background image

COPYRIGHT © 2009 AMI ENTERTAINMENT NETWORK, INC.

HARD DRIVE 

DATA CABLE

HARD DRIVE 

POW ER CABLE

Troubleshooting Information - Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer

Megatouch Ion Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer

Hard Drive Removal

IMPORTANT NOTE:  If you are replacing a PATA hard drive with a SATA hard drive,

please see “PATA to SATA Hard Drive Conversion”.

Hard Drive Identification:

To determine whether your hard drive is quick-click or non-quick-click, look for a light gray adapter
between the hard drive adapter and the hard drive mounting bracket. See Figure 1. If there is such an
adapter, then you have a quick-click hard drive; if not, then your hard drive is non-quick-click. The PATA
hard drive with a clamp will simply have a clamp as shown in Figure 1. The SATA hard drive is also
shown in Figure 1. The SATA is easily identifable by the lack of a hard drive ribbon cable and adapter.

HARD 
DRIVE  

HARD DRIVE

ADAPTER

QUICK-CLICK

ADAPTER

HARD DRIVE

 

HARD

DRIVE

ADAPTER

FIGURE 1 - HARD DRIVES

Quick-Click Hard Drive Removal

1. If you are connected to TournaMAXX or TournaCHAMP you must perform an 

Update From Server

before removing the hard drive so that no information is deleted.

2. Turn off and unplug the game.

3. Unlock and open the CPU section.

4. Disconnect the hard drive adapter with the attached ribbon cable from the hard drive (Figure 2).

(a) Quick-click

(b) Non-quick-click

HARD DRIVE 

ADAPTER

HARD DRIVE

ADAPTER CLAMP

(d) SATA

(c) PATA hard drive with clamp

manuals/manuals_Support_Center_Ion_20Elite_20Edge_IonHardDrive_pdf-html.html
background image

COPYRIGHT © 2009 AMI ENTERTAINMENT NETWORK, INC.

Troubleshooting Information - Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer

Megatouch Ion Technical Reference Manual

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer (cont’d)

Quick-Click Hard Drive Installation

1. Attach the hard drive ribbon cable in the game to the new hard drive by lining up the left side of the

hard drive adapter with the pins on the hard drive, and then carefully inserting it all the way into the
quick-click adapter (see Figure 2 for proper orientation).

2. Slide the new hard drive assembly onto the game’s mounting plate. Align the mounting bracket

with the screw hole on the mounting plate, then secure the supplied screw in place (see Figure 2).

3. Close and lock the CPU section.

4. Plug in and turn on the game. The game will reboot twice to configure the hardware. When

prompted, perform a touchscreen calibration.

5. If you are connected to TournaMAXX or TournaCHAMP you must re-enter the dial-in settings after

completing the software upgrade. After entering the settings, make the initial call into the server and
then perform two 

Updates From Server

. Refer to the MegaNet manual for information on how to

perform these functions.

FIGURE 2 - QUICK-CLICK HARD DRIVE ASSEMBLY CONNECTION

SCREW SECURING 
HARD DRIVE 
ASSEMBLY TO 
MOUNTING PLATE 

HARD DRIVE ADAPTER 

(WRITING FACING OUT) 

HARD DRIVE RIBBON CABLE

WITH THE RED STRIPE ON THE CABLE

FACING RIGHT AND 2-PIN POWER 

CONNECTOR ON THE LEFT

QUICK-CLICK ADAPTER

ATTACHED TO

HARD DRIVE AND 

MOUNTING PLATE 

5. Remove the single screw securing the hard drive mounting bracket to the underlying mounting plate

(see Figure 2). This screw will not be reused.

6. Remove the hard drive and the attached bracket from the mounting plate by sliding the assembly

down and off its mounting plate.

manuals/manuals_Support_Center_Ion_20Elite_20Edge_IonHardDrive_pdf-html.html
background image

COPYRIGHT © 2009 AMI ENTERTAINMENT NETWORK, INC.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer

Megatouch Ion Technical Reference Manual

Non-Quick-Click Hard Drive Removal

1. If you are connected to TournaMAXX or TournaCHAMP you must perform an 

Update From Server

before removing the hard drive so that no information is deleted.

2. Turn off and unplug the game.

3. Unlock and open the CPU section.

4. Remove the single screw securing the hard drive mounting bracket to the underlying mounting

plate. See Figure 3.

5. Remove the hard drive assembly by sliding it down and off its mounting plate. Disconnect the hard

drive adapter, along with the hard drive ribbon cable, from the hard drive.

FIGURE 3 - NON-QUICK-CLICK HARD DRIVE REMOVAL

                

HARD DRIVE 
RIBBON CABLE 

SCREW SECURING 
HARD DRIVE 
MOUNTING BRACKET 

HARD DRIVE 

ADAPTER

manuals/manuals_Support_Center_Ion_20Elite_20Edge_IonHardDrive_pdf-html.html
background image

COPYRIGHT © 2009 AMI ENTERTAINMENT NETWORK, INC.

Non-Quick-Click Hard Drive Installation

1. Connect the hard drive adapter and attached ribbon cable to the supplied hard drive according to

Figure 4. Note that 4 pins on the hard drive are set off and will remain unconnected. Make certain
that the red stripe on the ribbon cable (indicating pin-1 position) is inserted facing the unconnected
pins. The writing on the plastic of the hard drive adapter and the black wire on the 2-pin power cable
should be facing out when installed into the game.

2. Slide the new hard drive assembly onto the hard drive mounting plate and secure it in place with a

single screw (Figure 3).

 
 
 
 

                                  

4 UNCONNECTED PINS 
(2 ROWS OF 2)

 

RED STRIPE 

ON HARD 

DRIVE 

RIBBON 

CABLE

FIGURE 4 - CIRCUIT-BOARD SIDE OF HARD DRIVE

3. Close and lock the CPU section.

4. Plug in and turn on the game. The game will reboot twice to configure the hardware. When

prompted, perform a touchscreen calibration.

5. If you are connected to TournaMAXX or TournaCHAMP you must re-enter the dial-in settings after

completing the software upgrade. After entering the settings, make the initial call into the server and
then perform two Updates From Server. Refer to the MegaNet manual for information on how to
perform these functions.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer

Megatouch Ion Technical Reference Manual

manuals/manuals_Support_Center_Ion_20Elite_20Edge_IonHardDrive_pdf-html.html
background image

COPYRIGHT © 2009 AMI ENTERTAINMENT NETWORK, INC.

PATA Hard Drive (with clamp) Removal

1. If you are connected to TournaMAXX or TournaCHAMP you must perform an 

Update From Server

before removing the hard drive so that no information is deleted.

2. Turn off and unplug the game.

3. Unlock and open the CPU section.

3. Remove the screw securing the hard drive mounting bracket to its mounting plate (see Figure 5).

This screw will not be reused.

4. Remove the hard drive from its mounting plate by sliding the assembly down  and off the mounting

plate. Disconnect the hard drive adapter and attached ribbon cable from the hard drive (see Figure
5). Then, separate the hard drive adapter from the ribbon cable and 2-pin power cable. This hard
drive adapter will not be reused.

FIGURE 5 - CLOSEUP OF PATA HARD DRIVE WITH CLAMP

HARD DRIVE RIBBON CABLE

HARD DRIVE ADAPTER

SCREW SECURING HARD 
DRIVE MOUNTING 
BRACKET 

HARD DRIVE 
ADAPTER CLAMP 

 

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer

Megatouch Ion Technical Reference Manual

manuals/manuals_Support_Center_Ion_20Elite_20Edge_IonHardDrive_pdf-html.html
background image

COPYRIGHT © 2009 AMI ENTERTAINMENT NETWORK, INC.

PATA Hard Drive (with clamp) Installation

1. Attach the 2-pin power cable in the game to the new hard drive adapter, which comes attached to

the new hard drive. Do so by locating the two stand-alone pins on the hard drive adapter, and then
sliding the 2-pin adapter onto these pins (for help, see the label on the hard drive adapter - see
Figure 5). Note: The black wire on the power cord MUST be facing toward the label side of the hard
drive adapter. Failure to do so could result in a damaged hard drive.

2. Attach the hard drive ribbon cable in the game to the new hard drive. Do so by lining up the pins on

the hard drive adapter with the mating holes on the ribbon cable (the red stripe on the ribbon cable
should be on the side opposite the power cable). Carefully insert the ribbon cable all the way into
the adapter so that it is fully seated.

3. Slide the new hard drive assembly onto the game’s mounting plate. Be sure that the hard drive is

flush to the mounting plate when doing so. Both the label on the plastic of the hard drive adapter
and the label on the hard drive itself should be facing out. Align the hole in the mounting bracket
with the hole on the mounting plate, then secure the supplied screw, washer, and clamp to the
mounting plate (see Figure 5). The clamp should rest on the hard drive adapter, holding it in place
when screwed in tightly.

4. Close and lock the CPU section.

5. Plug in and turn on the game. The game will reboot twice to configure the hardware. When

prompted, perform a touchscreen calibration.

6. If you are connected to TournaMAXX or TournaCHAMP you must re-enter the dial-in settings after

completing the software upgrade. After entering the settings, make the initial call into the server and
then perform two Updates From Server. Refer to the MegaNet manual for information on how to
perform these functions.

ATTENTION:

OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer (cont’d)

Troubleshooting Information - Removal/Installation of Major Assemblies -

Ion eVo/eVo Wallette/Elite Edge/Megatouch Entertainer

Megatouch Ion Technical Reference Manual

manuals/manuals_Support_Center_Ion_20Elite_20Edge_IonHardDrive_pdf-html.html