen.

Touchscreen Removal

1. Turn off the main power switch on the outside of the game.

2. Unlock and remove the rear door, then turn off the internal power switch (located above the

cooling fan on the left side). Then unplug the game.

3. Using Figures 4 and 5, remove the 6 bolts and wing nuts (3 per side) fastening the front bezel

to the cabinet and remove the bezel.

4. Using Figure 2, locate the touchscreen controller mounted inside the cabinet on the right side (if

5. Remove the black poly tape from around the edges of the old touchscreen (see Figure 6).

Remember how the tape was placed in order to tape the new touchscreen.

6. Use dental floss to carefully cut the foam tape holding the touchscreen to the picture tube until

you are able to completely remove the touchscreen.

7. Remove any remaining adhesive residue with denatured alcohol, then wipe the surface of the

picture tube with the supplied alcohol wipe.

Touchscreen Installation

1. Clean the reverse side of the replacement touchscreen with the supplied alcohol wipe.

2. If there is no tape already on the touchscreen, cut pieces of the supplied 1/2” foam tape long

enough to cover each edge of the screen without overlapping. After the tape is in place on the
screen, peel off the backing.

3. Replace the new touchscreen over the monitor (with the cable on the left if you are facing the

game), making sure the screen is properly and evenly aligned over the picture tube. Then

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Megatouch Combo Jukebox (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

Megatouch Combo Jukebox

Megatouch FORCE Technical Reference Manual

clean the front of the screen with the supplied alcohol wipe.

4. Remembering the manner in which the tape was placed around the original touchscreen, place

and cut a length of the supplied black poly tape evenly over an entire edge of the touchscreen
and repeat until all 4 edges are covered.

5. Place and cut a longer length of black poly tape around all 4 edges of the screen.

6. Connect the new touchscreen controller cable in the back of the controller and secure the

controller with the existing hardware. Also connect the Molex connector (orange and gray
wires) to the main power harness.

7. Carefully replace the front bezel, lining up the holes in the bezel with the screw holes on the

game. Then replace the 6 bolts and wing nuts (3 per side) fastening the bezel to the game.
Refer to Figures 4 and 5.

8. Plug in the game, then turn on the internal power switch and replace and lock the rear door.

9. Turn on the main power switch on the outside of the game.

10. Calibrate the touchscreen.

SCREWS SECURING
CENTRONICS RIBBON CABLE

SCREWS SECURING

MOTHERBOARD TO

ELECTRONICS TRAY

(4 PLACES)

SCREWS SECURING I/O

BOARD TO MOUNTING PLATE

(4 PLACES)

SCREWS SECURING HARD DRIVE
TO HARD DRIVE MOUNTING PLATE
(4 PLACES)

SCREW

SECURING

HARD DRIVE

FIGURE 1 - REMOVING HARD DRIVE/MOTHERBOARD

Hard Drive Removal

1. Turn off and unplug the game.

2. Unlock and remove the lower rear door.

3. Remove the nuts fastening the electronics tray to the game. The side wall mounted tray will

have 4 nuts (see Figure 1). The bottom mounted tray will have 3 nuts, 2 in the right front corner
and 1 on the left side by the power strip (see Figure 2).

4. Disconnect any connections or cables preventing the electronics tray from being removed

from the game, then remove the tray. Be sure to keep track of what was disconnected.

5. Remove the 4 screws and shoulder washers fastening the hard drive to the mounting plate on

the electronics tray, then slide out the hard drive from under the I/O board until you’re able to
disconnect the power connector and ribbon cable from the drive. See Figure 2.

Hard Drive Installation

1. Place the new hard drive under the I/O board and connect the power connector and ribbon

cable to the drive, then fasten the drive to the mounting plate with the 4 screws and shoulder
washers (see Figure 2)

2. Replace the electronics tray in the game and fasten it with the same nuts removed in step 3

(see Figure 1 or Figure 2).

3. Reconnect any connections from step 4 above.

4. Replace and lock the rear door.

5. Plug in and turn on the game.

Motherboard Removal

1. Turn off and unplug the game.

2. Unlock and remove the rear door.

3. Remove the nuts fastening the electronics tray to the game. The side wall mounted tray will

have 4 nuts (see Figure 1). The bottom mounted tray will have 3 nuts, 2 in the right front corner
and 1 on the left side by the power strip (see Figure 2).

4. Disconnect any connections or cables preventing the electronics tray from being removed

from the game, then remove the tray. Be sure to keep track of what was disconnected.

5. Disconnect all connections to the motherboard. Be sure to keep track of what was discon-

nected.

6. Side wall mounted tray: Remove the 4 screws mounting the motherboard to the electronics

tray. Bottom mounted tray: Release the locking head of the nylon standoffs by pushing in the

sides (see Figure 4 for both locations). Carefully remove the board and insert into an anti-static

bag for storage. NOTE: Be sure to read the Motherboard Handling Precautions before han-

dling the board.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Mr. VIPS

Troubleshooting Information - Removal/Installation of Major Assemblies - Mr. VIPS

Megatouch FORCE Technical Reference Manual

Motherboard Installation

1. Place the new motherboard on the electronics tray and secure it with the 4 screws or nylon

standoffs (see Figure 4).

2. Reconnect all connections to the motherboard.

3. Replace the electronics tray in the game and fasten it with the nuts. See Figure 1 or Figure 2.

4. Reconnect any connections from step 4 above.

5. Replace and lock the rear door.

6. Plug in and turnon the game.

Power Supply Removal

1. Turn off and unplug the game.

2. Unlock and remove the rear door.

3. Unplug the IEC connector from the power supply.

4. Disconnect all connections to the main power supply harness.

5. If the power supply is fastened to the game with a metal strap (see Figure 5) and double-sided

tape, remove the 2 screws fastening the strap, then carefully pull the power supply off the
double-sided tape and out of the game. For games without the metal strap, remove the 2
screws fastening the power supply to the game (see Figure 6).

Power Supply Installation

1. Install the new power supply in the game in the same manner as the old power supply and

fasten it with the existing hardware. If applicable, use double-sided tape to ensure the power
supply is firmly held in place.

2. Reconnect all connections to the main power supply harness.

3. Plug the IEC connector into the new power supply.

4. Replace and lock the rear door.

5. Plug in and turn on the game.

Monitor Removal

1. Turn off and unplug the game.

2. Unlock and remove the upper rear door.

3. To remove the large prize assembly, first remove the 2 nuts and bolts fastening the cap and

unplug the fluorescent light assembly, then remove the remaining 8 nuts and bolts fastening the
prize assembly to the game. The cap and prize assembly can be removed together. See
Figure 7.

4. Remove the cable clamp fastening the small prize assembly light wiring to the monitor frame.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Mr. VIPS (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies - Mr. VIPS

Megatouch FORCE Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Mr. VIPS (cont’d)

See Figure 6.

5. From inside the game, access and remove the 4 screws (2 per side) fastening the sides of the

shroud to the game. See Figure 9.

6. To completely remove the shroud and proceed with monitor removal, first determine the type of

hardware securing the shroud to your game. See Figures 10 and 11.

Games with screws securing front of shroud:

Remove the 4 screws from under the moni-

tor (see Figure 10), then carefully remove the shroud and small prize assembly from the game.
Then remove the bolts and nuts (there may be as many as 6) securing themonitor to the game
(see Figures 12-14 for possible locations).

Games with bolts securing front of shroud:

Remove the bolts and nuts (there may be as

many as 6) securing the monitor to the game (see Figures 12-14 for possible locations). Then
carefully pull the monitor towards you until you have enough room to access the 4 nuts secur-
ing the bolts holding the front of the shroud to the game. Remove the nuts and bolts, then
carefully remove the shroud and small prize assembly from the game.

7. Remove the two nuts and washers securing the touchscreen controller to the inside of the

monitor (see Figure 15) and remove the controller from the mounting screws. Then discon-
nect the cable from the back of the controller and disconnect the Molex connector (orange and
gray wires) running from the touchscreen controller cable to the main power harness.

8. Disconnect all harnesses from the monitor.

9. Remove the monitor from the game.

Monitor Installation

1. Place the new monitor in the game. If the front of the shroud was secured with bolts, be sure to

temporarily leave enough room in front of the monitor to replace the mounting hardware.

2. Reconnect all harnesses to the monitor.

3. Connect the new touchscreen controller cable in the back of the controller and secure the

controller on the mounting screws in the game with the existing hardware (see Figure 15). Also
connect the Molex connector (orange and gray wires) to the main power harness.

4. Replace the shroud and the prize assembly, then secure the front of the shroud with the exist-

ing hardware.

5. Secure the monitor in the game with the existing hardware. See Figures 12-14.

6. From inside the game, replace the 4 screws (2 per side) fastening the sides of the shroud to

the game. See Figure 9.

7. Fasten the small prize assembly light wiring to the monitor frame with a new cable clamp as

shown in Figure 8.

8. Replace the cap and large prize assembly, then replace the 8 nuts and bolts fastening the prize

assembly to the game. Then replace the 2 nuts and bolts fastening the cap to the game and
plug in the fluorescent light. See Figure 7.

9. Replace and lock the upper rear door.

Troubleshooting Information - Removal/Installation of Major Assemblies - Mr. VIPS

Megatouch FORCE Technical Reference Manual

Troubleshooting Information - Removal/Installation of Major Assemblies - Mr. VIPS

Megatouch FORCE Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Mr. VIPS (cont’d)

10. Plug in and turn on the game.

Touchscreen Removal

1. Turn off and unplug the game.

2. Unlock and remove the upper rear door.

3. To remove the large prize assembly, first remove the 2 nuts and bolts fastening the cap and

unplug the fluorescent light assembly, then remove the remaining 8 nuts and bolts fastening the
prize assembly to the game. The cap and prize assembly can be removed together. See
Figure 7.

4. To proceed with touchscreen removal, first determine the type of hardware securing the shroud

to your game. See Figures 10 and 11.

Games with screws securing front of shroud:

•

To remove the front bezel from the shroud, remove the 4 screws on the underside of
the bezel (see Figure 10), then remove the 4 screws (2 per side) on either side of the
front bezel (see Figure 16). The bezel can then be removed.

Games with bolts securing front of shroud:

•

Remove the cable clamp fastening the small prize assembly light wiring to the moni-
tor frame. See Figure 8.

•

From inside the game, access and remove the 4 screws (2 per side) fastening the
sides of the shroud to the game. See Figure 9.

•

Remove the bolts and nuts (there may be as many as 6) securing themonitor to the
game (see Figures 11-14 for possible locations). Then carefully pull the monitor
towards you until you have enough room to access the 4 nuts securing the bolts
holding the front of the shroud to the game. Remove the nuts and bolts, then carefully
remove the shroud and small prize assembly from the game.

5. Remove the black poly tape (see Figure 17) from around the edges of the old touchscreen,

keeping the manner in which the tape was placed around the screen in mind.

6. Remove the two nuts and washers securing the touchscreen controller to the inside of the

7. Use dental floss to carefully cut the foam tape holding the touchscreen to the picture tube until

you are able to completely remove the touchscreen.

8. Remove any remaining adhesive residue with denatured alcohol, then wipe the surface of the

picture tube with the supplied alcohol wipe.

Touchscreen Installation

1. Clean the reverse side of the replacement touchscreen with the supplied alcohol wipe.

Troubleshooting Information - Removal/Installation of Major Assemblies - Mr. VIPS

Megatouch FORCE Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Mr. VIPS (cont’d)

2. Peel the backing from the 8 pieces of double-sided foam tape already adhered to the reverse

side of the touchscreen.

3. Replace the new touchscreen over the picture tube (with the cable on the right if you are facing

the game), making sure the screen is properly and evenly aligned over the picture tube. Then
clean the front of the screen with the supplied alcohol wipe.

4. Connect the new touchscreen controller cable in the back of the controller and secure the

controller on the mounting screws in the game with the existing hardware (see Figure 15). Also
connect the Molex connector (orange and gray wires) to the main power harness.

5. Remembering the manner in which the tape was placed around the touchscreen you removed,

place and cut a length of the supplied black poly tape evenly over an entire edge of the touch-
screen and repeat until all 4 edges are covered.

6. Place and cut a longer length of black poly tape around all 4 edges of the screen.

Games with screws securing front of shroud:

•

Replace the bezel in the shroud and secure it with the 8 screws. See Figures 10 and 16.

Games with bolts securing front of shroud:

•

Replace the shroud and small prize assembly, then secure the front of the shroud
with the 4 nuts and bolts removed earlier.

•

Slide the monitor back into position and secure it with the hardware removed earlier
(see Figures 12-14 for hardware locations).

•

Replace the 4 screws (2 per side) fastening the sides of the shroud to the game.
See Figure 7.

•

Replace the cable clamp fastening the small prize assembly light wiring to the moni-
tor frame. See Figure 8.

8. Replace the cap and large prize assembly, then replace the 8 nuts and bolts fastening the prize

assembly to the game. Then replace the 2 nuts and bolts fastening the cap to the game and
plug in the fluorescent light. See Figure 7.

9. Replace and lock the upper rear door.

10. Plug in and turn on the game.

Hard Drive Removal

1. Turn off and unplug the game.

2. Unlock and open the bottom door.

3. Remove the 4 screws fastening the electronics box cover and carefully remove the cover.

See Figure 1.

4. Using Figure 2, locate the hard drive behind the I/O board. Remove the 4 screws and any

connectors securing the I/O board to the hard drive assembly.

5. Remove the 5 shoulder washers securing the hard drive assembly to the electronics box, then

remove the assembly until you’re able to disconnect the hard drive power connector and hard
drive ribbon cable. See Figure 2.

6. Remove the 4 screws fastening the hard drive to the mounting plate. See Figure 3.

7. Slide the hard drive out of the mounting plate.

Hard Drive Installation

1. Slide the new hard drive into the mounting plate and secure with the 4 screws.

2. Using the existing hardware, re-secure the I/O board to the hard drive mounting plate. Recon-

nect any necessary connectors.

3. Reconnect the power connector and ribbon cable to the hard drive, then slide the hard drive

assembly into place in the electronics box. Tighten the 5 shoulder washers to secure. See
Figure 2.

4. Replace the electronics box cover and fasten it with the 4 screws. See Figure 1.

5. Close and lock the bottom door.

6. Plug in and turn on the game.

Motherboard Removal

1. Turn off and unplug the game.

2. Unlock and open the bottom door.

3. Remove the 4 screws securing the electronics box cover. Carefully remove the cover (see

Figure 1).

4. Disconnect all connections to the motherboard, as well as any other harnesses that may

interfere with removal of the board.

5. Remove the 6 screws (3 top and 3 bottom) fastening the edge of the motherboard to the inside

of the electronics box (see Figure 4), then carefully lift the motherboard out of the game and
insert the board into an anti-static bag for storage.

NOTE: Be sure to read the Motherboard

Handling Precautions before handling the board.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Megatouch Money Shoot

Troubleshooting Information - Removal/Installation of Major Assemblies -

Megatouch Money Shoot

Megatouch FORCE Technical Reference Manual

Motherboard Installation

1. Place the new motherboard in the electronics box and refasten the 6 screws (3 top and 3

bottom) securing it to the inside of the box.

See Figure 4.

2. Reconnect all connections to the motherboard, as well as any harnesses that were discon-

nected earlier.

3. Replace the electronics box cover and fasten it with the 4 screws. See Figure 1.

4. Close and lock the bottom door.

5. Plug in and turn on the game.

Power Supply Removal

1. Turn off and unplug the game.

2. Unlock and open the bottom door.

3. Remove the 4 screws securing the electronics box cover. See Figure 1. Carefully remove the

cover.

4. Remove the 4 shoulder washers (2 on the left interior wall and 2 on the floor of the electronics

box) securing the power supply assembly to the game. See Figure 5.

5. Disconnect all connections to the main power supply harness.

6. Remove the power supply.

Power Supply Installation

NOTE: Before securing the power supply assembly, make sure the ground wire is
secured around the left rear pem stud.

Install the new power supply assembly in the game

in the same manner as the old power supply. Fasten with the existing hardware. See Figure 5.

2. Reconnect all connections to the main power supply harness.

3. Plug the IEC connector into the new power supply.

4. Replace the electronics box cover and fasten it with the 4 screws. See Figure 1.

5. Close and lock the bottom door.

6. Plug in and turn on the game.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Money Shoot (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

Megatouch Money Shoot

Megatouch FORCE Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Money Shoot (cont’d)

Monitor Removal

1. Turn off and unplug the game.

2. Unlock and open the top bezel

3. Use dental floss to carefully cut the foam tape holding the touchscreen to the monitor until

you are able to completely remove the screen. Once the touchscreen is completely free
from the monitor, remove any residual foam tape from the monitor with denatured alcohol.
You will need to place the touchscreen on a stable surface until it is installed on the new
monitor.

4. Remove the 2 screws securing the monitor mounting bracket to the game. See Figure 7.

5. Carefully shifting the monitor mounting bracket on the pegs (if necessary), remove the

following connections behind the monitor (see Figure 8):

VGA monitor connector (gray cord),

Power connector and ground screw,

Monitor control board connector,

Power cable connector (black and yellow wire).

6. Slide the monitor assembly off the bezel and put aside.

7. Unlock and open the monitor bezel.

8. If you will be reusing the existing touchscreen, remove the 2 screws fastening the

touchscreen controller to back of the monitor bezel (see Figure 6) and disconnect the cable
from the underside of the controller. Locate and disconnect the Molex connector (orange
and gray wires). See Figure 6.

If you will not be reusing the existing touchscreen, remove the cable clamps securing the
touchscreen cable and the touchscreen power harness. Next, remove the screws fastening
the touchscreen controller (see Figure 6) to the game and disconnect the cable from the
underside of the controller. Locate and disconnect the Molex connector (orange and gray
wires). See Figure 6.

9. Return to the monitor assembly and remove the 4 corner screws securing the monitor to the

bracket. See Figure 7. Remove the monitor.

10. Close and lock the monitor bezel.

Troubleshooting Information - Removal/Installation of Major Assemblies -

Megatouch Money Shoot

Megatouch FORCE Technical Reference Manual

Monitor Installation

1. Attach the new monitor to the monitor mounting bracket with the 4 screws.

2. If your replacement monitor already has a touchscreen, go to Step 3.

If you are using the original touchscreen, clean the glass on the new LCD monitor with the
supplied alcohol wipe, then cut pieces of the supplied ½” foam tape long enough to cover
each edge of the monitor without overlapping. After the tape is in place on the monitor, peel
off the packing. Carefully place the touchscreen over the monitor in the same manner it was
attached to the old monitor, making sure the screen is properly and evenly aligned over the
glass, then connect to the LCD panel. Clean the front of the touchscreen with the supplied
alcohol wipe once it is in place.

3. Open the top bezel, then slide the monitor assembly onto the 4 pegs. Reattach the 2

screws securing the monitor assembly to the monitor bezel.

4. Reconnect the following connections behind the monitor (see Figure 8). Make sure to

preperly dress the wires so they remain secured. Unlock and open the monitor bezel if
necessary:

VGA monitor connector (gray cord),

Power connector and ground screw,

Monitor control board wire connector, and

Power cable connector (black and yellow wire).

5. If you are reusing the existing touchscreen, reconnect the touchscreen cable underneath the

touchscreen controller and secure the controller with the existing 2 screws. Also connect
the Molex connector (orange and gray wires) to the main power harness. Make sure to
preperly dress the wires so they remain secured.. See Figure 6.

If you are not be reusing the existing touchscreen, install the new touchscreen controller with
the 2 screws. Connect the molex connector, touchscreen controller cable, and the touchscreen
power harness. Make sure to preperly dress the wires so they remain secured. See Figure 6.

6. Close and lock the monitor and top bezels.

7. Plug in and turn on the game.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Money Shoot (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

Megatouch Money Shoot

Megatouch FORCE Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Money Shoot (cont’d)

Touchscreen Removal

1. Turn off and unplug the game.

2. Unlock and open the top and monitor bezels.

3. Cut the tie wraps securing the touchscreen cable and the touchscreen power harness, then

remove the 2 screws fastening the touchscreen controller (see Figure 6) to the game and
disconnect the cable from the back of the controller. Locate and disconnect the Molex connec-
tor (orange and gray wires) running from the touchscreen controller cable to the main power
harness, and also disconnect the ground screw. See Figure 6.

4. Close and lock the monitor bezel.

5. Use dental floss to carefully cut the foam tape holding the touchscreen to the monitor until you

are able to completely remove the screen. Once the touchscreen is completely free from the
monitor, remove any residual foam tape from the monitor with denatured alcohol.

Touchscreen Installation

1. Clean the glass on the reverse side of the new touchscreen with the supplied alcohol wipe,

then cut pieces of the supplied 1/2" foam tape long enough to cover each edge of the monitor
without overlapping. After the tape is in place on the monitor, peel off the backing. Carefully
place the touchscreen over the monitor in the same manner it was attached to the old monitor,
making sure the screen is properly and evenly aligned over the glass. Clean the front of the
touchscreen with the supplied alcohol wipe once it is in place.

2. Unlock and open the top and monitor bezels.

3. Reconnect the touchscreen cable underneath the touchscreen controller and secure the con-

troller with the existing hardware. Also connect the Molex connector (orange and gray wires) to
the main power harness (after routing the wires through the cable clamps). See Figure 6.

4. Close and lock the monitor bezel.

5. Plug in and turn on the game.

6. When the game is finished booting, press the CALIBRATE button on the monitor control board.

7. Close and lock the top bezel, then calibrate the touchscreen.

Troubleshooting Information - Removal/Installation of Major Assemblies -

Megatouch Money Shoot

Megatouch FORCE Technical Reference Manual

Top Bezel Removal

1. Turn off and unplug the game.

2. Unlock and open the top bezel

3. Remove the 6 hexnuts and screws securing the bracket to the back of the game (includ-

ing the two screws holding the small silver bracket). See Figure 9.

4. Go to Step 5 if you are not replacing the top bezel hinge.

Lift the monitor bezel, and remove the 6 hexnuts and screws securing the exterior
bracket to the game (see Figure 10). Remove the bracket.

5. Close the monitor bezel. Locate the yellow rubber coated brackets. On the left and right

sides, remove the hexnut, spring, spacer, and screw securing the top bezel to the
bracket. See Figure 9.

6. Lift and remove the top bezel.

Top Bezel Installation

1. Go to Step 2 if you are not replacing the top bezel hinge.

Place the new bracket in the correct position. See Figure 11.

2. Use the 6 hexnuts and screws to secure the exterior bracket to the game in the monitor
bezel section. See Figure 10.

3. Close and lock the monitor bezel.

4. Replace the hexnut, spring, spacer and screw securing the top bezel to the side brack-

ets on the left and right sides. See Figure 9.

5. Replace the 6 hexnuts and screws securing the bracket to the back of the game (includ-

ing the silver bracket and 2 screws). See Figure 10.

6. Close and lock the top bezel.

7. Plug in and turn on the game.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES

Removal/Installation of Major Assemblies -

Money Shoot (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

Megatouch Money Shoot

Megatouch FORCE Technical Reference Manual

Troubleshooting Information - DIP Switch Settings in FORCE Games

Megatouch FORCE Technical Reference Manual

DIP SWITCH SETTINGS IN FORCE GAMES

The following tables provide information on the functionality of the hard DIP switches in FORCE
games. Make sure to read the information in the “Notes” column to determine what is affected
when performing these functions. After performing any DIP switch function, make sure to follow the
instructions on the screen. In most cases, you will be instructed to reset the DIP switch in order to
reboot the game. If you fail to reset the DIP switch before rebooting, it could result in corruption of
the hard drive.

NOTE:

In FORCE 2005 and Jade software, the DIP switch functionality is built into the software.

To access the DIP switches through the software: Turn off the game. Set DIP switch 1 to the
closed position. Turn power on. When the message

Please reset DIP 1 to proceed

appears,

reset DIP 1 to the open position. The Merit diagnostics page will appear. Touch

for information on

DIP switch functionality. Touch the specific DIP switch to activate it. Touch

to exit.

FORCE 2003 / MAXX Ruby and greater

DIP# Function

Usage/Notes

8 Motherboard

configuration &
checksum test

•

Configures the CMOS settings on the motherboard to Merit
specifications and checks the files on the hard drive.

A checksum test should be performed when the game is locking up or
rebooting. If the test fails, the program should be reloaded onto the hard
drive. After reloading, perform another checksum test. If it fails again, the
hard drive should be replaced.

6 Hardware

configuration

•

Identifies system hardware and configures the motherboard.

A hardware configuration occasionally needs to be performed after a kit is
installed and the touchscreen is not responding to touch or the calibration
is off.

5 & 7

Memory clear for
TournaMAXX™
and
TouchTunes®

•

Clears the login name, password, access phone number, and all call-in
settings for TournaMAXX users.

•

Clears all the loaded albums for TouchTunes users.

•

Clears current books, coin-in, high scores and resets the software
options.

A memory clear should be performed when a game is not able to connect
to TournaMAXX and there is some question about the information in the
Dial-Up Network Screen being correct. After performing a memory clear,
TournaMAXX setup information must be re-entered, and an

Update From

Server

should be performed.

NOTE: TournaMAXX games must perform an Update From Server
BEFORE performing a memory clear.

4 & 7

Complete
memory clear

•

Clears ALL memory on hard drive including the TournaMAXX player
database, TournaMAXX settings, advertising screens, bookkeeping,
high scores, coin-in, options, etc. It resets the game to the factory
defaults. It also marks bad sectors on hard drive.

A complete memory clear should only be performed when the game is
locking up or resetting and it has passed the checksum test. After
performing a memory clear, the player database should be reloaded,
TournaMAXX setup information must be re-entered, and an

Update From

Server

should be performed.

NOTE: TournaMAXX games must perform an Update From Server
BEFORE performing a complete memory clear.

3 Watchdog

Timer

(EVO, Elite Edge,
Fusion and
Money Shoot
games)

•

When the watchdog timer is enabled, it will reboot the machine within 2
minutes of a failure, allowing the game to automatically reset itself if a
problem arises.

Troubleshooting Information - Troubleshooting Guide

Megatouch FORCE Technical Reference Manual

ROBLEM

ORRECTIVE

CTION

•

no power

•

bill acceptor motor does
not run

•

no flash on the monitor
screen

•

no cooling fans
operating

•

no output from power
supply

•

Check that the power cord is connected to a “live” outlet.

•

Check that the power switch is on.

•

Check that the power cord is connected to the game power supply.

•

Check that the power supply’s voltage select switch is set to the proper voltage.

•

Check the harness connections to the on/off switch and circuit breaker.

•

Check the circuit breaker for an “open”.

•

Check the A/C harness connection to the power supply.

•

Check the line cord.

•

no video

•

no cooling fan operation

•

screen is blank

•

no A/C power to the
monitor and bill
acceptor

•

no output from power
supply

•

Check the power on jumper wire located on the motherboard. It should connect
J2 to pin 21 of Panel 1. If this jumper wire is missing or not connected between
the correct pins, it may prevent the power supply from turning on. For more
information, see Tech Note 52.

•

Check the D/C harness connection to the motherboard.

•

Check the A/C harness connection to the power supply.

•

no video

•

cooling fans are working

•

there is a sound when
coins are deposited

Radion, Classic and Upright games:

•

Check the video cable connections to the motherboard and the monitor.

•

Check the AC power harness to the monitor.

•

Radion and FORCE Upright monitors will display a test pattern on the screen
when the video cable is disconnected from the motherboard and the monitor
has power. Disconnect the video cable and if there is no test pattern; replace
the monitor chassis board.

Elite games and Vibe:

•

Check the video cable connections to the motherboard and the LCD display.

•

Check the +12 volt supply voltage to the LCD display (yellow wire +12, black
wire ground)

•

Check the harness connections between the PC boards on the back of the
LCD display.

•

Replace the LCD display.

•

no video

•

constant beeping or a
sequence of beeps

•

The memory card (DIMM) may not be seated properly. Reseat the DIMM or
replace it.

•

no video

•

no sound when coins
are deposited

•

Check all connections to the motherboard.

•

Reseat the DIMM.

•

Replace the motherboard or send it for repair.

•

poor picture quality

•

Adjust Brightness, Contrast, Horizontal, and Vertical controls with monitor
controls.

•

no sound or distorted
sound

•

Check the audio cable from the green audio jack on the motherboard to the
audio amp board.

•

Check the harness from the audio amp board to the speaker.

•

Do a two-button memory clear.

•

coin jam

•

Check the coin mech and coin chute for coins blocking the pathway.

•

Make sure the coin harness is connected between the normally open and
common terminals on the coin switch.

•

Disconnect the bill acceptor and the coin switch one at a time to narrow down
the problem.

•

Check the coin harness for pinched or damaged wires.

•

Disconnect the coin harness from J3 of the I/O board. If the coin jam still
appears, the motherboard will have to be sent for repair.

(NOTE: The Radion cabinets have an optical coin switch.)

•

meter not advancing

•

Check connection at I/O board.

•

Check

wiring

J2 METER

connector on I/O board.

Merit Industries, Inc.

Troubleshooting Guide for

Megatouch FORCE™ Games (FORCE 2002 and earlier)

Troubleshooting Information - Troubleshooting Guide

Megatouch FORCE Technical Reference Manual

ROBLEM

ORRECTIVE

CTION

•

game locks up or resets
while being played or in
the attract mode

•

no movement on the
screen

•

power has to be cycled
off and on to get the
game to function again

•

Check the output voltages from the power supply:

Enhance SFX 1211J

Red wire

+5 volt

Yellow wire

+12 volt

Blue wire

-12 volt

White wire

+5 volt power good

Violet wire

+5 volt VSB

Black wire

ground

Brown wire

+3.3 volt

•

Clean the vents and the fans of any dust and dirt that may interfere with airflow.

•

Clean the CPU cooling fan under the I/O board.

•

Replace the CPU cooling fan if it is not operating properly.

•

Reseat the DIMM on the motherboard.

•

Clear memory with the following procedure:

•

Turn off the game.

•

Press and hold the “Setup” and “Calibrate” buttons.

•

Turn the game on and keep holding the buttons until the screen displays
“TWO BUTTON CLEAR DETECTED RELEASE BUTTONS”. This should
take about 30 seconds.

•

Release the buttons. This will clear high scores, clear the books and reset
options, and reset the game menu and coin menu to their factory settings.

•

Perform a checksum test on the hard drive:

•

Turn off the game.

•

Turn on DS1 position 8 on the I/O board.

•

Turn on the game. The test will take about 20 minutes.

•

A failed test will lock up and display “CHECKSUM ERROR” on the screen.

•

A passed test will display “CHECKSUM OK” then continue to the attract
screens mode.

•

game locks up with
“invalid key for version
PG3002 – V XXXX”

•

Check the program number on the security key. It should be compatible with
the program on the hard drive.

•

Check the contacts on the security key socket. Lift up on the contact on the
bottom of the socket and make sure there is a good connection to the base of
the security key.

•

Check the USB cable that connects the I/O board to the motherboard.

•

Check jumpers JP5 and JP6 on the I/O board. The USB cable can be
connected to two connectors on the I/O board (J5A and J5B). The position of
the shunts on jumpers JP5 and JP6 will enable either J5A or J5B. The shunts
should be positioned towards the connector where the USB cable is connected.
For more information, see Tech Note 55.

•

Try another security key with the same program number or test the security key
in another game with the same program version.

•

“INVALID KEY”
message while
downloading software to
the hard drive

•

If the security key was replaced before the download:

The motherboard did not boot from the CD-ROM drive.
Check that the CD-ROM drive is set as master.
Check the ribbon cable connections between the CD-ROM drive and the
motherboard.
Try another CD ROM drive.

•

If the security key was replaced after the download:

See the “Invalid Key” section above.

Merit Industries, Inc.

Troubleshooting Guide for

Megatouch FORCE™ Games (FORCE 2002 and earlier)

Troubleshooting Information - Troubleshooting Guide

Megatouch FORCE Technical Reference Manual

ROBLEM

ORRECTIVE

CTION

•

"DISK BOOT FAILURE"

This message indicates the motherboard is not receiving data from the hard drive
and has locked up.

•

Check the IDE ribbon cable connections to the motherboard and hard drive.

•

Check the power to the hard drive. It should have +5 volts, +12 volts, and
ground.

•

Move the hard drive IDE cable to the secondary IDE port on the motherboard
to test the board. If the game does not lock up, there is a motherboard failure
and the board should be sent for repair. The game will work with the IDE cable
in the secondary IDE port, but the Head 2 Head games will be missing and the
screen will say “Emerald” instead of “FORCE”.

•

“QUANTUM FIREBALL,
SMART FAILURE
DETECTED, BACK UP
HARD DRIVE”

•

The self-diagnostics on the hard drive has detected an error. The hard drive will
have to be replaced.

•

“ERROR READING
DRIVE C”

This message can be caused by the hard drive or in some program versions, a coin
jam while the game is turned on.

•

Turn the game off.

•

Locate DS 1, position 8 and turn it on.

•

Turn on power to the cabinet. This will start the hard drive checksum test,
which should take about 20 minutes to complete.

•

When the hard drive passes the test it will display a “CHECKSUM GOOD”
message and continue to boot up into the game attract screens. This
indicates a coin jam.

•

When the hard drive fails the test, the game will lock up with a
“CHECKSUM ERROR” message, which will stay on the screen until the
power is turned off. In this case, the hard drive will have to be replaced.

•

“CRITICAL ERROR
ABORT RETRY FAIL” –
or “BAD COMMAND OR
FILE NAME” error

•

Try reloading the program onto the hard drive with a set of update CD’s
compatible with the security key. If it will not accept the download, replace the
hard drive.

•

the screen does not
display FORCE it has
MAXX, and the H2H
category is missing

•

When the game is turned on, it will check the type of touchscreen controller,
motherboard and hard drive. If one of these does not match with FORCE
hardware, the game will power up and display “MAXX” on the screen and it will
not have the H2H category.

•

The IDE cable from the hard drive must be connected to the primary IDE port
on the motherboard. When it is connected to the secondary IDE port, the
screen will display “MAXX” and not have the H2H category.

•

game will not download
CD

•

Make sure the CD is installed correctly, with the logo facing up.

•

Check for scratches or a defective disc.

•

Try a different set of CDs.

•

If you’re downloading a CD set, make sure each disc is of the same revision.

Merit Industries, Inc.

Troubleshooting Guide for

Megatouch FORCE™ Games (FORCE 2002 and earlier)

Troubleshooting Information - Troubleshooting Guide

Megatouch FORCE Technical Reference Manual

Merit Industries, Inc.

Troubleshooting Guide for

Megatouch FORCE™ Games (FORCE 2003 and later)

ROBLEM

ORRECTIVE

CTION

•

no power

•

bill acceptor motor
does not run

•

no flash on the
monitor screen

•

no cooling fans
operating

•

no output from
power supply

•

Check that the power cord is connected to a “live” outlet.

•

Check that the power switch is on.

•

Check that the power cord is connected to the game power supply.

•

Check that the power supply’s voltage select switch is set to the proper
voltage.

•

Check the harness connections to the on/off switch and circuit breaker.

•

Check the circuit breaker for an “open”.

•

Check the A/C harness connection to the power supply.

•

Check the line cord.

•

no video

•

no cooling fan
operation

•

screen is blank

•

A/C power to the
monitor and bill
acceptor

•

no output from
power supply

•

Check the power on jumper wire located on the motherboard. It should
connect J2 to pin 21 of Panel 1. If this jumper wire is missing or not
connected between the correct pins, it may prevent the power supply from
turning on. For more information, see Tech Note 52.

•

Check the D/C harness connection to the motherboard.

•

Check the A/C harness connection to the power supply.

•

no video

•

cooling fans are
working

•

there is a sound
when coins are
deposited

Radion, Classic and Upright games:

•

Check the video cable connections to the motherboard and the monitor.

•

Check the AC power harness to the monitor.

•

Radion and FORCE Upright monitors will display a test pattern on the
screen when the video cable is disconnected from the motherboard and
the monitor has power. Disconnect the video cable and if there is no test
pattern; replace the monitor chassis board.

Elite games and Vibe:

•

Check the video cable connections to the motherboard and the LCD
display.

•

Check the +12 volt supply voltage to the LCD display (yellow wire +12,
black wire ground)

•

Check the harness connections between the PC boards on the back of the
LCD display.

•

Replace the LCD display.

•

no video

•

constant beeping or
a sequence of beeps

•

The memory card (DIMM) may not be seated properly. Reseat the DIMM
or replace it.

•

no video

•

no sound when
coins are deposited

•

Check all connections to the motherboard.

•

Reseat the DIMM.

•

Replace the motherboard or send it for repair.

•

poor picture quality

•

Adjust Brightness, Contrast, Horizontal, and Vertical controls with monitor
controls.

•

coin jam

•

Check the coin mech and coin chute for coins blocking the pathway.

•

Make sure the coin harness is connected between the normally open and
common terminals on the coin switch.

•

Disconnect the bill acceptor and the coin switch one at a time to narrow
down the problem.

•

Check the coin harness for pinched or damaged wires.

•

Disconnect the coin harness from J1, J3, J7, and J8 of the I/O board. If the
coin jam still appears, the I/O board will have to be sent for repair.

(NOTE: The Radion cabinets have an optical coin switch.)

•

meter not advancing

•

Check connection at I/O board.

•

Check wiring at

J2 METER

connector on I/O board.

Troubleshooting Information - Troubleshooting Guide

Megatouch FORCE Technical Reference Manual

Merit Industries, Inc.

Troubleshooting Guide for

Megatouch FORCE™ Games (FORCE 2003 and later)

ROBLEM

ORRECTIVE

CTION

•

game locks up or
resets while being
played or in the attract
mode

•

no movement on the
screen

•

power has to be
cycled off and on to
get the game to
function again

•

Check the output voltages from the power supply:

Enhance SFX 1211J

Red wire +5 volt
Yellow wire

+12 volt

Blue wire  -12 volt
White wire  +5 volt power good
Violet wire  +5 volt VSB
Black wire  ground
Brown wire +3.3 volt

•

Clean the vents and the fans of any dust and dirt that may interfere
with airflow.

•

Clean the CPU cooling fan on the motherboard.

•

Replace the CPU cooling fan if it is not operating properly.

•

Reseat the DIMM on the motherboard.

•

Clear memory with the following procedure:

•

Turn off the game.

•

Press and hold the “Setup” and “Calibrate” buttons.

•

Turn the game on and keep holding the buttons until the screen
displays “TWO BUTTON CLEAR DETECTED RELEASE
BUTTONS”. This should take about 30 seconds.

•

Release the buttons. This will clear high scores, clear the books
and reset options, and reset the game menu and coin menu to
their factory settings.

•

Perform a checksum test on the hard drive:

•

Turn off the game.

•

Turn on DIP switch 8 on the I/O board.

•

Turn on the game. The test will take about 10 minutes.

•

A failure will cause the test to stop.

•

A passed test will display “DRIVE CHECKSUM
COMPLETE RESET ALL DIP SWITCHES TO REBOOT
MACHINE”.

•

With power on, turn off DIP switch 8.

•

game locks up with
“invalid key for
version PG3002 – V
XXXX”

•

Check the program number on the security key. It should be
compatible with the program on the hard drive.

•

Check the contacts on the security key socket. Lift up on the contact
on the bottom of the socket and make sure there is a good connection
to the base of the security key.

•

Check the USB cable that connects the I/O board to the motherboard.

•

Check jumpers JP5 and JP6 on the I/O board. The USB cable can be
connected to two connectors on the I/O board (J5A and J5B). The
position of the shunts on jumpers JP5 and JP6 will enable either J5A
or J5B. The shunts should be positioned towards the connector where
the USB cable is connected. For more information, see Tech Note 55.

•

Try another security key with the same program number or test the
security key in another game with the same program version.

•

“INVALID KEY”
message while
downloading software
to the hard drive

•

If the security key was replaced before the download:

•

The motherboard did not boot from the CD-ROM drive.

•

Check that the CD-ROM drive is set as master.

•

Check the ribbon cable connections between the CD-ROM drive and
the motherboard.

•

Try another CD-ROM drive or another set of CDs.

Troubleshooting Information - Troubleshooting Guide

Megatouch FORCE Technical Reference Manual

Merit Industries, Inc.

Troubleshooting Guide for

Megatouch FORCE™ Games (FORCE 2003 and later)

ROBLEM

ORRECTIVE

CTION

•

the screen
displays MAXX
and not FORCE,
and the H2H
category is
missing

When the game is turned on, it will check the type of touchscreen
controller, motherboard and hard drive. If one of these does not match
with FORCE hardware, the game will power up and display “MAXX” on
the screen and it will not have the H2H category.

•

Make sure the game is only using FORCE hardware.

•

game will not
download CD

•

Make sure the CD is installed correctly, with the logo facing up.

•

Check for scratches or a defective CD.

•

Try a different CD-ROM drive or another set of CDs.

•

If you’re downloading a CD set, make sure each CD is of the same
revision.

•

"ERROR
READING DRIVE
C"

•

This message can be caused by the hard drive or in some
program versions, a coin jam while the game is turned on.

Turn the game off.

Locate DS 1, position 8 and turn it on.

Turn on power to the cabinet. This will start the
hard drive checksum test, which should take about
20 minutes to complete.

When the hard drive passes the test it will display
a "CHECKSUM GOOD" message and continue to
boot up into the game attract screens. This
indicates a coin jam.

When the hard drive fails the test, the game will
lock up with a "CHECKSUM ERROR" message,
which will stay on the screen until the power is
turned off. In this case, the hard drive will have to
be replaced.

•

"DISK BOOT
FAILURE"

This message indicates the motherboard is not receiving data from the
hard drive and has locked up.

•

Check the IDE ribbon cable connections to the motherboard and
hard drive.

•

Check the power to the hard drive. It should have +5 volts, +12
volts, and ground.

•

“QUANTUM
FIREBALL,
SMART FAILURE
DETECTED,
BACK UP HARD
DRIVE”

The self-diagnostics on the hard drive has detected an error.

•

The hard drive will have to be replaced.

•

“CRITICAL
ERROR ABORT
RETRY FAIL” or
“BAD COMMAND
OR FILE NAME”
error

•

Try reloading the program onto the hard drive with a different set of
update CD’s compatible with the security key. If it will not accept the
download, try another CD-ROM drive. If it still does not work,
replace the hard drive.

Merit Industries, Inc.

TouchTunes® Troubleshooting Guide

Troubleshooting Information - Troubleshooting Guide

Megatouch FORCE Technical Reference Manual

ROBLEM

OSSIBLE

AUSE

ORRECTIVE

CTION

•

TouchTunes®
button does not
appear in the Main
Menu and Touch-
Tunes® icon does
not appear in the
Game Menu.

•

The Single Board Computer
(SBC) is not properly
connected to the game.

•

The SBC experienced an error
(a “Check Diagnostics”
message will appear a the
bottom of the screen).

•

A song did not finish
downloading.

•

Make sure the cable between the game
and the Ethernet hub is properly
connected.

•

MegaTunes™ only:

•

In MAXX™ games without Unicorn
boards, make sure you properly followed
the steps outlined in the MegaLink® kit
when linking the game to the
MegaTunes™ unit.

•

Enter the Diagnostic screen from the
Jukebox Operator Menu and follow the
on-screen instructions.

•

Reboot the machine.

If the problem persists, call TouchTunes
Technical Support: 1-888-711-JUKE.

•

unit cannot connect
to the server

•

The unit failed to communicate
with the TouchTunes server.

•

A period of inactivity has
caused the unit to lose
communication with the server.

•

There is a problem with the
phone line.

•

Follow these steps until the problem is
solved:
1. Activate the Jukebox Operator menu.
2. Touch Diagnostic to see the results of

the last call to the server. If you see an
error message, follow the instructions
on the screen. The problem could
simply be a matter of the unit needing
to reconnect with the server via the
CALL NOW button.

3. Check that the phone line is functioning

properly.

If the problem persists, call TouchTunes
Technical Support: 1-888-711-JUKE.

•

“ERROR: Modem
rejected
initialization string.”

•

The modem could not be
initialized because it rejected
the initialization string.

•

Call TouchTunes Technical Support: 1-
888-711-JUKE.

•

“ERROR: Modem is
not responding.”

•

The modem could not be
initialized because it is not
responding. This may be
caused by one of the following:

The modem card is not
properly seated.

The modem card is defective.

•

Follow these steps to re-seat the modem
card in the SBC:
1. Remove the screw that holds the card

in place.

2. Place the connector on the bottom of

the card in line with its socket on the
motherboard.

3. Place a thumb on the front and back of

the card and press down firmly on the
card until it is securely seated in its
socket.

4. Replace the screw.

If the problem persists, call TouchTunes
Technical Support: 1-888-711-JUKE.

•

“ERROR:
Authentication
failed.”

•

Authentication failed.

•

The jukebox will automatically retry to
authenticate.

If the problem persists, call TouchTunes
Technical Support: 1-888-711-JUKE.

ROBLEM

OSSIBLE

AUSE

ORRECTIVE

CTION

•

“ERROR: Call
failed: No dial tone.
The call could not
be completed
because the
modem failed to
detect a dial tone.”

•

The phone line is not working.

•

Another device already using
the phone line.

•

Phone line has voice mail or
other service that interferes
with the dial tone.

•

The calling prefix that disables
call waiting or other service
does not contain a long
enough pause to permit return
of the dial tone.

•

There is a bad phone
connection between the
modem card and telephone
wall outlet.

•

The modem is defective.

•

Verify that the jukebox is connected to the
phone line.

•

Connect a phone to the telephone wall
outlet and make sure the phone line is
working properly.

•

If the line has voice mail or other services
that interfere with the dial tone, make sure
the proper dialing prefix is being used to
temporarily disable the service.

•

Check the phone connections between the
modem card and wall outlet.

•

Make sure toll-free numbers are not blocked
at the location.

If the problem persists, call TouchTunes
Technical Support: 1-888-711-JUKE.

•

“ERROR: Call
failed: The modem
detected a busy
signal.”

The call could not be completed
because the modem detected a
busy signal. This may be caused
by one of the following:

•

The ISP or the TouchTunes
server is busy.

•

The phone line in use by
shared location phone.

•

The wrong dialing prefix was
used.

Follow these steps until the problem is solved:
1. Wait a few minutes and then try the

connection again. If the problem persists,
continue with step2.

2. Connect a phone to the telephone wall

outlet and make sure the phone line is
working properly and not being used by a
shared phone.

3. Check that the dialing prefix entered for the

location is correct.

If the problem persists, call TouchTunes
Technical Support: 1-888-711-JUKE.

•

“ERROR: Call
failed: A modem
did not answer at
the dialed
number.”

The call could not be completed
because a modem did not answer
the call. This may be caused by
one of the following:

•

The modem dialed the wrong
number (bad dialing prefix).

•

The ISP server or TouchTunes
server is not working.

Follow these steps until the problem is solved:
1. Wait a few minutes and then try the

connection again. If the problem persists,
continue with step 2.

2. Check that the dialing prefix entered for the

location is correct.

If the problem persists, call TouchTunes
Technical Support: 1-888-711-JUKE.

Troubleshooting Information - Troubleshooting Guide

Megatouch FORCE Technical Reference Manual

Merit Industries, Inc.

TouchTunes® Troubleshooting Guide

Troubleshooting Information - Troubleshooting Guide

Megatouch FORCE Technical Reference Manual

ROBLEM

OSSIBLE

AUSE

ORRECTIVE

CTION

•

“ERROR: Call

failed: PPP
connection
failure.”

•

The jukebox failed to

establish a PPP connection
with the TouchTunes server
or your ISP. The most
frequent cause of this is that
the ISP is down.

•

Keep trying the connection again until it is

successful.

•

If the problem persists, call TouchTunes

Technical Support: 1-888-711-JUKE.

•

no sound

•

zone 1 and 2 (if applicable)

volume levels are both at
zero

•

amplifier fault protection

circuit was tripped

•

speaker wiring is loose or

damaged

•

amplifier cables are loose or

not connected

•

amplifier or speakers are

defective or blown

•

sound card is loose or

defective

•

Make sure the volume has not been turned

down to 0 using the remote or volume
controls on the unit.

•

Try pausing/unpausing the unit with the

remote several times.

•

Verify the Sound Mixer screen settings.

•

Check the connections to the amplifier.

•

Make sure that the amplifier and speakers

are not defective or blown.

•

Reset amplifier fault protection circuit.

•

Re-seat the sound card.

•

If the problem persists, call TouchTunes

Technical Support: 1-888-711-JUKE.

•

volume

automatically
goes to maximum
or minimum

•

backup volume control

buttons on the unit are
pushed in or jammed in
place

•

there is interference from

another RF-based remote

•

Check the condition of the backup volume

control buttons.

•

Check to see if another remote may be

causing the problem.

•

If the problem persists, call TouchTunes

Technical Support: 1-888-711-JUKE.

•

one or more

songs in the
purchase list
failed to
download

•

The purchase list has more

songs in it than the download
limit allows per night.
Generally, seven songs will
download each time the unit
calls the server. This can be
overridden by TouchTunes
personnel if required.

•

Communications with the

TouchTunes server was slow
due to noisy phone lines,
interrupted communications,
or Internet congestion.

•

The unit failed to

communicate with the
TouchTunes server.

•

Follow these steps until the problem is

solved:

1. Activate the Jukebox Operator menu.
2. Touch Diagnostic to see the results of the

last call to the server. If you see an error
message, follow the instructions on the
screen.

3. If no errors exist and you did not get your

full download of seven songs:

•

a noisy phone line (internal or external)
caused a communica-tion problem, and
therefore only a few songs could be
downloaded in the allowed time. If noisy
phone lines are a chronic problem, you
may want to increase the size of the
calling window available to the unit every
night.

•

a person or device tried to use the phone
while the unit was calling out. If this
happens repeatedly, it can reduce the
number of songs the unit is able to
download.

•

the Internet is congested. The unit
connects to the server via an Internet
connection. Sometimes, traffic on the
Internet is backed up, resulting in very
slow throughput. This can significantly
reduce the number of songs the unit can
download in one night.

If the problem persists, call TouchTunes
Technical Support: 1-800-711-JUKE.

Merit Industries, Inc.

TouchTunes® Troubleshooting Guide

ROBLEM

OSSIBLE

AUSE

ORRECTIVE

CTION

•

a song cannot be
added to the
purchase list

•

The unit already has the
maximum number of songs
installed on it (approximately
2,000). Songs in the purchase
list are counted in this total,
since space must be reserved
on the hard drive to receive
them.

•

Delete songs from the unit in order to
create space for songs on the purchase
list.

If the problem persists, call TouchTunes
Technical Support 1-800-711-JUKE.

•

remote control
does not work

•

Support for the remote is not
enabled.

•

The batteries in the remote
control are dead.

•

The switches in the battery
compartment were changed.

Follow these steps until the problem is
solved:

•

Put new batteries into the remote control.

•

Check the System Settings screen and
make sure the REMOTE CONTROL
MODE is ON.

•

Re-learn the remote ID.

If the problem persists, call TouchTunes
Technical Support: 1-888-711-JUKE.

•

no sound when
using microphone

•

The PAUSE button was
pressed on the remote control.

•

The microphone volume limit
is set to 0.

•

The microphone is improperly
connected to the Single Board
Computer.

•

The microphone is defective.

•

The microphone cable is
damaged or defective.

•

Follow these steps until the problem is
solved:

1. Go to the Sound Mixer screen and

make sure that the maximum volume
for the microphone is not limited to 0.

2. Make sure that the microphone is

connected to the MIC IN input on the
Single Board Computer.

3. Verify that the microphone is in

working order and that the cable
between the microphone and Single
Board Computer has not been
severed or damaged.

If the problem persists, call TouchTunes
Technical Support: 1-888-711-JUKE.

•

humming noise
from any speaker
after connecting to
an external audio
device

•

There is a ground loop.

•

Ground loops can occur when there is
more than one path to the electrical
ground. A quick way to solve the problem
is to install a ground loop isolator on the
audio cable that connects the unit to the
external audio device.

If the problem persists, call TouchTunes
Technical Support: 1-888-711-JUKE.

Troubleshooting Information - Troubleshooting Guide

Megatouch FORCE Technical Reference Manual

Merit Industries, Inc.

TouchTunes® Troubleshooting Guide

Troubleshooting Information - Mars 2000 Bill Acceptor DIP Switch Settings

Megatouch FORCE Technical Reference Manual

DIP Switch Settings for the Mars 2000 Bill Acceptor

(The DIP switches are located on the side of the bill acceptor)

SETTING

SWITCHES

1 W AY

DIP 1 ON/DIP 2 OFF

2 W AY

DIP 1 OFF/DIP 2 ON

4 W AY

DIP 1 ON/DIP 2 ON

HIGH ACCEPTANCE

DIP 3 OFF

HIGH SECURITY

DIP 3 ON

*$1

DIP 4 ON=ACCEPT/OFF=REJECT

*$2

DIP 5 ON=ACCEPT/OFF=REJECT

*$5

DIP 6 ON=ACCEPT/OFF=REJECT

1 PULSE PER DOLLAR

DIP 7 OFF

*4 PULSES PER DOLLAR

DIP 7 ON

ALW AYS ENABLE

DIP 8 OFF

HARNESS ENABLE

DIP 8 ON

* Recommended factory settings allow for acceptance of $1, $2, and $5 bills at 4 pulses
per dollar.

Setting the Coin-In Menu

Settings for the bill acceptor are controlled by the settings for Electronic Mech 2 (2E) in the
Coin-In Menu screen.

To set the Coin-In Menu to provide a bonus credit for the use of a dollar, set the number of
coins (for Electronic Mech 2) to

and set the number of credits to

. This will provide 5

credits for each dollar entered.

M eter Pulses

can be set to

to record the amount of

“coins” in the cashbox, or it can be set to

to record the number of credits played,

depending on your individual need. An illustration of the coin-in menu set to offer 5 credits
for a dollar, with the meter counting coins, is shown below.

See your owner’s manual for complete operating instructions for the Coin-In Menu.

CREDITS

COIN

INPUT

COINS

METER PULSES

WIRE COLOR

USE

BROWN

+3.3 VDC

BROWN

+3.3 VDC

BLACK

GND

RED

+5 VDC

BLACK

GND

RED

+5 VDC

BLACK

GND

WHITE

PWR GOOD

VIOLET

+5V VSB

YELLOW

+12 VDC

BROWN

+3.3 VDC

BLUE

-12 VDC

BLACK

GND

BLACK

GND

BLACK

GND

BLACK

GND

BLACK

GND

-----

RED

+5 VDC

RED

+5 VDC

FIGURE 2 - REAR VIEW OF CABLE CONNECTOR

Molex Connector (manufacturer part # 39-01-2200)

Molex Pin (manufacturer part # 39-00-0038)

Motherboard - Power Connector

Motherboard - Motherboard Diagrams

Megatouch FORCE FORCE Technical Reference Manual

Motherboard Diagrams (cont’d)

Motherboard - I/O Board Diagrams

Megatouch FORCE FORCE Technical Reference Manual

SA10055-01 - I/O Board Diagrams

(Radion, Classic, Elite, and Combo Jukeboxes and Upright games)

Merit # SA10055-01 I/O Board

FIGURE 3 - I/O BOARD DRAWING

Required Connections

I/O Board Power Connector: to supply power to the I/O board

Electronic Mech Connector: for electronic mech operation

Smiley Bill Acceptor Connector: for Smiley bill acceptor operation

Mechanical Mech/Lockout Connector: for mechanical mech opera-
tion

Meter Connector: for meter operation

Security Key Socket: install security key for game operation

Motherboard: connects I/O board and motherboard, connected at
the factory

METER

SETUP

CALIBRATE

SMILEY

BILL

ACCEPTOR

MECHANICAL
MECH

I/O BOARD
POWER

ELECTRONIC
MECH

JP5/JP6
JUMPER FOR

USB PORT

SECURITY

KEY

J5B

FROM USB PORT

ON MOTHERBOARD

J5A

FROM USB PORT

ON MOTHERBOARD

DETAIL VIEW

JUMPER LOCATION
TO ACTIVATE J5B

DETAIL VIEW

JUMPER LOCATION
TO ACTIVATE J5A

NOTE: The orientation of the jumpers at JP5/JP6 will determine which
USB connector on the I/O board is activated.

Motherboard - I/O Board Diagrams

Megatouch FORCE FORCE Technical Reference Manual

SA10055-01 - I/O Board Diagrams (cont’d)

I/O Board - Meter Connector (J2)

WIRE COLOR

USE

BLACK

COUNTER 1(-) TERMINAL COIN

BLACK

COUNTER 2 (-) TERMINAL TMAXX

BLACK

SETUP HI

BLACK

CALIBRATE HI

YELLOW

+12 VDC

GREEN

GROUND, SETUP/CALIBRATE COMMON

FIGURE 5 - TOP VIEW OF CABLE CONNECTOR

JST Connector (manufacturer part # 06NR-E4K)

WIRE COLOR

USE

WHITE

BILL 1

WHITE

BILL 2

WHITE

BILL 3

WHITE

BILL 4

GREEN

INHIBIT 1 (GND)

GREEN

INHIBIT 2 (GND)

GREEN

INHIBIT 3 (GND)

GREEN

INHIBIT 4 (GND)

BLUE

ESCROW +12 VDC

YELLOW

+12 VDC

GREEN

GROUND

YELLOW

+12 VDC

I/O Board - Smiley Bill Acceptor Connector (J8)

PIN 1

FIGURE 4 - TOP VIEW OF CABLE CONNECTOR

JST Connector (manufacturer part # 12NR-E4K)

Motherboard - I/O Board Diagrams

Megatouch FORCE FORCE Technical Reference Manual

SA10055-01 - I/O Board Diagrams (cont’d)

I/O Board - Mechanical Mech Connector (J3)

WIRE COLOR

USE

-----

YELLOW

+ 12VDC (OUT)

WHITE

COIN 1

RED

+ 5 VDC (OUT)

GREEN

GROUND

GREEN

GROUND

GREEN

GROUND

FIGURE 7 - TOP VIEW OF CABLE CONNECTOR

JST Connector (manufacturer part # 07NR-E4K)

I/O BOARD

BLACK

YELLOW

COIN

COUNTER

0000000

TOURNAMAXX

COUNTER

COUNTER 1

COUNTER 2

SET-UP HI

CALIBRATE HI

12 VDC

GROUND

SET-UP/CALIBRATE

COMMON

(-)

(+)

+ VDC (+12 VDC MAX)

12 VDC (OUT)

GREEN

SET-UP

CALIBRATE

FIGURE 6 - I/O BOARD METER CONNECTOR SCHEMATIC

PIN 1

SA10065-01 - I/O Board Diagrams

(FORCE Fusion and EVO games)

Merit # SA10065-01 I/O Board

Motherboard - I/O Board Diagrams

Megatouch FORCE FORCE Technical Reference Manual

FIGURE 9 - I/O BOARD DRAWING

Required Connections

I/O Board Power Connector: to supply power to the I/O board

Electronic Mech Connector: for electronic mech operation

Smiley Bill Acceptor Connector: for Smiley bill acceptor operation

Mechanical Mech/Lockout Connector: for mechanical mech
operation

Meter Connector: for meter operation

Security Key Socket: install security key for game operation

Motherboard: connects I/O board and motherboard, connected at
the factory

SECURITY

KEY

CALIBRATE

SETUP

USB

CONNECTOR

MECHANICAL MECH

REMOTE SETUP/

CALIB/KEY TO J2
ON OSD BOARD

DIP SWITCH
BANK

POWER

CONNECTOR

ELECTRONIC MECH

J19

METER 2

JP7

(SHUNT REMOVED
FOR IMONEX
COIN MECH)

J8
SMILEY BILL

ACCEPTOR

METER 1

WIRE COLOR

USE

WHITE

BILL 1

WHITE

BILL 2

WHITE

BILL 3

WHITE

BILL 4

GREEN

INHIBIT 1 (GND)

GREEN

INHIBIT 2 (GND)

GREEN

INHIBIT 3 (GND)

GREEN

INHIBIT 4 (GND)

BLUE

ESCROW +12 VDC

YELLOW

+12 VDC

GREEN

GROUND

YELLOW

+12 VDC

I/O Board - Smiley Bill Acceptor Connector (J8)

PIN 1

FIGURE 10 - TOP VIEW OF CABLE CONNECTOR

JST Connector (manufacturer part # 12NR-E4K)

I/O Board Diagrams (cont’d)

Motherboard - I/O Board Diagrams

Megatouch FORCE FORCE Technical Reference Manual

I/O Board - Meter Connector (J2)

WIRE COLOR

USE

BLACK

COUNTER 1(-) TERMINAL COIN

BLACK

COUNTER 2 (-) TERMINAL TMAXX

FIGURE 11 - TOP VIEW OF CABLE CONNECTOR

Molex Connector (manufacturer part # 43645-0200)

PIN 1

Motherboard - I/O Board Diagrams

Megatouch FORCE FORCE Technical Reference Manual

I/O Board - Mechanical Mech Connector (J3)

WIRE COLOR

USE

-----

YELLOW

+ 12VDC (OUT)

WHITE

COIN 1

RED

+ 5 VDC (OUT)

GREEN

GROUND

GREEN

GROUND

GREEN

GROUND

FIGURE 12 - TOP VIEW OF CABLE CONNECTOR

JST Connector (manufacturer part # 07NR-E4K)

PIN 1

FIGURE 13 - TOP VIEW OF CABLE CONNECTOR

JST Connector (manufacturer part # 08NR-E4K)

WIRE COLOR

USE

WHITE

COIN 1

WHITE

COIN 2

WHITE

COIN 3

WHITE

COIN 4

WHITE

COIN 5

WHITE

COIN 6

YELLOW

+12 VDC

GREEN

GROUND

I/O Board - Electronic Mech Connector (J1)

PIN 1

I/O Board Diagrams (cont’d)

Degaussing your Monitor

(Classic, Upright, Megatouch Combo Jukebox, and Radion games only)

If your monitor is displaying “purity problems,” (a display with purity problems will have parts of an all-white

screen affected by blotches of color) the monitor needs to be degaussed using a “degaussing coil.” A de-

gaussing coil is a circular electromagnet used to cancel out any stray magnetic fields that may build up on a

metal object.

All of our monitors have built-in degaussing coils that are automatically activated on power-up. If your game is

experiencing minor purity problems, try powering down the game for 5 minutes and then reapplying power to

activate the degaussing coil. If the problem is not corrected, you will have to use a manual degaussing coil.

Follow the instructions below for degaussing a monitor.

Plug in your degaussing coil.

Hold the coil about three feet from the monitor, press the trigger to activate the magnetic field (for circular-
shaped coils, orient the coil so you see the monitor through the hole in the middle; for wand-shaped coils,
point the wand towards the screen).

Move the coil in a circular motion around the face of the monitor and slowly approach the game.

Continuing to move the coil in a circular motion, slowly back away from the monitor.

5a. CIRCULAR-SHAPED COILS: When you are about three feet away, quickly turn the coil perpendicular to

the monitor and release the trigger.

5b. WAND-SHAPED COILS: When you are about three feet away, point the wand away from the monitor and

release the trigger.

Monitors Information - Degaussing Procedures

Megatouch FORCE Technical Reference Manual

Monitors Information - Monitor Adjustment Procedures

Megatouch FORCE Technical Reference Manual

Monitor Adjustment Procedures

For adjusting the picture on MAXX games, we suggest following the procedures described below. The

vertical/horizontal controls and brightness/contrast controls are located on the monitor control panel that is

Velcroed inside the game. The monitor RGB controls are located on the monitor neck board.

Tatung/Wells Gardner Monitors

For games running software versions prior to Emerald:

Under STRATEGY, select the 11-Ball game.

Adjust the brightness and contrast controls until there is no shadow on the yellow balls and no pixels of the

incorrect color appear on any of the balls. (Adjusting the brightness and contrast can also correct for a lack

of sharpness.)

To adjust the color and screen positioning, use the SETUP button inside the game to bring up the VIDEO
TEST button.

Select VIDEO TEST and bring up the grid screens (the third and fourth screens in the VIDEO TEST). Use
the grid screen to ensure that the game is centered, using the vertical/horizontal controls on the monitor
control board to adjust the screen position and ensure that the game screen correctly fills the monitor screen.

Use the RGB controls on the monitor neck board with the remaining video test screens to adjust screen
color.

Once the necessary adjustments have been made, touch the screen until you bring up the VIDEO TEST
menu again, then exit out of the menu.

For games running Emerald software or a later version:

Under STRATEGY, select the 11-Ball game.

Adjust the brightness and contrast controls until there is no shadow on the yellow balls and no pixels of the

incorrect color appear on any of the balls. (Adjusting the brightness and contrast can also correct for a lack

of sharpness.)

To adjust the color , use the SETUP button inside the game to bring up the VIDEO TEST button.

Select VIDEO TEST and bring up the color test screens, then use the RGB controls on the monitor neck
board to adjust screen color.

Once the necessary adjustments have been made, touch the screen until you bring up the VIDEO TEST
menu again, then exit out of the menu.

To adjust the screen positioning, select NEW GAMES, then Backjammin, then Acey Deucey (Acey Deucey

has the widest playing screen of all the games). Use the vertical/horizontal controls on the monitor control
board to center the screen position and ensure that the game screen correctly fills the monitor screen.

Kortek Flatscreen Monitors

Press any button on the monitor control board (located on the reverse side of the LCD screen) to bring up the
menu screen.

Use the SW2 and SW3 buttons to arrow through the menu and select BASIC SETTINGS with the SW1
button.

Use SW1 to select default or manual settings. Follow the menus on the screen to make manual adjustments.

Exit out of each menu once the necessary adjustments have been made.