manuals/manuals_Support_Center_Vibe_PM0352_10_20Vibe_20manual

Vibe Installation Instructions

Overview ......................................... p. 1

Mounting the Terminal ................ p. 2-20

Mounting the Processor ............ p. 21-26

Connecting the Terminal and
Processor ....................................... p. 27

Linking Games .............................. p. 28

General Care & Maintenance

Screen Calibration .................... p. 29

General Circuit Board Handling
Information ................................ p. 30

Cleaning the Vibe...................... p. 30

Megatouch FORCE Software

Game Name and Score Needed for
Initial Replay ................................... p. 31

Main Menu ...................................... p. 32-33

Credits/Pricing Menu ................... p. 34

Quick Price Setup ..................... p. 34

Coin-In ....................................... p. 35

Coinless Coin Op Menu ............ p. 36-37

Rental Mode .............................. p. 37

Games Menu .................................. p. 37

Game Setup .............................. p. 37-38

Hi Scores Menu ............................... p. 38

View/Clear Hi Scores ................. p. 38

Books Menu ..................................... p. 39

Books Display ............................. p. 39

Cash Settlement .......................... p. 40

System Menu ................................... p. 41

Diagnostics Menu ........................... p. 42

Presentation Menu ......................... p. 43

Operator’s Presentation ............. p. 43

Sales Person’s Presentation ...... p. 43

Operator Ad Screens ................. p. 44

Promotion Menu ............................. p. 44

My Merit ....................................... p. 44-45

Merit Money ................................. p. 45

Promo Credits ............................. p. 45

Megatouch FORCE Hardware

DIP Switch Settings in
FORCE Games .................................. p. 46

Troubleshooting Guide ................. p. 47-48

Replacement Parts List ................. p. 49

Connection Diagrams .................... p. 50-51

Warranty and Software License
Agreements

Warranty ............................................. p. 52

Software License Agreements .......... p. 53-58

Table of Contents

Vibe Installation Instructions

*The installation of the Vibe requires hardware and tools which are not included.

Overview

The Vibe is a custom installation product. It is designed to offer versatility in setting up the

processor and terminal. You can mount the processor and terminal as you see fit. Both

units should be located in an area where the ventilation slots are free from obstruction and

where it will not be damaged by moisture or physical contact. It should be plugged into a

properly grounded outlet (supplying 110 V A/C, 2A, 50-60 Hz or 220 V A/C, 2A, 50-60 Hz)

that is on a separate circuit from any electrical-noise making equipment, such as large

freezers, generators, etc.

NOTE:

Vibe processors in Canada must be mounted on the wall using the processor cover

and terminals must be placed on the bar using the base support.

The terminal and the processor can be mounted without the need for additional mounting

kits. The terminal can be mounted using either recessed wall or surface wall mounting and

the processor can be mounted using standard mounting or it can rest on the rubber feet on

the bottom of the processor. We recommend that the processor be mounted to avoid

damage it could sustain if left unmounted. Templates have been provided with both the

terminal and the processor if these standard mounting options are the mounting options you

have chosen.

The hardware that is supplied with the mounting option you have chosen is only the neces-

sary hardware to mount the terminal or processor to support devices. All other hardware

necessary to mount the components to the wall or other mounting surface will vary depend-

ing on your mounting surface and therefore need to be customer supplied. When mounting

both components, use hardware sufficient to support the weight for your application. (The

processor is 17 pounds, the terminal is 22 pounds for Vibes with bill acceptors and 40

pounds for Vibes with coin). The processor and the terminal must be located no farther than

7 feet apart. Handle both components with care. Do not subject them to excessive vibration

or impact while mounting.

NOTE: The Vibe is not designed to function in an ambient
temperature in excess of 95ºF or 35ºC.

1 VIBE INSTALLATION AND OWNER’S MANUAL PM0352-10

Mounting the Terminal

NOTE: THIS INSTALLATION MUST ONLY BE PERFORMED BY A QUALIFIED SERVICE

TECHNICIAN.

The terminal has several different mounting options. Follow the instructions for the mounting

option you have chosen for your application. Make sure you are using sufficient hardware

to support the weight of the terminal for your application (22 pounds for Vibes with bill

acceptors and 50 pounds for Vibes with coin). The processor and the terminal must be

located no farther than 7 feet apart.

NOTE:

The lock on the terminal will only rotate approximately 45º-60º.

SETUP

CALIBRATE

BILL ACCEPTOR

BRACKET LOCK

BILL

ACCEPTOR

BRACKET

LOCK

LOCK RELEASE

PM0352-10 VIBE INSTALLATION AND OWNER’S MANUAL 2

FIGURE 1

- THE VIBE

(WITH BILL ACCEPTOR)

TERMINAL IN OPEN POSITION

FIGURE 1

- THE VIBE

(WITH COIN MECH)

TERMINAL IN OPEN POSITION

CALIBRATE

LOCK

LOCK RELEASE

SETUP

SCREWS
SECURING
COIN MECH

ASSEMBLY

(TO REMOVE COIN
MECH ASSEMBLY
REMOVE SCREWS

AND PUSH IN THE

COIN RETURN)

COIN RETURN

DETAIL VIEW

3 VIBE INSTALLATION AND OWNER’S MANUAL PM0352-10

FIGURE 2 - VIBE

WITH COIN MECH

TERMINAL - DETAIL VIEW OF COIN MECH BRACKET

THUMBSCREWS

DETAIL VIEW

COIN MECH

(AS SEEN THROUGH

BRACKET)

BRACKET LOCATION

FOR ALL OTHER

MOUNTING OPTIONS

ORIGINAL

BRACKET LOCATION

FOR TABLE OR

BAR TOP MOUNTING

Coin Mech Bracket Adjustment - VIBE with Coin Only

Vibe with Coin Only:

Depending on which mounting option you have chosen for

the terminal, a quick adjustment to the coin mech and bracket may be required.
If you are mounting the terminal using the table or bar top mounting option, the
mech and bracket are already in the correct position. If you are mounting the
terminal using any of the other mounting options, the mech and bracket must
be moved for proper operation of the mech. Follow the instructions below to
adjust the coin mech and bracket, if necessary.

Vibes with Coin Mechs Only:

(For Vibes with bill acceptors, continue with the mounting

option you have chosen.)

Unlock the terminal and push down on the lock release while carefully opening the front

of the terminal. See Figure 1.

Loosen the 2 thumbscrews on either side of the coin mech bracket. See Figure 2.

Pull the coin mech towards the front of the terminal as far as it will go and tighten the

thumbscrews to secure the mech in this position. See Figure 2.

The small bracket (secured by 2 screws) on the coin mech bracket must also be

adjusted. Unscrew the 2 screws securing the bracket (see Figure 2) and move the

bracket to the left as shown in Figure 2. Replace the 2 screws to secure the bracket.

Continue with the mounting instructions for the mounting option you have chosen.

NOTE: If you decide to change the mounting of the terminal to table or bar top

mounting, you must move the small bracket back to its original position and

return the coin mech bracket to its original position.

PM0352-10 VIBE INSTALLATION AND OWNER’S MANUAL 4

Surface Wall Mounting

To mount the terminal on the wall follow the instructions below.

NOTE: If you are mounting the terminal on the wall, the wall must not

be a structural, or load-bearing wall.

NOTE:

Vibe with Coin Only:

Mounting the terminal using this mounting option

requires a quick adjustment to the coin mech and bracket for proper operation

of the mech. Before mounting the terminal, follow the instructions on page 4

(Coin Mech Bracket Adjustment) to adjust the coin mech and bracket.

Using the supplied template (PM0353-02 for Vibes with bill acceptors and PM0409-01

for Vibes with coin mechs), drill the 4 holes needed to mount the terminal on the

mounting surface.

Unlock the terminal and push down on the lock release while carefully opening the front

of the terminal. See Figure 1.

Vibes with coin only:

Remove the coin mech assembly from the game by removing the

three screws securing the coin mech assembly and pushing in the coin return. See

Figure 1B.

Secure the terminal to the wall with sufficient hardware to support the weight of the

terminal (22 pounds for Vibes with bill and 50 pounds for Vibes with coin). See Figure

3A for Vibes with bill and 3B for Vibes with coin.

Vibes with coin only:

Replace the coin mech assembly and secure it with the three

screws.

Close and lock the terminal and continue with “Mounting the Processor”.

5 VIBE INSTALLATION AND OWNER’S MANUAL PM0352-10

FIGURE 3

- VIBE

WITH BILL ACCEPTOR

- SURFACE WALL MOUNTING OF TERMINAL

MOUNTING

SURFACE

ANCHORED

FASTENER
(4 REQUIRED)

FIGURE 3

- VIBE

WITH COIN MECH

- SURFACE WALL MOUNTING OF TERMINAL

MOUNTING SURFACE

ANCHORED

FASTENER
(4 REQUIRED)

PM0352-10 VIBE INSTALLATION AND OWNER’S MANUAL 6

7 VIBE INSTALLATION AND OWNER’S MANUAL PM0352-10

Recessed Wall Mounting

To mount the terminal in the wall follow the instructions below.

WARNING: Before cutting the hole for the terminal, make sure that there

are no electrical wires, pipes or supporting structures behind the wall

in the location where you are mounting the terminal. There must be 5

inches of space behind the wall in order for the terminal to be mounted in this

fashion. Follow all appropriate precautions while performing this installation.

NOTE: If you are mounting the terminal to the wall, the wall must not be a

structural, or load-bearing wall.

NOTE:

Vibe with Coin Only:

Mounting the terminal using this mounting option

requires a quick adjustment to the coin mech and bracket for proper operation

of the mech. Before mounting the terminal, follow the instructions on page 4

(Coin Mech Bracket Adjustment) to adjust the coin mech and bracket.

Using the supplied template (PM0353-01 for Vibes with bill acceptors and PM0353-03

for Vibes with coin), make the cutout for the terminal and drill the holes needed to mount

the terminal in the mounting surface.

Unlock the terminal and push down on the lock release while carefully opening the front

of the terminal. See Figure 1.

Vibes with coin only:

Remove the coin mech assembly from the game by removing the

three screws securing the coin mech assembly and pushing in the coin return. See

Figure 1B.

Route the wires from the back of the terminal through the cutout in the wall and secure

the terminal to the wall with sufficient hardware to support the weight of the terminal

(22 pounds for Vibes with bill acceptors and 50 pounds for Vibes with coin). See

Figures 4A for Vibes with bill and 4B for Vibes with coin.

Vibes with coin only:

Replace the coin mech assembly and secure it with the three

screws.

Close and lock the terminal and continue with “Mounting the Processor”.

PM0352-10 VIBE INSTALLATION AND OWNER’S MANUAL 8

FIGURE 4

- VIBE

WITH BILL ACCEPTOR

- FLUSH WALL MOUNTING OF TERMINAL

ANCHORED

FASTENER

(5 REQUIRED)

MOUNTING

SURFACE

CUTOUT

IN WALL

ANCHORED

FASTENER

(4 REQUIRED)

MOUNTING
SURFACE

CUTOUT
IN WALL

FIGURE 4

VIBE WITH COIN MECH

- FLUSH WALL MOUNTING OF TERMINAL

9 VIBE INSTALLATION AND OWNER’S MANUAL PM0352-10

Wall Mounting with Swivel Bracket

To mount the terminal on a wall using the swivel bracket follow the instructions below.

NOTE:

Vibe with Coin Only:

Mounting the terminal using this mounting option

requires a quick adjustment to the coin mech and bracket for proper operation

of the mech. Before mounting the terminal, follow the instructions on page 4

(Coin Mech Bracket Adjustment) to adjust the coin mech and bracket.

Use the wall bracket as a guide to locate and drill the six holes needed to secure the

bracket on the wall. Once you have drilled the six holes, install the wall bracket using

sufficient hardware to support the weight of the terminal and bracket (27 pounds for

Vibes with bill acceptors and 55 pounds for Vibes with coin mechs).

Attach the terminal bracket to the wall bracket by installing the machine screw

(1/4 - 20 x 1/2 L)

and 2 washers (.75 T x 1/2 ID x 7/8 OD and .83 T x 7/16 ID x 7/8 OD)

up through the hole in the wall bracket and then through the tab in the terminal bracket

as shown in Figure 5. The washer with the larger inside diameter must be closest to

the bracket. Make sure that the washers are centered and then loosely tighten the

machine screw. Install the hexnut to secure the bracket, and then fully tighten the

machine screw and hexnut.

Unlock the terminal and push down on the lock release while carefully opening the front

of the terminal.

Vibes with coin only:

Remove the coin mech assembly from the game by removing the

three screws securing the coin mech assembly and pushing in the coin return (see

Figure 1B).

Attach the terminal to the terminal bracket using the 4 supplied machine screws

(8 - 32 x 1/2 L) as shown in Figure 5.

Secure the bottom of the terminal to the bracket by installing the truss head screw

(3/8 - 16 x 3/4 L) and flat washer (.083 T x 7/16 ID x 7/8 OD) through the terminal and

into the pivot on the wall bracket as shown in Figure 5.

Vibes with coin only:

Replace the coin mech assembly and secure it with the three

screws.

Close and lock the terminal and continue with “Mounting the Processor”.

PM0352-10 VIBE INSTALLATION AND OWNER’S MANUAL 10

TRUSS HEAD

SCREW

FLAT

WASHER

TERMINAL

BRACKET

WASHERS

MACHINE
SCREW

MACHINE

SCREW

(4 PLACES)

WALL
BRACKET

PIVOT

HEXNUT

ANCHORED

FASTENER
(6 REQUIRED)

FIGURE 5 - SWIVEL BRACKET MOUNTING OF TERMINAL

11 VIBE INSTALLATION AND OWNER’S MANUAL PM0352-10

Column Mounting

To mount the terminal on a Lally column follow the instructions below.

NOTE:

In order to mount the terminal on the column brackets, the column must have a 4”

diameter.

NOTE:

Vibe with Coin Only:

Mounting the terminal using this mounting option

requires a quick adjustment to the coin mech and bracket for proper operation

of the mech. Before mounting the terminal, follow the instructions on page 4

(Coin Mech Bracket Adjustment) to adjust the coin mech and bracket.

Open one of the column brackets and clamp it to the column at the level where the

terminal will be mounted. Secure the bracket with the supplied machine screw

(3/8 - 16 x 1 - 1/2 L) as shown in Figure 6.

Open the second column bracket and clamp it to the column 4 inches from the first

bracket (measuring from the inside of one bracket to the inside of the second bracket).

Secure the bracket with the supplied machine screw (3/8 - 16 x 1 - 1/2 L) as shown in

Figure 6.

Attach the metal adapter plate to the column brackets using the 4 supplied machine

screws (3/8 - 16 x 1 L) as shown in Figure 6.

Install the 2 set screws (1/4 - 20 x 1/2 L) on either side of each column bracket to

secure the brackets. See Figure 6.

Unlock the terminal and push down on the lock release while carefully opening the front

of the terminal. See Figure 1.

Vibes with coin only:

Remove the coin mech assembly from the game by removing the

three screws securing the coin mech assembly and pushing in the coin return (see

Figure 1B).

Attach the terminal to the metal adapter plate using the 4 supplied machine screws

(10 - 32 x 3/4 L) as shown in Figure 6.

Vibes with coin only:

Replace the coin mech assembly and secure it with the three

screws.

Close and lock the terminal and continue with “Mounting the Processor”.

NOTE:

There is an additional hole provided on the column bracket to secure the bracket to

the column with a padlock if desired. The padlock must have an extra long shackle in order
to fit through the hole in the bracket.

13 VIBE INSTALLATION AND OWNER’S MANUAL PM0352-10

Column Mounting with Swivel Bracket

To mount the terminal on a column with the swivel bracket follow the instructions below.

NOTE:

In order to mount the terminal on a column, the column must have a 4” diameter.

NOTE:

Vibe with Coin Only:

Mounting the terminal using this mounting option

requires a quick adjustment to the coin mech and bracket for proper operation
of the mech. Before mounting the terminal, follow the instructions on page 4
(Coin Mech Bracket Adjustment) to adjust the coin mech and bracket.

Open one of the column brackets and clamp it to the column at the level where the

terminal will be mounted. Secure the bracket with the supplied machine screw

(3/8 - 16 x 1 - 1/2 L) as shown in Figure 7.

Open the second column bracket and clamp it to the column 9 inches from the first

bracket (measuring from the inside of one bracket to the inside of the other bracket).

Secure the bracket with the supplied machine screw (3/8 - 16 x 1 - 1/2 L) as shown in

Figure 7.

Attach the wall bracket to the column brackets using the 4 supplied machine screws

(3/8 - 16 x 1 L) as shown in Figure 7.

Install the 2 set screws (1/4 - 20 x 1/2 L) on either side of each column bracket to

secure the brackets. See Figure 7.

Attach the terminal bracket to the wall bracket by installing the machine screw

(1/4 - 20 x 1/2 L)

and 2 washers (.75 T x 1/2 ID x 7/8 OD and .83 T x 7/16 ID x 7/8 OD)

up through the hole in the wall bracket and then through the tab in the terminal bracket

as shown in Figure 7. The washer with the larger inside diameter must be closest to

the bracket. Make sure that the washers are centered and then loosely tighten the

machine screw. Install the hexnut to secure the bracket, and then fully tighten the

machine screw and hexnut.

Unlock the terminal and push down on the lock release while carefully opening the front

of the terminal. See Figure 1.

Vibes with coin only:

Remove the coin mech assembly from the game by removing the

three screws securing the coin mech assembly and pushing in the coin return (see

Figure 1B).

Attach the terminal to the terminal bracket using the 4 supplied machine screws

(8 - 32 x 1/2 L) as shown in Figure 7.

Secure the bottom of the terminal to the bracket by installing the truss head screw

(3/8 - 16 x 3/4 L) and flat washer (.083 T x 7/16 ID x 7/8 OD) through the terminal and

into the pivot on the wall bracket as shown in Figure 7.

10.

Vibes with coin only:

Replace the coin mech assembly and secure it with the 3 screws.

11. Close and lock the terminal and continue with “Mounting the Processor”.

NOTE:

There is an additional hole provided on the column bracket to secure the bracket to

the column with a padlock if desired. The padlock must have an extra long shackle in order
to fit through the hole in the bracket.

PM0352-10 VIBE INSTALLATION AND OWNER’S MANUAL 14

FIGURE 7 - LALLY COLUMN WITH SWIVEL BRACKET MOUNT

MACHINE SCREW

WASHERS

FLAT

WASHER

TRUSS

HEAD

SCREW

MACHINE

SCREW

(4 PLACES)

MACHINE

SCREW

(4 PLACES)

MACHINE
SCREW

SET SCREW
(2 PLACES)

OPTIONAL
PADLOCK

9"
REF

PIVOT

WALL BRACKET

HEXNUT

15 VIBE INSTALLATION AND OWNER’S MANUAL PM0352-10

Table or Bar Top Mounting with Base

To mount the terminal on a table or bar follow the instructions below.

NOTE: There are several options for table or bar top mounting. Make sure you
are following the instructions for the mounting option you have chosen.

NOTE: The coin mech and coin mech bracket are sent from the factory in the
proper position for this mounting option. No adjustments need to be made to

the coin mech if you are mounting the terminal using this option.

Table or Bar Top Mounting with the Base Support:

Peel the protective coating from the base support. Then peel the backing from the 5

base support pads and adhere the pads evenly to the bottom of the base support. (If

you received one large base support pad in place of the 5 smaller base support pads,

peel the backing from the pad and adhere the pad to the bottom of the base.) Also, peel

the backing from the base pad and adhere the pad to the bottom of the base.

Using the 2 supplied flat head Phillips screws (1/4 - 20 x 3/4 L), secure the base to the

base support as shown in Figure 8.

Unlock the terminal and push down on the lock release while carefully opening the front

of the terminal. See Figure 1.

Secure the terminal to the base with the supplied “dogbone” washer (with the hole in

the “dogbone” washer closest to the front of the terminal) and truss head screw

(3/8 - 16 x 1 1/4 L) as shown in Figure 8. Tighten the screw until the “dogbone” washer

conforms to the shape of the terminal.

Attach the 2 nuts to the U-bolt and then secure the U-bolt and the lanyard to the wire

cover bracket using the 2 kepnuts as shown in Figure 8.

Install the wire cover bracket routing the wires from the terminal underneath the

bracket and secure the bracket to the base with the 2 hex head bolts

(1/4 - 20 x 1/2 L).

Secure the free end of the lanyard (attached to the back of the base) with a screw

under the mounting surface. This provides necessary strain relief for the cables.

Close and lock the terminal and continue with “Dressing the Wires”.

PM0352-10 VIBE INSTALLATION AND OWNER’S MANUAL 16

FIGURE 8 - TABLE OR BAR TOP MOUNTING OF TERMINAL USING BASE SUPPORT

FLAT HEAD

PHILLIPS SCREW

SECURING

BASE SUPPORT

TO BASE

(2 PLACES)

TRUSS HEAD

SCREW

"DOGBONE"

WASHER

WIRE COVER

BRACKET

U-BOLT
(WITH NUTS

ATTACHED)

LANYARD
(ATTACH FREE END
UNDER MOUNTING
SURFACE)

BASE SUPPORT

BASE

NUT SECURING
U-BOLT
(2 PLACES)

HEX HEAD BOLT

SECURING WIRE
COVER BRACKET
(2 PLACES)

Dressing the Wires:

There are two options for dressing the wires between the terminal and processor. The

spiral wrap is included with the kit. It holds all of the wires together but it is not secured to

the mounting surface. The conduit can be purchased separately. It is self-adhesive and can

be adhered to the mounting surface. Conduit is recommended for units that are mounted on

the wall. Follow the instructions for the option you have chosen.

•

Spiral Wrap

Wrap the spiral wrap around the wires between the terminal and processor.

•

Conduit

Measure and cut the conduit to fit. Open the conduit and place the wires from the

terminal into the conduit. Peel the backing from the adhesive on the back of the conduit

and press the conduit on your mounting surface to secure it.

NOTE:

The conduit has a strong adhesive. It may be hard to remove from the surface.

If you want to remove the conduit use an adhesive remover.

After you have dressed the wires, continue with “Mounting the Processor”.

17 VIBE INSTALLATION AND OWNER’S MANUAL PM0352-10

Table or Bar Top Mounting - Two Hole Mounting Instructions:

Peel the backing from the base pad and adhere the pad to the bottom of the base.

Using the supplied template (PM0362-01) drill the 2 holes marked “A” on the template.

After drilling the holes, secure the base to the bar with 1/4” x 20 screws long enough

for your mounting surface. See Figure 9.

Unlock the terminal and push down on the lock release while carefully opening the front

of the terminal. See Figure 1.

Secure the terminal to the base with the supplied “dogbone” washer (with the hole in

the “dogbone” washer closest to the front of the terminal) and truss head screw

(3/8 - 16 x 1 1/4 L) as shown in Figure 9. Tighten the screw until the “dogbone” washer

conforms to the shape of the terminal.

Attach the 2 nuts to the U-bolt and then secure the U-bolt and the lanyard to the wire

cover bracket using the 2 kepnuts as shown in Figure 9.

Install the wire cover bracket routing the wires from the terminal underneath the

bracket and secure the bracket to the base with the 2 hex head bolts

(1/4 - 20 x 1/2 L).

Secure the free end of the lanyard (attached to the back of the base) with a screw

under the mounting surface. This provides necessary strain relief for the cables.

Close and lock the terminal and continue with “Dressing the Wires”.

Dressing the Wires:

There are two options for dressing the wires between the terminal and processor. The

spiral wrap is included with the kit. It holds all of the wires together but it is not secured to

the mounting surface. The conduit can be purchased separately. It is self-adhesive and can

be adhered to the mounting surface. Conduit is recommended for units that are mounted on

the wall. Follow the instructions for the option you have chosen.

•

Spiral Wrap

Wrap the spiral wrap around the wires between the terminal and processor.

•

Conduit

Measure and cut the conduit to fit. Open the conduit and place the wires from the

terminal into the conduit. Peel the backing from the adhesive on the back of the conduit

and press the conduit on your mounting surface to secure it.

NOTE:

The conduit has a strong adhesive. It may be hard to remove from the surface.

If you want to remove the conduit use an adhesive remover.

After you have dressed the wires, continue with “Mounting the Processor”.