manuals/manuals_Support_Center_Megatouch_Manuals_m7

MEGATOUCH™ 7 ENCORE EDITION KIT PM0273-02

Megatouch™ 7 Encore Edition

CONTENTS:

NOTE: IN ORDER TO INSTALL THIS KIT,

YOU MUST BE AT THE SUPER IV LEVEL

(PG9255-41) OR HIGHER. IN ORDER TO

DETERMINE WHAT LEVEL OF SOFT-

WARE YOUR GAME IS CURRENTLY RUN-

NING, LOOK AT THE EPROM AT U38.

REFER TO FIGURE 1 FOR LOCATION.

Turn off the game and disconnect it

from its power source.

NOTE: BEFORE HANDLING THE CRT-260
BOARD OR THE EPROMS, GROUND YOUR-
SELF TO REMOVE ANY STATIC CHARGE
THAT MAY BE ON YOUR BODY.

Locate and gain access to the CRT-

260 PC board (if unsure where to lo-

cate your CRT-260 board, see your

game manual).

Remove the existing program chips from

U32, U36, U37 and U38 from the CRT-

260 board. Also, remove the security

key from U5. (To remove the existing

key, you may need to cut away sili-

cone sealant holding the key in place.)

Be extremely careful not to dam-

age the board.

See Figure 1 for loca-

tions.

Installing the EPROMS

QTY

PART NUMBER

DESCRIPTION

SA3012

MEGA 7 U37 (4 MEG)

SA3014

MEGA 7 U32 (8 MEG)

SA3014

MEGA 7 U38 (8 MEG)

SA3045-02

USA, MEGA 7 KEY

GL3100-07

ENCORE EDITION DECAL, R, CTOP

GL3100-08

ENCORE EDITION DECAL, L, CTOP

PM8928-27

ENCORE EDITION SIGN

GL2401-12

ENCORE EDITION MARQUEE

HW8023-01

13/16" W T-MOULDING

Install the new EPROMS at U32, U37

and U38 and the new security key at

U5.

NOTE: WHEN INSTALLING EPROMS, BE
CAREFUL TO OBSERVE THE ORIENTATION
OF THE NOTCHES.

AVOID WALKING AROUND WITH THE
CHIPS IN YOUR HAND AFTER YOU HAVE
REMOVED THEM FROM THE BOX. THIS
COULD CAUSE STATIC TO BUILD UP.

Put the CRT-260 board back into place

and close all doors.

Plug the game in and turn on the power.

Perform a "2-Button Clear," by turning

on the game while simultaneously

pressing both the SETUP and CALI-

BRATE buttons (located behind the

cashbox).

Confirm that the checksum is as fol-

lows:

U32 = C193
U37 = 0E87
U38 = 8B6F

If one of the checksum numbers is in-

correct, check to make sure that the

EPROM is seated properly.

MEGATOUCH™ 7 ENCORE EDITION KIT PM0273-02

Turn off the game and disconnect it

from its power source.

Unlock and remove the coin mech from

the game.

Unlock and open the rear door.

Disconnect the ground braid and the

clear drainage tubing from the hood as-

sembly. See Figure 2.

Remove the thumbscrews and wash-

ers securing the lid, push the lid for-

ward, and remove it from the game.

See Figure 2.

Locate the seam on the T-moulding as

shown in Figure 2.

Using a screwdriver, carefully pry the

T-moulding away from the wood side

panel working around until entire T-

moulding is removed. Repeat the same

step for the other side of the game.

Install the provided T-moulding. Use a

rubber mallet to gently insert the T sec-

tion of the moulding into the wood side

panel. (Make sure that the T-moulding

seam is towards the bottom edge of

the side panel.) You will need to make

relief cuts where the T-moulding bends

around the game (see Figure 3). Re-

peat the same step for the other side

of the game.

NOTE: BE EXTREMELY CAREFUL WHEN
INSTALLING THE T-MOULDING. THE
GAME MUST BE TURNED OFF AND THE
LID MUST BE REMOVED FROM THE GAME
BEFORE USING THE RUBBER MALLET TO
INSERT THE T-MOULDING INTO THE SIDE
PANEL.

Replace the lid and reconnect the

ground strap and clear drainage tub-

ing.

10. Secure the lid to the game using the 2

thumbscrews and washers.

11. Put the coin mech back into the game

and lock it.

12. Close and lock the rear door.

13. Once the new T-moulding is in place,

remove the existing side decals. (Re-

move any remaining adhesive residue

with an adhesive remover.)

NOTE: Make sure not to get any adhe-
sive removing solvents or solutions
on the touchscreen, as they may dam-
age the touchscreen.

14. When you are finished removing any

excess adhesive from the game, wipe

the surfaces with alcohol solvent. The

surfaces must be clean and free from

dirt for the new decals to adhere prop-

erly.

15. Partially peel the backing from the top

edge of the provided decal. Center the

decal on the side of the game and ap-

ply the decal. There is a half inch ex-

cess around the entire decal to allow

for slight error. Cut away the excess

decal using the gap between the T-

moulding and the wood sides as a

guide. Repeat the same step for the

other side of the game.

16. Plug in the game and turn on the power.

Installing the T-Molding and
Side Decals

FIGURE 2 - HOOD ASSEMBLY

T-MOULDING PULLED AWAY FROM GAME

FIGURE 3 - SIDE VIEW OF T-MOULDING IN ROUTER HOLE

T-MOULDING WITH RELIEF CUT

PM0273-02 MEGATOUCH™ 7 ENCORE EDITION KIT 4

THUMBSCREWS
SECURING HOOD
TO MAIN CHASSIS

CLEAR DRAINAGE

TUBING

GROUND BRAID
ATTACHED TO REAR

DOOR

SEAM OF T-MOULDING

ROUTER HOLE

AROUND WOOD

SIDE PANEL

RELIEF CUT
NEEDED FOR

CORNERS

SIDE VIEW OF
T-MOLDING

T-MOLDING
(HW8023-01)

NOTES:

__________________________________________________________

___________________________________________________

_____________________________________________________

__________________________________________________

_____________________________________________________

_______________________________________________________

______________________________________________________

____________________________________________________

______________________________________________________

_________________________________________________________

________________________________________________________

______________________________________________________

_________________________________________________________